Keurig B 70 Owners Manual

							Owner’s manual
Platinum B70 Keurig® Brewer 
						

							3
TABLE OF CONTENTS
KEURIG® GOURME T SINGLE CUP HOME BRE WING SYSTEMPlatinum B70 — Using Your Brewer
S E T- U P  
Helpful Hints  ........................................................................\
................
4 
Unpacking  ........................................................................\
....................
4 
Features  ........................................................................\
.......................
5
SECTION 1 — SET-UP & FIRST BRE W  
Set-Up & First Brew ........................................................................\
...6
SECTION 2 — CONTROLS & INDICATORS  
Setting the Clock ........................................................................\
.......10 
Programming On/Off Features  ......................................................10 
Programming Brew Temperature  .................................................12 
Programming Brew Size .................................................................13
SECTION 3 — CLEANING & MAINTENANCE  
Cleaning ........................................................................\
......................13 
De-Scaling ........................................................................\
..................
14 
Storage  ........................................................................\
.......................
15
SECTION 4 — TROUBLESHOOTING ..................................................16
SECTION 5   — WARRANTY ................................................................17
Record your Brewer Serial Number here.  See Unpacking Instr uctions on page 4 for serial number location.
2
Removing the serial number label from the Brewer will void warr ant y. 
CAUTION: There are two sharp needles that puncture the K-Cup® pack, one 
above the K-Cup® Pack Holder and the other in the bottom of the K-Cup® Pack 
Holder. To avoid risk of injur y, do not put your fingers in the K-Cup® Pack 
Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup
® Pack Holder during the   
brew  process. To avoid risk of injur y, do not lift the Handle or open the K-Cup®  
Pack  A ssembly Housing during the brewing process.
CAUTION:  Please always keep the Brewer in its upright position to avoid 
potential injury and/or damage to your Brewer.
SHORT CORD INSTRUCTIONS:
 A shor t power supply cord is provided to 
reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or 
extension cord should be at least as great as the electrical rating of the 
appliance; (2) the cord should be arranged so that it will not drape over the 
counter top or tabletop where it can be pulled on by children or tripped over 
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING 
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, 
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
WARNING:  TO REDUCE THE RISK OF FIRE OR 
ELECTRIC SHOCK, DO NOT REMOVE THE 
BOTTOM COVER. NO USER SERVICEABLE 
PARTS ARE INSIDE. REPAIR SHOULD BE DONE 
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR  
ELECTRIC SHOCK   DO NOT OPEN
!
IMPORTANT SAFEGUARDS  Safe Operation & Use
When using electrical appliances, basic 
safety precautions should be followed, 
including the following:
 1. Read all instructions before using.
 2.  Do not touch hot sur faces. Use handles   
and knobs when available.
 3. This appliance must be properly 
installed and located in accordance 
with these instructions before it is used.
 4. The use of accessor y attachments 
not recommended by the appliance 
manufacturer may result in fire, 
electrical shock or injur y to persons.
 5. Do not place on or near a hot gas or 
electric burner, or in a heated oven.
 6. Do not use outdoors.
 7. To protect against fire, electric shock 
and injur y do not immerse cords, plugs, 
or the appliance in water or any other 
liquid.
 8. Do not over fill the Water Reser voir   
with water.
 9. Use  only water  in this appliance! Do 
not put any other liquids or foods in the 
Water Reser voir except as instructed in 
the Cleaning Instructions in this guide.
 10.  Turn off and unplug the Brewer before   
cleaning or maintenance. Allow to cool   
before putting on or taking off par ts   
and before cleaning the appliance.
 11. For best operation, plug the appliance   
into its own electrical outlet on a 
dedicated circuit to prevent flickering 
of lights, blowing of fuses or tripping a 
circuit breaker.
 12 . Do not operate any appliance with a   
damaged cord or plug or after 
the appliance malfunctions or is 
damaged in any manner. Contact 
Keurig Customer Ser vice to repor t 
any malfunction of or damage to the 
B r e w e r.
 13. Do not let the cord hang over the edge 
of the table or counter, or touch hot 
surfaces.
 14 .  To disconnect, press the Power Button 
on the Brewer to “OFF” status and then 
remove the plug from the wall outlet.
 15. Close super vision is necessar y when 
any appliance is used by or near 
children.
 16. Do not lift the Brewer Handle while   
brewing is in progress.
 17. Always keep the Water Reser voir Lid   
on the Water Reser voir unless you are   
refilling it.
 18. This appliance is equipped with a power 
cord having a grounding wire with a   
grounding plug. The appliance must 
be grounded using a 3-hole properly 
grounded outlet. In the event of an  electrical shor t circuit, grounding 
reduces the risk of electrical shock.
 19. If the outlet is a standard 2-prong wall 
 
outlet, it is your personal responsibility   
and obligation to have it replaced with a 
properly grounded 3-prong wall outlet.
 20. Do not, under any circumstances, cut or 
remove the third (ground) prong from 
the power cord or use an adapter.
 21.  Consult a qualified electrician if 
the grounding instructions are not 
completely understood, or if doubt 
exists as to whether the appliance is 
properly grounded.
 22. Do not use the appliance for other than 
its intended use.
S av E T HE SE  
I NSTRUCTIONS.
W aRNING TO USERS a ND PaRENTS
1. DO NOT permit children to use Brewer   
unless there is adult super vision. Brewer   
dispenses ver y hot water.
2. SPECI aL NOTICE FOR HOT COCO a USERS:  
IMMEDI aTELY a FTER USING a HOT COCO a  
K-CUP
® P a CK, RUN a Hot Water Brew Cycle  
without a K-Cup® pack to avoid the possibility   
of clogging the exit needle. DO NOT assume   
the next user will do this.     
						

							Set-Up
5
Features  Platinum — Model B70 Brewer
 A.  Water Reser voir Lid B. Easy-Fill Lid C. Water R eser voir D. Water Reser voir   
Lock Tab Slot
 E.  Handle
Platinum B70 Brewer Controls 
 
and Indicators
Helpful Hints 
  1.  Plug Brewer into its own grounded outlet.  If the electric circuit is overloaded with other   
appliances, your Brewer may not function   
properly. The Brewer should be operated on   
its own circuit, separate from other appliances.
  2.  Keep your Brewer turned “ON.”   To brew a fresh cup of coffee, tea or hot cocoa  
any time you want, keep your Brewer turned 
“ON” all the time. However, the Brewer is fully  programmable so you can set it to turn on and off automatically to match your schedule.   
Or, if you prefer, set the Brewer to automatica lly 
turn off after a period of time. Follow the simple  instructions on pages 10–13 to find the settings 
that are most convenient for you.
  3.  For the best tasting gourmet coffee, tea or  
hot cocoa, Keurig recommends using bottled  
or filtered water. 
 
Water quality varies from place to place.   
If you notice an undesirable taste in your cup   
of coffee, such as chlorine or other mineral 
tastes, we recommend you consider using  bottled water or water from a filtration 
system. For best results, carefully follow  manufacturer’s instructions when using any 
water filtration system.
  4.  Customize the size, flavor & brew that’s   
perfect for you.  
With the choice of over 200 varieties of K-Cup® 
packs and 5 brew sizes (Extra-Small Cup-  
3.25 oz., Small Cup-5.25 oz., Small Mug-  
7.25 oz., Large Mug-9.25 oz., and Travel  Mug-11.25 oz.), your Keurig
® Brewer gives you 
endless options to customize the size, flavor 
and brew that’s per fect for you. For a strong, 
intense cup, select an Extra Bold K-Cup
® pack 
(with up to 30% more ground coffee than  regular varieties) and brew the size that’s right 
for you. The smaller the brew size, the more  intense flavor in your cup. The larger the brew 
size, the less intense flavor in your cup.
  5.  Remove K-Cup® pack after use.  Please see page 7 for brewing instructions. 
 6.  Brewing into a travel mug.  To brew into a travel mug, simply remove the  
Drip Tray A ssembly and place the travel mug  
on the Drip Tray Base.
  7.  De-scale Brewer regularly.   Please see pages 14 and 15 for instructions.
Unpacking Instructions
 1. Place Brewer box on a large steady sur face  
(such as a table or counter top) or on the floor.  Open the box.
 2.  Remove enclosed literature.
  3. Turn the box on its side with front of box   
face down.
 4. Reach into the box and grasp the plastic bag   
that contains the Brewer.
 5. Carefully pull the plastic bag (and packaging 
materials) toward you and out of the box. The 
Brewer will still be encased in the poly foam   
and be on its side.
 6. Remove the top poly foam packaging material.
 7.  Carefully lift Brewer off of the bottom poly foam 
and place it upright on a flat, steady sur face.
  8. Lift plastic bag off of Brewer.
 9.  Record the serial number for this Brewer on 
page 3 of this guide. The serial number can be 
found on the bottom of the Brewer box or on the  Brewer behind the Drip Tray (when removed).
 10.  Place the Brewer upright on a flat, steady 
surface. Remove tape holding Water Reser voir  in place. 
We recommend you save all packing materials in  case future shipping of the product is necessar y.
WARNING:   
Keep all plastic bags away  
from children.
4
a
C
B
D
J
M
L
K
I
N
F
G
U
S
T
QE
H
P
O
R
 Q.  LCD Control Center R. Left Button S. Right Button T. MENU Button U. BRE W Button
 F.  Funnel G. K-Cup® Pack Holder   
(F and G are the K-Cup® 
Pack Holder Assembly) 
 H.  Lid
 I. K-Cup® Pack   
Assembly Housing
 J.  Housing K. Drip Tray Plate L. D r i p  Tr a y
 M. Drip Tray Base N. Vent O. Power Cord P. Power Switch (not 
shown) Located Rear 
Right Side of Brewer       
						

							Setting Up Your Brewer
 1. Unwrap cord and plug the Brewer into a 
grounded outlet. Remove all pieces of   
packing tape and clear plastic sticker from   
LCD Control Center.
 2.  Place a large mug (10 oz. minimum) on the Drip 
Tr a y  P l a t e .
  3. Remove the Water Reser voir from Brewer by 
first removing Lid from the Water Reser voir   
(fig. 1), then lifting the Water Reser voir straight 
up and toward front of Brewer (may be tight),   
(fig. 2 A). Rinse with fresh water.
 4.  Fill Water Reser voir with bottled or filtered water 
so that the water level is just below the top edge 
of the Water Reser voir.
 5.  Place Water Reser voir base into the left side of the Brewer and be sure 
the Water Reser voir Lock Tab engages with the Brewer. Replace Lid on 
Water Reser voir. 
NOTE: Please ensure the Water Reser voir is seated 
properly, so that the back of the Water Reser voir is flush with the Brewer  (fig. 2 B and C). 
L o c k Ta b
Seated Properly
 6.
  Press and release the Power Switch found 
directly behind the right side of the Brewer.  Switch is spring loaded and will return to 
original position.
 7.  The blue LCD Control Center will come on and 
indicate “NOT RE ADY.” 
NOTE: A K-Cup® pack 
should not be used for this sequence
.
  8. The Brewer will automatically fill the internal 
tank with water and then the water will be 
heated. This will take about 4 minutes.   
During the heating period, “NOT RE ADY”   
is indicated on the LCD Control Center (fig. 3).   
Do not lift Brewer Handle during this heating 
period.  Once the water is heated, “RE ADY TO 
BRE W” will be indicated and the BRE W Button  will be illuminated (fig. 4). 
NOTE: You may see 
SECTION 1  Set-Up & First Brew
 5. Place a K-Cup® pack in the K-Cup® Pack 
Holder (fig. 6). 
CAUTION:  There are two sharp 
needles that puncture the K-Cup® pack, one 
above the K-Cup® Pack Holder and the other in 
the bottom of the K-Cup® Pack Holder. To avoid 
risk of injur y, do not put your fingers in the  K-Cup
® Pack Assembly Housing.
 6. 
Lower the Handle to close the Lid over the  
K-Cup® Pack Holder. (When it is closed 
completely, the LCD Control Center will  indicate “RE ADY TO BRE W.” The Left and 
Right Buttons will be lit and the BRE W Button  will flash up to 60 seconds.)
 
a.  All brew size icons are lit with the default   
size flashing (fig. 7). To choose a different size,   
press Left Button to go down in size or Right  Button to go up in size. 
NOTE: The Small Mug is 
the factor y set default brew size. To program 
your favorite brew size se e page 13 
“Pro gramming Your Brew Size.”
 b.
  Your choices are a stronger Extra-Small   
Cup (3.25 oz. ser ving), a Small Cup (5.25 oz. 
ser ving), a Small Mug (7.25 oz. ser ving), a  Large Mug (9.25 oz. ser ving) or a Travel Mug 
(11.25 oz. ser ving).
small amounts of water coming from the Vent 
and dripping into the Water Reservoir during  this and subsequent heating  — this is normal.
 9.
  Lift and lower the Handle. Press the flashing 
BRE W Button to star t a cleansing brew without a K-Cup
® pack. Pour the hot water 
into the sink. 
NOTE: A K-Cup® pack should not 
be used for this sequence
.
 10.  The one-time set-up process is now   
complete and you are ready to brew!  
NOTE: The Brewer may take 15-30 seconds   
between brews and then “RE ADY TO BRE W”   
will be indicated.
Ready to Brew Your First Cup
 1.  LCD Control Center will indicate   
“READY TO BREW.” 
 2. Place a cup or mug on the Drip Tray Plate.
  3. Lift the Handle and the K-Cup® Pack   
Holder will open toward you (fig. 5).
 4. Select a K-Cup® pack.   NOTE:  Do not remove the foil   
lid or puncture the K-Cup® pack.
MENU
BREW
MENU
R
EAD Y
NOT
IMPORT aNT: You cannot use your Keurig® Brewer until it has been set 
up for its first use.
NOTE:  If Brewer has been exposed to temperatures below freezing, 
allow Brewer at least two hours to reach room temperature before 
brewing. A frozen or extremely cold Brewer will not operate.
MENU
BREW
MENU
R
EAD Y
TO  B REW
fig. 3
fig. 4
fig. 6
fig. 1
fig. 5fig. 7
67
fig. 2
aB
Not Seated Properly
C                                                                                                                                                                    
						

							89
 c. Once size is chosen, press BRE W Button. 
BRE W Button will stop flashing, Left and Right 
Buttons will no longer be lit and icon   
of brew size will be lit.
 7.  The LCD Control Center will now indicate 
“BRE WING” and the cup size you selected will  be illuminated on the LCD Control Center   
(fig. 8). 
CAUTION: There is extremely hot water 
in the K-Cup® Pack Holder during the brew 
process. To avoid risk of injur y, do not lift the  Handle or open the K-Cup
® Pack Assembly 
Housing during the brew process.
  8.
 There may be a shor t pause prior to coffee   
being dispensed. The entire brew process   
lasts for approximately 1 minute and ends   
with a burst of air to remove all liquid from   
the K-Cup
® pack.
 9.  Lift the Handle, 
remove and dispose of the used K-Cup
® pack. 
CAUTION: K-Cup® 
pack will be hot.
 10.
  Enjoy your first cup   
of Keurig Brewed®   
gourmet coffee, tea   
or hot cocoa!
 11.  Your Brewer may indicate “NOT RE ADY” as it heats water for the next  
brew cycle. The “RE ADY TO BRE W” indication will return to the LCD 
Control Center in about 15 seconds.
 
Stopping the Brew Process
If you need to stop the brewing after the process has star ted, press and 
release the Power Switch to turn the Brewer “OFF.” The flow of coffee, tea 
or hot cocoa will stop, the heating element will shut off and the blue lights  illuminating the LCD Control Center and Water Reser voir will disappear.  
NOTE: You may get more coffee, tea or hot cocoa in your cup during your next 
brew. We recommend that you per form a cleansing brew after a terminated 
brew. Then your NE X T brew will be the volume you have selected.
adding Water
The LCD Control Center will indicate “ADD  WATER” when the water level in the tank is  low or if the Water Reser voir has been removed 
(f ig. 9). The blue light in the Water Reser voir will 
also blink when water needs to be added. The  Brewer will not allow you to brew when “ADD WATER” is indicated (fig. 9). 
SECTION 1Set-Up & First Brew (continued)
The Water Reser voir can be filled in two ways. 
 1.  
Open the Easy-Fill Lid and pour water directly into the Water Reser voir   
while it is still attached to the Brewer, then close the Lid. The entire   
Water Reser voir Lid may be removed completely, if preferred.
 2.  Remove the Water Reser voir from Brewer by first removing Lid from the 
Water Reser voir, then lifting the Water Reser voir straight up and toward front of Brewer. Fill with water. Place the Water Reser voir back on the 
Brewer and replace the Lid. 
IMPORTANT : Do not remove the Water 
Reser voir during the brewing process.
Brewing Iced Beverages
Your iced tea and iced coffee taste best when fresh-brewed hot over ice.  
Tr y it by placing a tall cup filled with ice on the Drip Tray Plate (the Drip Tray  A ssembly can be removed to accommodate taller cups), choose your favorite K-Cup
® pack, select the brew size and press the BRE W Button. Also, look for 
the Brew Over Ice™ icon on K-Cup® packs specially crafted to brew over ice! 
IMPORTANT:  Do not brew into a cup made of glass. Doing so may cause the   
glass to crack or break.
Brewing Hot Water
Your Brewer is able to produce hot water for making hot cocoa from a packet,   
for use in cooking, for making soups, etc. Simply follow the instructions on   
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup
® pack. 
NOTE:  After brewing a hot cocoa K-Cup® pack, we recommend running a 
cleansing brew without a K-Cup® pack.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge  the water from the inner tank.
 1.  If there is water in the Water Reser voir, remove the Lid, then lift the   
Water Reser voir straight up and away from Brewer. Discard water, rinse 
and refill with water. Place the Water Reser voir back on the Brewer and  replace the Lid. (If there is no water in the Water Reser voir, simply refill.)
 2.  Be sure the Brewer is turned on. Raise and lower the Handle on the 
Brewer without inser ting a K-Cup® pack.
  3. The LCD Control Center will indicate “RE ADY TO BRE W.” Brew a Travel 
Mug (11.25 oz. ser ving) of water (do not use a K-Cup® pack). 
 4.  Repeat steps 2 and 3 t wo more times to completely purge water from   
inner tank.
If you are experiencing any problems with your Brewer, please contact   
Customer Ser vice at 1.866.901.BRE W (2739).
 
Small Cup(5.25 oz.) 
Small Mug(7.25 oz.)
Large Mug(9.25 oz.) 
Travel Mug(11.25 oz.)
Extra-Small Cup(3.25 oz.) 
MENU
BREW
MENU
B
REW IN G
fig . 8
MENU
BREW
MENU
ADD
WATER
R EAD Y
NOT
fig . 9     
						

							11
10
SECTION 2  Controls & Indicators (LCD Control Center)  b.  Press or hold the Left Button under the 
blinking “H” to advance 1 hour at a time, up   
to 9 hours. 
  c.   After setting the desired Auto Off time, press 
the MENU Button five times to scroll through 
the remaining programming options and exit 
the programming mode. “AUTO OFF SE T”   
(fig. 12) will now be displayed to indicate that it  has been set. 
  d.   To cancel the Auto Off feature, press the 
MENU Button t wice to reach the “AUTO OFF” 
programming mode. Press and release the  Left Button under the blinking “H” to advance 
one hour at a time until “OFF” is indicated.
  3.   Program your Brewer for a specific On/Off  
Time.
 NOTE: To use this programming feature, 
the clock must be set to the correct time. The 
clock will not be displayed unless the time is set.
  a.   After setting the correct time (required), press 
the MENU Button three times to program On 
Time feature. The LCD Control Center will  show the programming options with a small arrow next to “SE T ON TIME” (fig. 13). 
  b.   Press or hold the Left Button under the “H”   
to scroll through the hours to your desired 
“ON TIME” hour.
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the 
LCD Control Center. 
NOTE:  You must set the clock if you will be using the Auto 
On/Off Time programming feature.
 1. 
Press the MENU Button.
 2. The word “OFF” will appear at the top of the 
LCD Control Center to indicate that the clock is not set (fig. 10). The programming options will appear on the LCD Control Center with a 
small arrow pointing to “SE T CLOCK.”   
“H” (Hour) will appear above the Left Button  and “M” (Minute) will appear above the Right Button. The “H” and “M” icons and Left and 
Right Buttons will flash.
  3. Press or hold the Left Button under the 
flashing “H” until you have reached the 
appropriate hour. If the hour has passed   
12 “PM” will be shown.
 4.  Press or hold the Right Button under the 
flashing “M” to set the minutes.
 5.  When you have reached the correct time, press the MENU Button six 
times to scroll through the remaining programming steps.
Set
Hours Set
Minutes
MENU
BREW
MENU
SET 
CLOCK
AUTO OFF 
  ONOFF TIME 
BREW TEMP 
BREW SIZE
M
H
fig . 10
 6. The correct time should now be displayed in the LCD Control Center.  
NOTE: If power is interrupted to the Brewer by unplugging it, or if power is 
lost, follow the procedure above to reset the time as the clock will not be 
visible until the time is set. Brew size and brew temperature menu settings 
are remembered and restored automatically. All other settings will be  restored automatically after clock is set.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea  or hot cocoa on your own schedule. By programming your Brewer to turn on 
each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee. It will take the Brewer approximately 4 minutes to  warm up from room temperature.
  1.  Leave it ON all the time. The Brewer can be left on all the time so that it is 
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To  turn the Brewer off at any time, simply press and release the Power 
Switch. 
( NOTE :
 Although the clock remains on, if set, you can not brew a cup 
of coffee, tea or hot cocoa.) 
Press and release the Power Switch again to 
restore power to the Brewer. You will have to wait for the water to heat up  before the Brewer is ready to brew.
 2.  Set the Brewer to “AUTO OFF” following a specified period of time after the 
last brew.  
 a.  Press the MENU Button t wice to program the Auto Off feature. The LCD 
Control Center will now di splay the programming options with a small 
arrow next to “SE T AUTO OFF” (fig. 11).  
c.  Press or hold the Right Button under the “M” 
to scroll through the minutes to your desired 
“ON TIME” minutes.
  d.  After setting the des ired time, press the 
MENU Button to save the “ON TIME” and   
move to the “SE T OFF TIME” (fig. 14). 
  e.  If you want to set an “OFF TIME,” repeat the 
procedure above in steps b & c to set your 
desired “OFF TIME” (fig. 14). 
  f.  To complete the process, press the MENU 
Button three more times to exit the 
programming mode. The Control Center   
will now indicate the options you have set.
  g.  The Auto On time and Auto Off time functions 
operate independently from one another. To 
cancel either set function, follow the steps  above and use the “H” and “M” Buttons to 
advance to 12:00 AM. Make sure the “M” Button is set to :00, then change the “H” 
Button. When you reach 12:00 AM, the   
Control Center will indicate “OFF” and the  function will be disabled.
   EXAMPLE : If you chose to set the On Time at 
6:55 AM and the Off Time for 10:00 PM, then  the Brewer will be “RE ADY TO BRE W” and 
maintain hot water in the tank during that   
time so that it is always ready for you to brew. 
If you wanted to brew outside this window,   
fig. 11
MENU
BREW
MENU
AUTO 
OFF SET
READ Y
TO  B REW
fig . 12
Set
Hours Set
Minutes
MENU
BREW
MENU
CLOCK
  AUTO OFF 
SET  ON TIME 
BREW TEMP 
BREW SIZE
M
H
fig . 13
Set
Hours Set
Minutes
MENU
BREW
MENU
CLOCK
  AUTO OFF 
SET OFF TIME 
BREW TEMP 
BREW SIZE
MPMH
fig . 14  
						

							13
simply press the Power Button and you can brew as soon as the water is heated and the 
“RE ADY TO BRE W” indicator is displayed on   
the LCD Control Center. 
NOTE :
 The On time and 
Off time functions operate independently fro m 
one another. To cancel either function, follow the  steps above and use the “H” and “M” Buttons to 
advance to 12:00 AM. When you reach 12:00 AM,  the Control Center will indicate “OFF” and the 
function will be disabled (fig. 15).
NOTE:  The Auto Off timer and the On/Off Time 
programming options operate independently,  
but can also be programmed to work together. 
For example, you can set the On Time function to  turn on at 7:00 AM and then set the Auto Off timer 
function to turn off the Brewer two hours after  the last brew.
SECTION 3  Cleaning & MaintenanceSECTION 2Controls & Indicators (LCD Control Center)
12
fig . 15Programming Brew Temperature (187°  – 192º F)
The Brewer brews at a preset temperature of 192°. You can adjust this 
temperature down by 5 degrees if you prefer a cooler cup of coffee, tea   
or hot cocoa. Simply follow the instructions below.
 1.  Press the MENU Button on the LCD Control 
Center five times to program the Brew 
Temperature feature.
 2.  The LCD Control Center will now display the 
programming options with a small arrow next to “SE T BRE W  TEMP” (fig. 16). Also, the 
temperature 192° (initial setting) will be 
displayed at the top of the LCD Control Center  to indicate the current temperature setting.
  3   . A minus sign will appear over the Left Button 
and/or a plus sign over the Right Button. Use  these Buttons to raise or lower the temperature 
one degree at a time.
 4.  Once you have reached your desired brew 
temperature, press the MENU Button twice to 
exit the programming mode. “BRE W TEMP SE T ”  will be indicated in the LCD Control Center if you 
have changed it from 192°.
MENU
BREW
MENU
 
CLOCK
AUTO OFF SET
  ONOFF TIME SET
SET BREW TEMP   BREW SIZE
-
-+
fig. 16
 5. To change the brew temperature again, repeat steps 1 through 3 to 
change the temperature up or down, remembering that the temperature 
can only be bet ween 187° and 192° . 
NOTE: At high altitudes (over 5,000 
feet), if boiling occurs, use the temperature adjustment (+0 and -5 degrees)   
to lower the temperature.
Programming Your Brew Size
    The Brewer is preset with the Small Mug   
(7.25 oz.) as the default brew size. The default  brew size allows the user to avoid scrolling through brew sizes if a par ticular size is   
chosen most often.
    To change the default brew size to your   
desired brew size:
 1.  Press the MENU Button six times.
 2. Using Left and Right Buttons, select your 
desired default brew size (fig. 17). 
  3. Once the desired default brew size is selected, 
press the MENU Button once to exit. Th e LCD 
Control Center will indicate the brew size set.
  CLOCK
AUTO OFF SET
  ONOFF TIME SET
 BREW TEMP 
SET BREW SIZE
fig . 17
Cleaning External Parts
Regular cleaning of the Brewer’s external components is recommended.
 1. Never immerse the Brewer in water or other liquids. The Housing   
and other external components may be cleaned with a soapy, damp,   
non-abrasive cloth.
 2.  The Drip Tray can accumulate up to 12 oz. of over flow. The Drip Tray   
and Drip Tray Plate should be periodically inspected and rinsed clean.   
To remove the Drip Tray A ssembly, simply slide it toward you, keeping it  level at all times to avoid spilling. The Drip Tray and Drip Tray Plate 
should not be placed in the dishwasher. They should be cleaned with a 
damp, soapy, non-abrasive cloth and rinsed thoroughly.  
Cleaning the K-Cup® Pack Holder assembly
 1.  Cleaning the Par ts  —The K-Cup® Pack Holder 
A ssembly can be placed onto the top shelf of a 
dishwasher. 
NOTE:  Use low temperature cycles in 
the dishwasher. 
To remove from the Brewer, 
open the cover by lifting the Handle. Grasp the  top of the K-Cup
® Pack Holder with one hand 
while push ing up on the bottom of the K-Cup® 
Pack Holder from underneath with the other 
until it releases (fig. 18). After cleaning, align the  K-Cup
® Pack Holder with the openi ng using the 
t wo front ribs as a guide, and snap into place 
from the top. 
fig . 18
Set
Hours Set
Minutes
MENU
BREW
MENU
SET 
CLOCK
AUTO OFF 
  ONOFF TIME 
BREW TEMP 
BREW SIZE
M
H                      
						

							 2.  Cleaning the Funnel —  The Funnel can be 
removed from the K- Cup® Pack Holder by 
pulling on it until it pops off (fig. 19). The Funnel  is dishwasher safe. To replace it, just snap it 
back onto the K-Cup
® Pack Holder Assembly.
  3.  Cleaning the Exit Needle —  The Exit Needle is 
located on the inside bottom of the K-Cup® Pack 
Holder A ssembly. Should a clog arise due to 
coffee grinds, it can be cleaned using a paper 
clip or similar tool. Remove K-Cup
® Pack Holder 
Assembly and detach Funnel. Insert the paper 
clip (fig. 19) into the Exit Needle to loosen the 
clog and push it o ut. The K-Cup
® Pack Holder is 
dishwasher safe. 
CAUTION : There are sharp
needles that puncture the K-Cup® pack above the K-Cup® Pack Holder and in 
the bottom of the K-Cup® Pack Holder. To avoid risk of injur y, do not put your 
fingers in the K-Cup® Pack Assembly Housing.
Cleaning the Water Reservoir & Water Reservoir Lid
The Water Reser voir Lid and Water Reser voir should be periodically  inspected and cleaned.
The Water Reser voir Lid or Water Reser voir should not be put into the  dishwasher. They should be cleaned with a damp, soapy, non-abrasive   
cloth and rinsed thoroughly. Do not dr y the inside of the Water Reser voir   
with a cloth as lint may remain. 
To clean the filter screen at the base of your Water Reser voir, empt y the  Water Reser voir and follow one or all of the following procedures.   
NOTE: If you are using a water filter inside the Water Reser voir, remove it 
before cleaning. 
SECTION 3Cleaning & Maintenance (continued)
!
fig . 19 1.  Rinse the filter screen with the strong force of water from your faucet. 
 2.  If you have a sprayer, aim the water spray at the filter screen. 
 3.  Fill the Water Reser voir with approximately t wo inches of clean water and 
agitate (shake) the Water Reser voir.
Empt y the Water Reser voir then fill it with clean water and return it to the 
Brewer. If needed, repeat above procedures. 
CAUTION:  Please rinse the Water 
Reser voir thoroughly after cleaning. This will ensure that no cleaners or cleaning  
solutions remain as they may contaminate the water supply in the Brewer.
De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the   
mineral content of the water in your area, calcium deposits or scale may   
build up in your Brewer. Scale is non-toxic, but left unattended, it can hinder  Brewer performance. De-scaling your Brewer helps maintain the heating element and other internal par ts of the Brewer that come in contact  with water. 
The Brewer should be de-scaled ever y 3-6  months to ensure optimal performance. It is 
possible for calcium deposits to build up faster, 
making it necessar y to de-scale more often.
You should promptly de-scale if “DE-SCALE” is  indicated on the LCD Control Center (fig. 20). 
However, even if “DE-SCALE” is not indicated,   
you should continue to de-scale your Brewer   
ever y 3-6 months. Properly follow the de-scaling  procedure described on page 15.
De-Scaling Instructions
A. PREPARE   
Step 1: To begin, you will need the following:  
  At least 4 8 oz. of undiluted white vinegar   
  Access to an empt y sink  
  A large ceramic mug (do not use a paper cup)
Step 2: Empt y the water from the Water Reser voir.
Step 3: Disable “Auto Off” features.  B. FILL AND CLE AN   
Step 1: Pour approximately 4 8 oz. of the vinegar into the Water Reser voir.
Step 2: Place a large mug on the Drip Tray Plate and run a cleansing brew.   
  DO NOT USE A K-CUP
® PACK, just press the BRE W Button. Pour  
  the contents of the large mug into the sink.
Step 3: Repeat the brew process without a K-Cup
® pack until “ADD WATER”   
  is indicated.
Step 4: Now let the Brewer stand for at least 4 hours while still on.
Step 5: Discard any residual vinegar and rinse the Water Reser voir thoroughly. C. RINSE   
Step 1: Ensure the Water Reser voir is filled with fresh water.
Step 2: Place a large mug on the Drip Tray Plate and run a cleansing brew.   
  Pour the contents of the large mug into the sink.
Step 3: Repeat brew process until “ADD WATER” is indicated. 
Step 4: You may need to per form additional cleansing brews if you notice  
  any residual taste.
NOTE: If “DE-SCALE” is still indicated after completing the procedure,   
repeat the de-scaling procedure above.
Service
Beyond these recommended cleaning and maintenance procedures, this 
Brewer is not user ser viceable. For ser vice, please refer to the Warranty 
section of this guide. 
Storage  
Empt y the Water Reser voir before storing, and take care to ensure that you 
store your Brewer in a safe and frost free  environment. Please be sure to 
store your Brewer in its upright position  to avoid water leakage from the 
inner tank. If you store the Brewer in a cold environment, you run the risk of  water freezing inside the Brewer and causing damage. When you prepare to 
use it after storage, we recommend rinsing the Water Reser voir with fresh  water and running three cleansing brews without a K-Cup
® pack.
If you plan to move your Brewer to a different location, turn the Brewer   
off, unplug it, and empt y the Water Reser voir. If your Brewer has been in   
an environment below freezing, please be sure to let it warm to room   
temperature for at least 2 hours before using.
Transpor t Brewer in the upright position to ensure inner tank does not leak  through vent.
14 15
fig. 20   
						

							SECTION 5  Warranty
Limited One Year Warranty 
Keurig, Incorporated warrants that your Brewer will be free of defects in 
materials or workmanship under normal home use for one year from the date 
of purchase. It is recommended that you fill out and return the warrant y card 
enclosed with your Brewer so that your purchase information will be stored  in our system. Keurig will, at its option, repair or replace a defective Brewer without charge upon its receipt of proof of the date of purchase. If a 
replacement Brewer is necessar y to ser vice this warranty, the replacement  Brewer may be new or reconditioned. If a replacement Brewer is sent, a new  limited one year warranty will be applied to the replacement Brewer.
This warrant y only applies to Brewers operated in the United States and  Canada. This warrant y gives you specific legal rights, and you may also have 
other rights that var y from state to state and, in the case of Canada, from  province to province.
Only the use of Keurig Brewed
® K-Cup® brand packs and accessories will 
guarantee the proper functioning and lifetime of your Keurig® Brewer. Any 
damage to or malfunction of your Brewer resulting from the use of non  Keurig Brewed
® K-Cup® brand packs and accessories may not be covered by 
this warrant y or may result in a ser vice fee if the damage or malfunction is 
determined to be caused by such use.
What is not covered by the Limited Warranty?
THIS WARR ANT Y DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL  DAMAGES SUCH A S PROPERT Y DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND E XPENSES RESULTING FROM ANY BRE ACH   
OF THIS WARR ANT Y, E VEN IF FORESEE ABLE. Some states or provinces 
do not allow the exclusion or limitations of incidental or consequential 
damages, so the above limitation or exclusion may not apply to you   
depending on the state or province of purchase.  Nor does this warrant y cover damages caused by use of non Keurig Brewed
® 
K-Cup® brand packs or accessories, ser vices performed by anyone other 
than Keurig or its authorized ser vice providers, use of parts other than 
genuine Keurig parts, or external causes such as abuse, misuse,  inappropriate power supply or acts of God.
Other Limitations
THIS WARR ANT Y IS E XCLUSIVE AND IS IN LIEU OF ANY OTHER E XPRESS  WARR ANT Y, WHE THER WRIT TEN OR OR AL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCL AIMS ALL OTHER WARR ANTIES WITH RESPECT TO 
YOUR B70 BRE WER, INCLUDING ANY IMPLIED WARR ANT Y OF  MERCHANTABILIT Y OR FITNESS FOR ANY PARTICUL AR PURPOSE. Some 
states or provinces do not allow disclaimers of such implied warranties or  limitations on how long an implied warrant y lasts, so the above limitation 
may not apply to you depending on the state or the province of purchase. 
How do you obtain warranty ser vice?
Keurig® Brewers are high-quality appliances and, with proper care, are   
intended to provide years of satisf ying per formance. However, should the 
need arise for warranty ser vicing, simply call Keurig Customer Ser vice at 
our toll free phone number 1.866.901.BRE W (2739). Please do not return your  Brewer for ser vicing without first speaking to Keurig Customer Ser vice to 
obtain an Authorization to Return number (ATR). Keurig
® Brewers returned   
without an ATR number will be returned to the sender without ser vicing.
Keurig, Incorporated  
55 Walkers Brook Drive  
Reading, MA 01867  
1. 8 6 6.9 01.BRE W (2 7 3 9)
17
SECTION 4  Troubleshooting
16
SITUATION  
Brewer does not  have power
Brewer will   
not brew
LCD Control Center  indicates “PRIME” 
and the blue light in 
the Water Reservoir  is flashingSOLUTION  
• Plug Brewer into an independent outlet.• Check to be sure that it is plugged in securely. • Plug into a different outlet. • Reset your home’s circuit breaker, if necessar y.• Make sure that the Power Switch has been turned  
on and LCD lights are illuminated.
•  After placing the K-Cup® pack in the K-Cup® Pack 
Holder, make sure the Handle is pushed down securely 
and the LCD Control Center indicates “RE ADY TO  BRE W” with the Left, Right and BRE W Butt ons flashing, 
then press the Left, Right or BRE W Button.
•  If the LCD Control Center indicates “ADD WATER,”   
add water to the Water Reser voir or make sure the  Water Reser voir is seated properly in its base.
•  If the LCD Control Center indicates “ADD WATER” 
even after refilling, contact Customer Ser vice at 
1. 8 6 6.9 01.BRE W (2 7 3 9).
• The Exit Needle may be clogged (refer to page 14).• If the LCD Control Center indicates “PRIME” and the  blue light in the Water Reser voir is flashing, see below.
• C ompletely remove the Water Reser voir and 
thoroughly clean (refer to page 14). Ensure the   
Water Reser voir  is fully filled with water. Return it   
to the Brewer and ensure it is seated properly   
(refer to page 6).
•  If you have completed the above procedure t wo 
times and this situation persists, contact Customer 
Ser vice at 1.866.901.BRE W (2739).  
 
SITUATION  
Brewing a   
partial cup
The time is not   
displayed on the  LCD Control  
 Center
Brewer shuts   
off or turns on   
automatically
The blue light in 
Water Reservoir is  flashingSOLUTION  
• The Exit Needle may be clogged (refer to page 14).• Clean the K-Cup® Pack Holder A ssembly if necessar y 
and rinse under faucet (refer to page 13).
•  The Water Reser voir may have been removed during 
brewing. Replace the Water Reser voir and per form a 
cleansing brew without a K-Cup
® pack.•  De-scale the Brewer (refer to page 14).• If you have repeated the de-scale procedure on your 
Brewer t wo times and it is still only brewing   
a partial cup, contact Customer Ser vice at   
1. 8 6 6.9 01.BRE W (2 7 3 9).
•  The time will not be displayed on the LCD Control 
Center unless you have set it. To set the clock, follow the procedure on page 10.
•  If power is interrupted to the Brewer, you will need 
to set the clock again using the procedure on page 10.
•  Check to make sure that the Auto Off timer   
and/or On/Off time features have not been set.   
To do this, press the MENU Button and scroll  through the programming options. “OFF” should   
be indicated for Auto Off timer and On/Off. If “OFF”   
is not indicated, follow directions on page 10 to reset.
•  The water level is low and a full cup cannot be 
brewed. Add water to Water Reser voir.
•  If the LCD Control Center indicates “PRIME,” please 
see situation to the left (LCD Control Center  indicates “PRIME” and the blue light in the Water 
Reser voir is flashing).
If any problems persist, contact Customer Ser vice at 1.866.901.BRE W (2739)