Keurig Brewer B70 Owners Manual

							USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new 
Platinum B70  Keurig® Brewer
COMMENT UTILISER VOTRE CAFETIÈRE
MANUEL D’UTILISATION : Tirez le meilleur de votre   
nouvelle cafetière Platinum B70 de Keurig
® 
						

							3
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEMPlatinum B70 —  Using Your Brewer
SET-UP
Helpful Hints  ........................................................................................
4
Unpacking  ............................................................................................4
Features  ...............................................................................................5
SECTION 1  —  SET-UP & FIRST BREW
Set-Up & First Brew  ...........................................................................6
SECTION 2  —  CONTROLS & INDICATORS
Setting the Clock  ...............................................................................10
Programming On/Off Features  ......................................................10
Programming Brew Temperature  .................................................12
Programming Brew Size  .................................................................13
SECTION 3  —  CLEANING & MAINTENANCE
Cleaning  ..............................................................................................13
De-Scaling ..........................................................................................14
Storage ...............................................................................................15
SECTION 4  —  TROUBLESHOOTING ..................................................16
SECTION 5   —  WARRANTY ................................................................17
 
Pour des directives en français, veuillez vous reporter à la page 18.
Record your Brewer Serial Number here.
2
Removing the serial number label from the Brewer will void warranty. 
IMPORTANT SAFEGUARDS  Safe Operation & Use
When using electrical appliances, basic 
safety precautions should be followed, 
including the following:
1.    Read all instructions before using.
2.   
Do not touch hot surfaces. Use handles and
knobs when available.
3.   This appliance must be properly installed and 
located in accordance with these instructions 
before it is used.
4.   The use of accessory attachments not recom -
mended by the appliance manufacturer may re -
sult in fire, electrical shock or injury to persons.
5.   Do not place on or near a hot gas or electric 
burner, or in a heated oven.
6. Do not use outdoors.
7.  To protect against fire, electric shock and injury 
do not immerse cords, plugs, or the appliance in 
water or any other liquid.
8. Do not overfill the Water Reservoir with water.
9.   Use  only water  in this appliance! Do not put any 
other liquids or foods in the Water Reservoir 
except as instructed in the Cleaning Instruc -
tions in this guide.
10.   Turn off and unplug the Brewer before 
cleaning or maintenance. Allow to cool   before putting on or taking off parts and 
 
before cleaning the appliance.
11.   For best operation, plug the appliance into its 
own electrical outlet on a dedicated circuit to 
prevent flickering of lights, blowing of fuses or 
tripping a circuit breaker.
12.   Do not operate any appliance with a damaged 
cord or plug or after the appliance malfunc -
tions or is damaged in any manner. Contact 
Keurig
® Customer Service to report any 
malfunction of or damage to the Brewer.
13.   Do not let the cord hang over the edge of 
the table or counter, or touch hot surfaces.
14.   To disconnect, press the Power Button on the 
Brewer to ‘OFF’ status and then remove the 
plug from the wall outlet.
15.  Close supervision is necessary when any 
appliance is used by or near children.
16.  Do not lift the Handle to open the Lid of 
the Brewer while brewing is in progress.
17.  Always keep the Water Reservoir Lid on 
the Water Reservoir unless you are refilling it.
18.   This appliance is equipped with a power cord 
having a grounding wire with a grounding plug. 
The appliance must be grounded using   
a 3-hole properly grounded outlet. In the  event of an electrical short circuit, grounding 
reduces the risk of electrical shock.
19. 
 If the outlet is a standard 2-prong wall outlet, 
it is your personal responsibility and obligation 
to have it replaced with a properly grounded 
3-prong wall outlet.
20.   Do not, under any circumstances, cut or 
remove the third (ground) prong from the 
power cord or use an adapter.
21.   Consult a qualified electrician if the grounding 
instructions are not completely understood, or 
if doubt exists as to whether the appliance is 
properly grounded.
22.   Do not use the appliance for other than
its intended use.
Sav E Th ESE 
I NSTRUCTIONS .
WaRNING TO USERS  aND P aRENTS
1. DO NOT  permit children to use brewer unless there 
is adult supervision. Brewer dispenses very hot water.
2. SPECI aL NOTICE FOR  hOT COCO a USERS:    
IMMEDI aTELY  aFTER USING  a h OT COCO a K-CUP,   
RUN a  hot Water Brew Cycle  without a K-Cup to avoid 
the possibility of clogging the exit needle.  DO NOT assume 
the next user will do this. 
CAUTION: There are two sharp needles that puncture the K-Cup® portion pack, 
one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To 
avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup Holder during the 
brew  process. To avoid risk of injury, do not lift the Handle or open the K-Cup  As-
sembly Housing during the brewing process.
SHORT CORD INSTRUCTIONS:
 A short power supply cord is provided to 
reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set 
or extension cord should be at least as great as the electrical rating of the 
appliance; (2) the cord should be arranged so that it will not drape over the 
countertop or tabletop where it can be pulled on by children or tripped over un -
intentionally; and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR  hOUSE hOLD USE ONLY.
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING 
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, 
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
WARNING: TO REDUCE THE RISK OF FIRE OR 
ELECTRIC SHOCK, DO NOT REMOVE THE 
BOTTOM COVER. NO USER SERVICEABLE 
PARTS ARE INSIDE. REPAIR SHOULD BE DONE 
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR  
ELECTRIC SHOCK   DO NOT OPEN
!  
						

							Set-up
5
Features  Platinum — Model B70 Brewer
A. Water Reservoir Lid
B. Water R eservoir
C.  Water Reservoir 
Lock Tab Slot
D. Handle
E. Funnel
Platinum B70 Brewer Controls 
 
and Indicators
h elpful  hints 
1.    Keep your Brewer turned “ON” at all times.   
To brew a fresh cup of coffee, tea or hot cocoa 
anytime you want, we suggest you keep your 
Brewer turned “ON” all the time. However, the 
Brewer is fully programmable so you can set it 
to turn on and off automatically to match your  schedule. Or, if you prefer, set the Brewer to   
automatica lly turn off after a period of time.
Follow the simple instructions on pages 10–13 
to make using the Brewer convenient for you.
2.    For the best tasting gourmet coffee, tea or 
hot cocoa, Keurig recommends using bottled 
water or the Keurig
® Water Filter Starter Kit 
(available at www.keurig.com). 
Water quality varies from place to place. If you  notice an undesirable taste in your cup of   
coffee, such as chlorine or other min eral tastes, 
we recommend you consider using bottled 
water or water from a filtration system.
3.    Customize the Size, Flavor & Brew That’s   
Perfect for You.™ 
With the choice of over 200 varieties of K-Cups  and 5 brew sizes (Iced Beverage-3.25 oz., Small 
Cup-5.25 oz., Small Mug-7.25 oz., Large Mug-
9.25 oz., and Travel Mug-11.25 oz.) your Keurig
® 
Brewer gives you endless options to customize 
the size, flavor and brew that’s perfect for you.  For a strong, intense cup, select an Extra Bold 
K-Cup
® (with up to 30% more ground coffee 
than regular varieties) and brew the size that’s  right for you. The smaller the brew size, the 
more intense flavor in your cup. The larger the 
brew size, the less intense flavor in your cup. 
4.    Plug Brewer into its own grounded outlet. 
If the electric circuit is overloaded with other 
appliances, your Brewer may not function 
properly. The Brewer should be operated on its  own circuit, separate from other appliances.
5.   
Brewing into a travel mug. 
To brew into a travel mug, simply remove the 
Drip Tray Assembly and place the travel mug on the Drip Tray Base.
6.   
De-scale Brewer regularly.    
Please see pages 14 and 15 for instructions.
Unpacking Instructions
1.  
Place Brewer box on a large steady surface
(such as a table or countertop) or on the floor.  Open the box.
2. Remove enclosed literature.
3.  
Turn the box on its side with front of box face down.
4.   Reach into the box and grasp the plastic bag 
that contains the Brewer.
5.   Carefully pull the plastic bag (and packaging 
materials) toward you and out of the box. The 
Brewer will still be encased in the polyfoam   
and be on its side.
6.  
Remove the top polyfoam packaging material.
7.  
Carefully lift Brewer off of the bottom polyfoam 
and place it upright on a flat, steady surface.
8.   Lift plastic bag off of Brewer.
9.  
Record the serial number for this Brewer on 
page 3 of this guide. The serial number can be 
found on the bottom of the Brewer box or on the  Brewer behind the Drip Tray (when removed).
10.  
Place the Brewer upright on a flat, steady 
surface. Remove tape holding Water Reservoir  in place. 
We recommend you save all packing materials in  case future shipping of the product is necessary.
WARNING: 
Keep all plastic bags away  from children.
4
M E N U
B R E W
M E N U
R
E A DY
TO  B R E W
a
B
M
C
I
N
L
K
J
h
E
G
D
F
T
R
S
P
0
Q
P. LCD Control Center
Q. Left Button
R. Right Button
S. MENU Button
T. BREW Button
F.   K-Cup® Portion Pack 
Holder (E and F are the   
K-Cup Holder Assembly) 
G.  Lid
H.  
K-Cup® Portion Pack 
Assembly Housing
I.  Housing
J. Drip Tray Plate
K. Drip Tray
L. Drip Tray Base
M. Vent
N. Power Cord
O.  
Power Switch (Not 
shown) Located Rear 
Right Side of Brewer       
						

							SECTION 1  Set-Up & First Brew
5.  Place a K-Cup portion pack 
in the K-Cup Holder (fig. 6). 
CAUTION: There are two sharp needles that
puncture the K-Cup, one above the K-Cup Holder 
and the other in the bottom of the K-Cup Holder. 
To avoid risk of injury, do not put your fingers in  the K-Cup Assembly Housing.
6.    
Lower the Handle to close the Lid over the
K-Cup Holder. (When it is closed completely, the LCD Control Center will indicate “READY 
TO BREW”. The Left and Right Buttons will  be lit and the BREW Button will flash up to 60 
seconds.)
a.   
All brew size icons are lit with the default 
size flashing (fig. 7). To choose a different size,   
press Left Button to go down in size or Right  Button to go up in size. 
NOTE: The Small Mug (7.25 oz. serving) is the 
factory set default brew size. To program your 
favorite brew size se e page 13 “Programming 
Your Brew Size”.
b.
      
Your choices are a stronger Small Cup (5.25 
oz. serving), a Small Mug (7.25 oz. serving), a  Large Mug (9.25 oz. serving), a Travel Mug 
(11.25 oz. serving) or Iced Beverage setting 
(3.25 oz. serving).
the Water Reservoir during this and subsequent   
heating  —  this is normal. 
9.
    Press the BREW Button to start a cleansing 
brew without a K-Cup. Pour the hot water into the sink.   
NOTE: A K-Cup should not be used for this 
Sequence
.
10.    
The one-time set-up process is now 
complete and you are ready to brew! 
NOTE: The Brewer may take 15-30 seconds 
between brews and then “READY TO BREW”   
will be displayed.
Ready to Brew Your First Cup
 1.  
LCD Control Center will indicate 
“READY TO BREW”. 
2. Place a cup or mug on the Drip Tray Plate.
3.  
Lift the Handle and the K-Cup® Holder 
 
will open toward you (fig. 5).
4.   Select a K-Cup portion pack.
NOTE: Do not remove the foil lid 
or puncture the K-Cup.M E N U
B R E W
M E N U
R
E A DY
NOT
Setting Up Your Brewer
1.   
Unwrap cord and plug the Brewer into 
a grounded outlet. Remove all pieces of   
packing tape and clear plastic sticker   
from LCD display.
2.   
Place a large mug (10 oz. minimum) on the 
Drip Tray Plate.
3.   
Remove the Water Reservoir from Brewer 
by first removing Lid from the Water Reservoir 
(fig. 1), then lifting the Water Reservoir straight 
up and toward front of Brewer. (may be tight),  (fig. 2). Rinse with fresh water.
4.   
Fill Water Reservoir with bottled or filtered 
water so that the water level is just below the 
top edge of the Water Reservoir.
IMPORT aNT:  You cannot use your Keurig® Brewer until 
it has been set up for its first use.
NOTE: If Brewer has been exposed to temperatures
below freezing, allow Brewer at least two hours to 
reach room temperature before brewing. A frozen   
or extremely cold Brewer will not operate.
5.    Place Water Reservoir base into 
the left side of the Brewer and be 
sure the Water Reservoir Lock 
Tab engages with the Brewer.  Replace Lid on Water Reservoir.
6.   
Press and release the Power 
Switch found directly behind the 
right side of the Brewer. Switch   
is spring loaded and will return   
to original position.
7.   
The Blue LCD Control Center 
will come on and indicate “NOT 
READY” and the BREW Button  will flash. 
NOTE: A K-Cup should 
not be used for this sequence
.
8.    
The Brewer will automatically fill the internal 
tank with water and then the water will be 
heated. This will take about 4 minutes. 
During the heating period, “NOT READY”   
(fig. 3) is displayed on the LCD Control Center.  Do not lift Brewer  handle during this 
‘heating period’. Once the water is heated, 
“READY TO BREW” will be displayed and the  BREW Button will flash (fig. 4). 
NOTE: You may see small amounts of water 
coming from the Vent and dripping into 
M E N U
B R E W
M E N U
R
E A DY
TO  B R E W
fig. 3
fig. 4
fig. 6
fig. 1
fig. 5
M E N U
B R E W
M E N U
R
E A DY
TO  B R E W
fig. 7
67
fig. 2Lock Tab                                                                                                       
						

							89
c.   
To use the Iced Beverage setting, place a tall 
glass filled with ice on the Drip Tray Plate. Use  your favorite K-Cup
®, select the Iced Beverage 
brew size and press the BREW Button. Add 
more ice once brewing is complete, add cream 
and sugar if desired.
d.   
Once size is chosen, press BREW Button. 
BREW Button will stop flashing, Left and Right 
Buttons will no longer be lit and icon   
of brew size will be lit.
7.    The LCD Control Center will now display the 
word ‘BREWING’ and the serving size you   
selected will be illuminated on LCD (fig. 8). 
CAUTION: There is extremely hot water in the K-
Cup Holder during the brew process. To avoid risk 
of injury, do not lift the Handle or open the   
K-Cup Assembly Housing during the brew process.
8.
   
There may be a short pause prior to coffee 
being dispensed. The entire brew process lasts 
for approximately 1 minute and ends with a 
burst of air to remove all liquid from the K-Cup.
9.   
Lift the Handle, remove and dispose 
of the used K-Cup.   
CAUTION: K-Cup will be hot.
10.  
Enjoy your first cup of Keurig Brewed® 
gourmet coffee, tea or hot cocoa!
11.   
Your Brewer may display “NOT READY” as 
it heats water for the next brew cycle. The 
“READY TO BREW” indication will return to   
the LCD Control Center in about 15 seconds.
 
Stopping the Brew Process
If you need to stop the brewing after the process has started, press and 
release the Power Switch to turn the Brewer ‘OFF’. The flow of coffee, tea 
or hot cocoa will stop, the heating element will shut off and the blue lights  illuminating the LCD Control Center and Water Reservoir will disappear. 
NOTE: You may get more coffee, tea or hot cocoa in your cup during your next 
brew. We recommend that you perform a cleansing brew with water-only after   
a terminated brew. Then your NEXT brew will be the volume you have selected.
a dding Water
The LCD Control Center of your Brewer will indicate when the water level 
in the tank is low or if the Water Reservoir  has been removed by displaying 
the words “ADD WATER” (fig. 9). The blue light in the Water Reservoir will 
also blink when water needs to be added. The Brewer will not allow you to  brew when “ADD  WATER” is displayed (fig. 9). 
SECTION 1Set-Up & First Brew (continued)
The Water Reservoir can be filled in two ways. 
1. 
 
Lift off the Water Reservoir Lid and pour  water directly into the Water Reservoir   
while it is still attached to the Brewer,   
then replace the Lid.
2.   
Remove the Water Reservoir from Brewer by 
first removing Lid from the Water Reservoir, then lifting the Water Reservoir straight up and toward 
front of Brewer. Fill with water. Place the Water 
Reservoir back on the Brewer and replace the Lid.
IMPORTANT : Do not remove the Water Reservoir 
during the brewing process.
Brewing  hot Water
Your Brewer is able to produce hot water for making hot cocoa from a packet, 
for use in cooking, for making soups, etc. Simply follow the instructions on 
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup. 
 
NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water   
 brew cycle without a K-Cup.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge 
the water from the inner tank.
1.   
If there is water in the Water Reservoir, remove the Lid, then lift the 
Water Reservoir straight up and away from Brewer. Discard water, rinse 
and refill with water. Place the Water Reservoir back on the Brewer and  replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2.   
Be sure the Brewer is turned on. Raise and lower the Handle on the 
Brewer without inserting a K-Cup.
3.   
The LCD Control Center will display “READY TO BREW”. 
Brew a Travel Mug (11.25 oz. serving) of water (do not use a K-Cup). 
4.   
Repeat steps 2 and 3 two more times to completely purge water from 
inner tank.
If you are experiencing any problems with your Brewer, please contact   
Customer Service at 1.866.901.BREW (2739).
 
Small Cup(5.25 oz.)  
Small Mug(7.25 oz.)
Large Mug(9.25 oz.) 
Travel Mug(11.25 oz.)
Iced Beverage(3.25 oz.) 
M E N U
B R E W
M E N U
ADD
WATER
R E A DY
NOT
fig . 9
M E N U
B R E W
M E N U
B
R E WIN G
fig . 8      
						

							1011
SECTION 2  Controls & Indicators (LCD Control Center)b.  
Press or hold the Left Button under the 
blinking “H” to advance 1 hour at a time, up   
to 9 hours. 
c.   
After setting the desired Auto Off time, press 
the MENU Button five times to scroll through 
the remaining programming options and exit 
the  programming mode. “AUTO OFF SET” 
(fig. 12) will now be displayed to indicate that it  has been  set. 
d.    To cancel the Auto Off feature, press the 
MENU Button twice to reach the “AUTO OFF” 
programming mode. Press and release the  blue Left Button under the blinking “H”   
to advance one hour at a time until “OFF”   
is displayed.
3.   Program your Brewer for a specific On/Off
Time. 
NOTE : To use this programming feature, 
the clock must be set to the correct time. The 
clock will not be displayed unless the time is set.
a.   
After setting the correct time (required), press 
the MENU Button three t imes to program 
On Time feature . The LCD Control Center will 
show the programming options with a small  arrow next to “SET ON TIME” (fig. 13).  
b.   
Press or hold the Left Button under the “H” to 
scroll through the hours to your desired “ON 
TIME” hour.
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in  the LCD Control Center. 
NOTE: You must set the clock if you will be using the 
Auto On/Off Time programming feature.
1. 
Press the MENU Button.
2.  
The word ‘OFF’ will appear at the top of the 
LCD Control Center to indicate that the 
clock is not set (fig. 10). The programming  options will appear on the LCD Control  Center with a small arrow pointing to ‘SET 
CLOCK’. “H” (Hour) will appear above the 
Left Button and “M” (Minute) will appear 
above the Right Button. The “H” and “M”  icons and Left and Right Buttons will flash.
3.    Press or hold the Left Button under the 
flashing “H” until you have reached the 
appropriate hour. If the hour has passed 12 
“PM” will be shown.
4.   
Press or hold the Right Button under the 
flashing “M” to set the minutes.
5.   
When you have reached the correct time, press the MENU Button six 
times to scroll through the remaining programming steps.
Set
Hours Set
Minutes
M E N U
B R E W
M E N U
SET
 CLOCK
AUTO  OFF 
  ONOFF TIME 
BREW TEMP 
BREW SIZE
M
H
R E A DY
NOT
fig . 10
6.   The correct time should now be displayed in the LCD Control Center.
NOTE: If power is interrupted to the Brewer by unplugging it, or if power is 
lost, follow the procedure above to reset the time as the clock will not be 
visible until the time is set. Brew size and brew temperature menu settings 
are remembered and restored automatically. All other settings will be  restored automatically after clock is set.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea  or hot cocoa on your own schedule. By programming your Brewer to turn on 
each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to  warm up from room temperate.
1.    Leave it ON all the time. The Brewer can be left on all the time so that it is 
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To  turn the Brewer off at any time, simply press and release the Power Switch. 
( NOTE :
 Although the clock remains on, if set, you can not brew a cup of coffee, 
tea or hot cocoa.) 
Press and release the Power Switch again to restore 
power to the Brewer. You will have to wait for the water to heat up before  the Brewer is ready to brew.
2.   Set the Brewer to “AUTO OFF” following a specified period of time after the 
last brew.
  
a.   
Press the MENU Button twice to program the Auto Off feature. The LCD 
Control Center will now di splay the programming options with a small 
arrow next to “SET AUTO OFF” (fig. 11). c. 
 
Press or hold the Right Button under the 
“M” to scroll through the minutes to your  desired “ON TIME” minutes.
d.   
After setting the des ired time, press the 
MENU Button to save the “ON TIME” and 
move to the “SET OFF TIME” (fig. 14). 
e.   
If you want to set an “OFF TIME”, repeat the 
procedure above in steps b  & c to set your 
desired “OFF TIME” (fig. 14). 
f.   
To complete the process, press the MENU 
Button three more times to exit the 
programming mode. The Control Center  will now indicate the options you have set.
g.   
The Auto On time and Auto Off time functions 
operate independently from one another. To 
cancel either set function, follow the steps  above and use the “H” and “M” Buttons to 
advance to 12:00 AM. Make sure the “M” Button is set to :00, then change the “H” 
Button. When you reach 12:00 AM, the Control Center will display ‘OFF’ and the function will be disabled.
EX AMPLE : If you chose to set the On Time at 
6:55 AM and the Off Time for 10:00 PM, then  the Brewer will be “READY TO BREW” and 
maintain hot water in the tank during that  time so that it is always ready for you to brew. 
If you wanted to brew outside this window, 
fig . 11
M E N U
B R E W
M E N U
AUTO 
OFF SET
RE A DY
TO  B R E W
fig. 12
Set
Hours Set
Minutes
M E N U
B R E W
M E N U
CLOCK
  AUTO  OFF 
SET  ON TIME 
BREW TEMP 
BREW SIZE
M
H
R E A DY
NOT
fig . 13
Set
Hours Set
Minutes
M E N U
B R E W
M E N U
CLOCK
  AUTO  OFF 
SET OFF TIME 
BREW TEMP 
BREW SIZE
MPMH
R E A DY
NOT
fig . 14   
						

							13
simply press the Power Button and you can brew as soon as the water is heated and the 
“READY TO BREW” indicator is displayed on   
the LCD Control Center. 
NOTE :
 The On time and Off time functions 
operate independently from one another. To  cancel either function, follow the steps above  and use the “H” and “M” Buttons to advance to 
12:00 AM. When you reach 12:00 AM, the Control Center will display ‘OFF’ and the 
function will be disabled  (fig. 15).
NOTE:  The Auto Off timer and the On/Off Time 
programming options operate independently,  but can also be programmed to work together. 
For example, you can set the On Time function to  turn on at 7:00 AM and then set the Auto Off timer 
function to turn off the Brewer two hours after  the last brew.
SECTION 3  Cleaning & MaintenanceSECTION 2 Controls & Indicators (LCD Control Center)
12
fig. 15Programming Brew Temperature  (187°  –  192º F)
The Brewer brews at a preset temperature of 192°. You can adjust this 
temperature down by 5 degrees if you prefer a cooler cup of coffee, tea   
or hot cocoa. Simply follow the instructions below.
1.   
Press the MENU Button on the LCD Control 
Center five times to program the Brew 
Temperature feature.
2.   
The LCD Control Center will now display 
the programming options with  a small 
arrow next to “SE T BRE W  TEMP” (fig. 16). 
Also, the temperature 192° (initial setting)  will be displayed at the top of the LCD 
Control Center to indicate the current  temperature setting.
3    .  
A minus sign will appear over the Left 
Button and/or a plus sign over the Right 
Button. Use these Buttons to raise or lower the temperature one degree at a time.
4.    Once you have reached your desired brew 
temperature, press the MENU Button twice 
to exit the programming mode. “BREW TEMP 
SET” will be displayed in the LCD Control  Center if you have changed it from 192°.
M E N U
B R E W
M E N U
 
CLOCK
AUTO  OFF SET
  ONOFF TIME SET
SET BREW TEMP   BREW SIZE
+
-R E A DY
NOT
-+
fig . 16
5.   To change the brew temperature again, repeat steps 1 through 3 to change 
the temperature up or down, remembering that the temperature can only 
be between 187°  and 192° . 
NOTE: At high altitudes (over 5,000 feet) if boiling occurs use the tempera -
ture adjustment (+0 and -5 degrees) to lower the temperature.
Programming Your Brew Size
 
The Brewer is preset with the Small Mug   
(7.25 oz.) as the default brew size. The default  brew size allows the user to avoid scrolling through brew sizes if a particular size is   
chosen most often.
To change the default brew size to your   
desired brew size:
1.   
Press  the MENU Button six times.
2.   
Using Left and Right Buttons, select your 
desired default brew size (fig. 17). 
3.   
Once the desired default brew size is selected 
press the MENU Button once to exit. Th e LCD 
will display the brew size set.
M E N U
B R E W
M E N U
R
E A DY
TO  B R E W
fig. 17
Cleaning External Parts
Regular cleaning of the Brewer’s external components is recommended.
1.  
Never immerse the Brewer in water or other liquids. The Housing 
and other external components may be cleaned with a soapy, damp,   
non-abrasive cloth.
2.   
The Drip Tray can accumulate up to 12 ounces of overflow. The Drip Tray 
and Drip Tray Plate should be periodically inspected and rinsed clean.   
To remove the  Drip Tray Assembly, simply slide it toward you, keeping it 
level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should 
not be placed in the dishwasher.  They should be cleaned with a damp, 
soapy, non-abrasive cloth and rinsed thoroughly. 
Cleaning the K-Cup  holder 
a ssembly
1.   
Cleaning the Parts  —The K-Cup Holder 
Assembly can be placed onto the top shelf of a 
dishwasher. 
NOTE:  Use low temperature cycles 
in the dishwasher. 
To remove from the Brewer, 
open the cover by lifting the Handle. Grasp the  top of the K-Cup Holder with one hand while 
push ing up on the bottom of the K-Cup
® Holder 
from underneath with the other until it releases 
(fig. 18). After cleaning, align the K-Cup Holder  with the openi ng using the two front ribs as a 
guide, and snap into place from the top. 
fig . 18
Set
Hours Set
Minutes
M E N U
B R E W
M E N U
SET
 CLOCK
AUTO  OFF 
  ONOFF TIME 
BREW TEMP 
BREW SIZE
M
H
R E A DY
NOT               
						

							2.  
Cleaning the Funnel  —The Funnel can be 
removed from the K- Cup® Holder by pulling 
on it until it pops off (fig. 19). The Funnel is 
dishwasher safe. To replace it, just snap it   
back onto the K-Cup Holder Assembly.
3.    Cleaning the Exit Needle  —The Exit Needle is 
located on the inside bottom of the K-Cup 
Holder Assembly. Should a clog arise due to 
coffee grinds, it can be cleaned using a paper 
clip or similar tool. Remove K-Cup Holder  assembly and detach Funnel. Insert the paper 
clip (as shown in fig. 19) into the Needle to  loosen the clog and push it o ut. The K-Cup 
Holder is dishwasher safe. 
CAUTION : There are sharp needles that puncture the K-Cup above the K-Cup 
Holder  and in the bottom of the K-Cup Holder. To avoid risk of injur y, do not 
put your fingers in the K-Cup A ssembly Housing.
Cleaning the Water Reservoir & Water Reservoir Lid
The Water Reservoir Lid or Water Reservoir should not be put into the  dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth and rinsed thoroughly. Do not dry the inside of the Water Reservoir with a 
cloth as lint may remain.    
CAUTION: Please rinse the Water Reservoir thoroughly after cleaning to ensure 
that no cleaners or cleaning solutions remain in this area as they may contaminate 
the water supply in the Brewer.
SECTION 3 Cleaning & Maintenance (continued)
!
fig. 19De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the mineral 
content of the water in your area, calcium deposits or scale may build up in  your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer 
performance. De-scaling your Brewer helps maintain the heating element 
and other internal parts of the Brewer that come in contact with water. 
The Brewer should be de-scaled every 3-6 months to ensure optimal performance. It is 
possible for calcium deposits to build up faster, 
making it necessary to de-scale more often.
This Brewer is equipped with sensors to   
detect when scale buildup is interfering with  the performance of the Brewer. When this is 
detected, “DE-SCALE” will  be displayed on 
the LCD Control Center (fig. 20). How ever, 
even if “DE-SCALE” is not displayed, you  should continue to de-scale your Brewer   
every 3-6 months.
You should promptly de-scale if “DE-SCALE” is  displayed on the LCD Control Center. Properly  follow the de-scaling procedure described.
NOTE:  The Brewer will continue to function even when “DE-SCALE” is displayed. 
However, if you do not de-scale soon after it is displayed, continued scale build-
up could damage the Brewer. If this occurs, “DE-SCALE” will begin to blink to alert  you to the potential damage to the Brewer if you do not de-scale immediately.
M E N U
B R E W
M E N U
DE-SCA
LE
RE A DY
TO  B R E W
fig. 20
De-Scaling Instructions
A. PREPA RE 
Step 1:    Make sure you have at least 48 ounces of undiluted white vinegar   
on hand. You will also need an empty sink and a large ceramic mug  (do not use a paper cup). 
Step 2: Empty the water in the Water Reservoir.
Step 3: Disable “Auto Off” features. 
B.  FILL A ND CLE A N 
Step 1:    Pour the vinegar into the Water Reservoir to fill it.
Step 2:   
Place a large mug on the Drip Tray Plate and run a water brew cycle. 
DO NOT USE A K-CUP, just select the Large Mug brew size. Pour the 
contents of the large mug into the sink.
Step 3:   
Repeat the brew process 3 times.
Step 4: Now let the Brewer stand for at least 4 hours while still on.
C.  RINSE 
Step 1: Ensure the Water Reservoir is filled with fresh water.
Step 2:    Place a large mug on the Drip Tray Plate and run a water brew cycle. 
Pour the contents of the large mug into the sink.
Step 3: Repeat brew process until the Water Reservoir is empty. 
Step 4:    You may need to perform additional water brew cycles if you notice 
any residual taste.
NOTE : If “DE-SCALE” is still displayed on the LCD Control Center after 
completing the procedure, repeat the de-scaling procedure above.
Service
Beyond these recommended cleaning and maintenance procedures this 
Brewer is not user serviceable. For service, please refer to the Warranty 
section of this guide. 
Storage 
Empty the Water Reservoir before storing, and take care to ensure that you 
store your Brewer in a safe and 
frost free environment. Please be sure to 
store your Brewer in its 
upright position to avoid water leakage from the inner 
tank. If you store the Brewer in a cold environment, you run the risk of water 
freezing inside the Brewer and causing damage. When you prepare to use it 
after storage, we recommend rinsing the Water Reservoir with fresh water 
and running three cleansing brews without a K-Cup.
If you plan to move your Brewer to a different location, turn the Brewer   
off, unplug it, and empty the Water Reservoir. If your Brewer has been in   
an environment below freezing, please be sure to let it warm to room   
temperature for at least 2 hours before using.
Transport Brewer in the upright position to ensure inner tank does not leak  through vent.
14 15   
						

							SECTION 5  Warranty
Limited One Year Warranty 
Keurig® warrants that your Brewer will be free of defects in materials or 
workmanship under normal home use for one year from the date of purchase. 
It is recommended that you fill out and return the warranty card enclosed  with your Brewer so that your purchase information will be stored in our 
system. Keurig will, at its option, repair or replace the Brewer without charge  upon its receipt of proof of the date of purchase. If a replacement Brewer is necessary to service this warranty, the replacement Brewer may be new or 
reconditioned. If a replacement Brewer is sent, a new limited one year  warranty will be applied to the replacement Brewer.
This warranty only applies to Brewers operated in the United States and  Canada. This warranty gives you specific legal rights, and you may also have 
other rights that vary from state to state and, in the case of Canada, from  province to province.
What is not covered by the Limited Warranty?
THIS WARR ANT Y DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL  DAMAGES SUCH AS PROPERT Y DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND E XPENSES RESULTING FROM ANY BRE ACH   
OF THIS WARR ANT Y, E VEN IF FORESEE ABLE. Some states or provinces 
do not allow the exclusion or limitations of incidental or consequential 
damages, so the above limitation or exclusion may not apply to you   
depending on the state or province of purchase. 
Nor does this warranty cover damages caused by services performed by 
anyone other than Keurig or its authorized service providers, use of parts 
other than genuine Keurig parts, or external causes such as abuse, misuse,  inappropriate power supply or acts of God.
Other Limitations
THIS WARRANT Y IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS  WARRANT Y, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCL AIMS ALL OTHER WARRANTIES WITH RESPECT TO 
YOUR B70 BREWER, INCLUDING ANY IMPLIED WARRANT Y OF MERCHANT  ABILIT Y OR FITNESS FOR ANY PARTICUL AR PURPOSE. Some states or  provinces do not allow disclaimers of such implied warranties or limitations 
on how long an implied warranty lasts, so the above limitation may not apply  to you depending on the state or the province of purchase. 
How do you obtain warranty service?
Keurig Brewers are high-quality appliances and, with proper care, are   
intended to provide years of satisfying performance. However, should the 
need arise for warranty servicing, simply call Keurig Customer Service at 
our toll free phone number 1.866.901.BREW (2739). Please do not return your  Brewer for servicing without first speaking to Keurig Customer Service to 
obtain an Authorization to Return number (ATR). Keurig Brewers returned   
without an ATR number will be returned to the sender without servicing.
Keurig, Incorporated  55 Walkers Brook Drive 
Reading, MA 01867 
1.866.901.BREW (2739)
17
SECTION 4  Troubleshooting
16
Situation 
Brewer does not  have power
Brewer will not brew
Chlorine or mineral  taste in coffee
Solution 
• Plug Brewer into an independent outlet.• Check to be sure that it is plugged in securely. • Plug into a different outlet. • Reset your home’s circuit breaker if necessary.•   Make sure that the Power Switch has been 
turned on and LCD lights are illuminated.
•   
After placing the K-Cup® in the K-Cup Holder, make 
sure the Handle is pushed down securely and the  LCD Control Center reads “READY TO BREW” with the Left, Right and BREW Butt ons flashing, then 
press the Left, Right or BREW Button.
•   
If the LCD Control Center indicates “ADD 
WATER”, add water to the Water Reservoir or 
make sure the Water Reservoir is seated properly  in its base.
•   
If the LCD Control Center indicates “ADD WATER” 
even after refilling, contact Customer Service at 
1.866.901.BREW (2739).
•   
The Exit Needle may be clogged (refer to page 14).
•  
Consider using bottled water, filtered water 
or the Keruig® Water Filter Starter Kit 
(available at www.keurig.com). 
    
Situation 
Brewing a partial cup
 
The time is not   
displayed on the LCD  Message Center
Brewer shuts   
off or turns on   
automatically
The blue light in Water  Reservoir is flashing
Solution 
•  
The Exit Needle may be clogged (refer to page 14).•  
Clean the K-Cup Holder Assembly if necessary 
and rinse under faucet (refer to page 13).
•   
The Water Reservoir may have been removed 
during brewing. Replace the Water Reservoir   
and perform a water brew without a K-Cup.
•   
“De-Scale” the Brewer (refer to page 14 ).•  
If you have repeated the de-scale procedure on 
your Brewer two times and it is still only brewing   
a partial cup, contact Customer Service at   
1.866.901.BREW (2739).
•   
The time will not be displayed on the LCD 
unless you have set it. To set the clock, follow the procedure on page 10.  
•  
If power is interrupted to the Brewer, you will 
need to set the clock again using the procedure 
on page 10.
•   
Check to make sure that the Auto Off timer 
and/or On/Off time features have not been set. To 
do this, press the MENU Button below “MENU”  and scroll through the programming options. 
“OFF” should be displayed for Auto Off timer and  On/Off.  If “OFF” is not displayed, follow 
directions on page 11 to reset.
•   
The water level is low and a full cup cannot be 
brewed. Add water to Water Reservoir
If any problems persist, contact Customer Service at 1.866.901.BREW (2739) 
						

							19
18
TABLE DES MATIÈRES
SYSTÈME D’INFUSION GOURMET UNE   
TASSE À LA FOIS DE KEURIG® 
Platinum B70 — Comment utiliser votre cafetière
RÉGL aGES
Conseils utiles  ...................................................................................20Déballage  ...........................................................................................20Caractéristiques  ...............................................................................21
SECTION 1  —  PRÉPARATION ET PREMIÈRE INFUSIONPréparation et première infusion  ...................................................22
SECTION 2  —  COMMANDES ET VOYANTSRéglage de l’horloge  ........................................................................26Programmation des fonctions de mise   
en marche et d’arrêt automatiques  ...............................................26Réglage de la température d’infusion  ...........................................28Programmation du format de tasse  ..............................................29
SECTION 3  —  NETTOYAGE ET ENTRETIENNettoyage  ...........................................................................................29Détartrage   .........................................................................................30Entreposage  .......................................................................................31
SECTION 4  —  DÉPANNAGE ...............................................................32
SECTION 5   —  GARANTIE ..................................................................33
 
Inscrivez le numéro de série de votre cafetière ici.
Le retrait de l’étiquette du numéro de série annulera la garantie.
18
Lors de l’utilisation de tout appareil élec -
trique, des mesures de sécurité de base 
devraient être suivies, et notamment :
1. Lire toutes les instructions avant l’utilisation. 
2.   Ne pas toucher les surfaces chaudes. Utiliser 
les poignées s’il y en a. 
3.  Installer correctement l’appareil et le placer 
dans un endroit conforme aux présentes 
instructions avant de l’utiliser. 
4.   L’utilisation d’accessoires non recommandés 
par le fabricant de l’appareil risque de causer 
des incendies, des chocs électriques ou des 
blessures. 
5.  Éviter le contact ou la proximité de l’appareil 
avec un élément électrique ou un brûleur à 
gaz. Éviter également de placer l’appareil à 
l’intérieur d’un four chaud. 
6. Ne pas utiliser à l’extérieur. 
7.  Pour éviter les risques d’incendie, de chocs 
électriques ou de blessures, ne pas immerger 
la fiche, le cordon d’alimentation ou l’appareil 
dans l’eau ni dans aucun autre liquide. 
8. Ne pas trop remplir le réservoir d’eau. 
9.   Utiliser  seulement de l’eau  dans cet appareil! 
Ne verser aucun autre liquide ou aliment dans 
le réservoir d’eau à l’exception des produits 
mentionnés dans les instructions de nettoyage 
du présent manuel. 
10.    Éteindre et débrancher l’appareil avant de 
le nettoyer ou d’en faire l’entretien. Laisser 
l’appareil refroidir avant d’ajouter ou d’enlever  des pièces et avant de le nettoyer. 
11. 
    Pour une utilisation optimale, brancher 
l’appareil dans une prise de courant séparée 
sur un circuit spécialisé pour éviter que les 
lumières vacillent, que les fusibles sautent ou 
que les disjoncteurs se déclenchent. 
12.   Ne jamais utiliser un appareil dont la fiche ou 
le cordon d’alimentation est endommagé ou 
un appareil qui présente un trouble de fonc -
tionnement ou qui a été endommagé. Commu -
niquer avec le Service à la clientèle de Keurig
® 
pour signaler tout mauvais fonctionnement de 
la cafetière ou tout dommage à celle-ci.
13.   Ne pas laisser le cordon d’alimentation pendre 
d’une table ou d’un comptoir ni entrer en con -
tact avec une surface chaude. 
14.   Pour débrancher la cafetière, appuyer sur 
le bouton de mise en marche (POWER) situé 
sur la cafetière pour éteindre l’appareil, puis 
retirer le cordon de la prise. 
15.   Ne jamais laisser des enfants utiliser la cafetière 
ni rester à proximité sans surveillance. 
16.    Ne pas soulever la poignée pour ouvrir le cou -
vercle de la cafetière durant l’infusion. 
17.   
Toujours laisser le couvercle sur le réservoir 
d’eau, sauf lors du remplissage. 
18.   L’appareil est équipé d’un cordon 
d’alimentation muni d’un fil et d’une prise 
de mise à la terre. L’appareil doit être mis à 
la terre en utilisant une prise de courant à 
contact de mise à la terre à trois trous. En cas  de court-circuit, la mise à la terre réduit les 
risques de chocs électriques. 
19.  
 Si la prise de courant est une prise de courant 
murale standard à deux trous, le propriétaire 
a l’obligation et la responsabilité de la faire 
remplacer par une prise de courant de mise à 
la terre à trois trous.
 20.   Il ne faut en aucun cas couper ou enlever 
la troisième broche (mise à la terre) de la 
fiche du cordon d’alimentation, ni utiliser un 
adaptateur. 
21.   Consulter un électricien qualifié si les 
instructions sur la mise à la terre ne sont pas 
parfaitement comprises ou en cas de doutes 
sur la mise à la terre de l’appareil. 
22.  Ne pas utiliser l’appareil pour une fin autre 
que celle pour laquelle il a été conçu.
CONSER vER CE 
M aNUEL.
RÈGLES DE SÉCURITÉ IMPORTANTES   
Fonctionnement et utilisation sans danger
av ERTISSEMENT  aUX UTILIS aTEURS ET  aUX P aRENTS 
1. NE  permettez  PaS  aux enfants d’utiliser l’appareil sans 
la supervision d’un adulte. L’appareil distribue de l’eau 
très chaude.
2.  av IS SPÉCI aL  aUX UTILIS aTEURS DE C hOCOL aT 
C ha UD :  aPRÈS L’UTILIS aTION D’UN GODET K-CUP 
DE C hOCOL aT C haUD, L aNCEZ IMMÉDI aTEMENT  UN 
CYCLE  D ’INFUSION  D ’E aU  C ha UDE  sans K-Cup pour 
éviter une possible obstruction de l’aiguille de sortie.  NE 
tenez  PaS  pour acquis que le prochain utilisateur le fera. 
ATTENTION : Le godet K-Cup® est perforé par deux aiguilles, une au-dessus du 
support à K-Cup et l’autre au fond du support à K-Cup. Pour éviter tout risque de 
blessure, ne pas mettre les doigts dans le compartiment de la K-Cup.
ATTENTION : L’eau se trouvant dans le support à K-Cup durant l’infusion est 
extrêmement chaude. Pour éviter tout risque de blessure, ne pas soulever la 
poignée ni ouvrir le boîtier du support à K-Cup durant l’infusion.
INSTRUCTIONS POUR CORDON D’ALIMENTATION COURT :
 L’appareil est doté 
d’un cordon d’alimentation court pour éviter qu’il s’emmêle ou que quelqu’un 
trébuche sur un cordon long.
Si une rallonge est utilisée, (1) les caractéristiques électriques inscrites sur 
la rallonge doivent égaler ou excéder celles de l’appareil, (2) le cordon doit 
être fixé de façon à ce qu’il ne pende pas d’une table ou d’un comptoir pour 
éviter qu’un enfant puisse le saisir ou que quelqu’un trébuche et (3) la ral -
longe doit être munie d’une prise de mise à la terre à trois broches.
CE PRODUIT EST DESTINÉ À UNE  UTILISATION DOMESTIQUE SEULEMENT 
AVERTISSEMENT CE PRODUIT CONTIENT DES PRODUITS 
CHIMIQUES, NOTAMMENT DU PLOMB, UN MÉTAL QUI, SELON L’ÉTAT DE 
LA CALIFORNIE, CAUSE LE CANCER, DES ANOMALIES CONGÉNITALES OU 
D’AUTRES MALFORMATIONS GÉNÉTIQUES.
AVERTISSEMENT
AVERTISSEMENT : POUR RÉDUIRE LES RISQUES 
D’INCENDIE ET DE CHOCS ÉLECTRIQUES, NE PAS RETIRER 
LE COUVERCLE INFÉRIEUR. CET APPAREIL NE CONTIENT 
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR. LES 
RÉPARATIONS NE DEVRAIENT ÊTRE EFFECTUÉES QUE 
PAR UN TECHNICIEN DE SERVICE AGRÉÉ.
RISQUE D’INCENDIE ET DE 
CHOCS ÉLECTRIQUES
NE PAS OUVRIR!
!