Keurig 20 K250 User Guide

							Owner’s manual
Special Edition/Signature B6\f Keurig® Brewer
DTP1005-001900   CTP09  
						

							3
TABLE OF CONTENTS
KEURIG® GOURME T SINGLE CUP HOME BRE WING SYSTEM
Special Edition/Signature B60 —  Using Your Brewer
S E T- U P 
Helpful Hints  ........................................................................\
................
4 
Unpacking  ........................................................................\
....................
4 
Features  ........................................................................\
.......................
5
SECTION 1 — SET-UP & FIRST BRE W  
Set-Up & First Brew ........................................................................\
...6
SECTION 2 — CONTROLS & INDICATORS  
Setting the Clock ........................................................................\
.......10 
Programming On/Off Features  ......................................................10 
Programming Brew Temperature  .................................................12
SECTION 3 — CLEANING & MAINTENANCE 
Cleaning ........................................................................\
......................12 
De-Scaling ........................................................................\
..................
13 
Storage  ........................................................................\
.......................
14
SECTION 4 — TROUBLESHOOTING ..................................................15
SECTION 5   — WARRANTY ................................................................16
Record your Brewer Serial Number here.See Unpacking Instr uctions on page 4 for serial number location.
Removing the serial number label from the Brewer will void warr ant y. 
CAUTION: There are two sharp needles that puncture the K-Cup® pack, one 
above the K-Cup® Pack Holder and the other in the bottom of the K-Cup® Pack 
Holder. To avoid risk of injur y, do not put your fingers in the K-Cup® Pack 
Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup
® Pack Holder during the   
brew  process. To avoid risk of injur y, do not lift the Handle or open the K-Cup®  
Pack  A ssembly Housing during the brewing process.
CAUTION:  Please always keep the Brewer in its upright position to avoid 
potential injury and/or damage to your Brewer.
SHORT CORD INSTRUCTIONS:
 A shor t power supply cord is provided to 
reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set or 
extension cord should be at least as great as the electrical rating of the 
appliance; (2) the cord should be arranged so that it will not drape over the 
counter top or tabletop where it can be pulled on by children or tripped over 
unintentionally; and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING 
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, 
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WARNING
WARNING:  TO REDUCE THE RISK OF FIRE OR 
ELECTRIC SHOCK, DO NOT REMOVE THE 
BOTTOM COVER. NO USER SERVICEABLE 
PARTS ARE INSIDE. REPAIR SHOULD BE DONE 
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR  
ELECTRIC SHOCK   DO NOT OPEN
!
2
IMPORTANT SAFEGUARDS  Safe Operation & Use
When using electrical appliances, basic 
safety precautions should be followed, 
including the following:
 1. Read all instructions before using.
 2.  Do not touch hot sur faces. Use handles   
and knobs when available.
 3. This appliance must be properly 
installed and located in accordance 
with these instructions before it is used.
 4. The use of accessor y attachments 
not recommended by the appliance 
manufacturer may result in fire, 
electrical shock or injur y to persons.
 5. Do not place on or near a hot gas or 
electric burner, or in a heated oven.
 6. Do not use outdoors.
 7. To protect against fire, electric shock 
and injur y do not immerse cords, plugs, 
or the appliance in water or any other 
liquid.
 8. Do not over fill the Water Reser voir   
with water.
 9. Use  only water  in this appliance! Do 
not put any other liquids or foods in the 
Water Reser voir except as instructed in 
the Cleaning Instructions in this guide.
 10.  Turn off and unplug the Brewer before   
cleaning or maintenance. Allow to cool   
before putting on or taking off par ts   
and before cleaning the appliance.
 11. For best operation, plug the appliance   
into its own electrical outlet on a 
dedicated circuit to prevent flickering 
of lights, blowing of fuses or tripping a 
circuit breaker.
 12 . Do not operate any appliance with a   
damaged cord or plug or after 
the appliance malfunctions or is 
damaged in any manner. Contact 
Keurig Customer Ser vice to repor t 
any malfunction of or damage to the 
B r e w e r.
 13. Do not let the cord hang over the edge 
of the table or counter, or touch hot 
surfaces.
 14 .  To disconnect, press the Power Button 
on the Brewer to ‘OFF’ status and then 
remove the plug from the wall outlet.
 15. Close super vision is necessar y when 
any appliance is used by or near 
children.
 16. Do not lift the Brewer Handle while   
brewing is in progress.
 17. Always keep the Water Reser voir Lid   
on the Water Reser voir unless you are   
refilling it.
 18. This appliance is equipped with a power 
cord having a grounding wire with a   
grounding plug. The appliance must 
be grounded using a 3-hole properly 
grounded outlet. In the event of an  electrical shor t circuit, grounding 
reduces the risk of electrical shock.
 19. If the outlet is a standard 2-prong wall 
 
outlet, it is your personal responsibility   
and obligation to have it replaced with a 
properly grounded 3-prong wall outlet.
 20. Do not, under any circumstances, cut or 
remove the third (ground) prong from 
the power cord or use an adapter.
 21.  Consult a qualified electrician if 
the grounding instructions are not 
completely understood, or if doubt 
exists as to whether the appliance is 
properly grounded.
 22. Do not use the appliance for other than 
its intended use.
S av E T HE SE  
I NSTRUCTIONS.
W aRNING TO USERS a ND PaRENTS
1. DO NOT permit children to use Brewer   
unless there is adult super vision. Brewer   
dispenses ver y hot water.
2. SPECI aL NOTICE FOR HOT COCO a USERS:  
IMMEDI aTELY a FTER USING a HOT COCO a  
K-CUP
® P a CK, RUN a Hot Water Brew Cycle  
without a K-Cup® pack to avoid the possibility   
of clogging the exit needle. DO NOT assume   
the next user will do this.    
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							Set-Up
5
11 :
5 6AM
READY
TO BREW
MENU
Features  Special Edition/Signature — Model B60 Brewer
a
B
M
C
IN
LK
J
H
E
F
GDT
R
S
0PQ
  A.  Water Reser voir Lid B. Water Reser voir C. Water Reser voir   
Lock Tab Slots
 D.  Handle E. Funnel
 F.  K-Cup® Pack Holder   
(E and F are the K-Cup® 
Pack Holder Assembly) 
 G.  Lid H. K-Cup® Pack   
Assembly Housing
 I.  Housing
 J. Drip Tray Plate K. D r i p  Tr a y L. Drip Tray Base M. Vent N. Power Cord
 O. Small Cup Button 5.25 oz. P. Small Mug Button 7.25 oz. Q. Large Mug Button 9.25 oz.
R. Menu ButtonS. LCD Control CenterT. Power Button
Special Edition/Signature B60 Brewer Controls and Indicators
4
Helpful Hints 
 1.   Plug Brewer into its own grounded outlet.  If the electric circuit is overloaded with other   
appliances, your Brewer may not function   
properly. The Brewer should be operated on   
its own circuit, separate from other appliances.
  2.  Keep your Brewer turned “ON.”   To brew a fresh cup of coffee, tea or hot cocoa  
any time you want, keep your Brewer turned 
“ON” all the time. However, the Brewer is fully  programmable so you can set it to turn on and off automatically to match your schedule.   
Or, if you prefer, set the Brewer to automatica lly 
turn off after a period of time. Follow the simple  instructions on pages 10–12 to find the settings 
that are most convenient for you.
  3.   For the best tasting gourmet coffee, tea or  
hot cocoa, Keurig recommends using bottled  
or filtered water. 
 
Water quality varies from place to place.   
If you notice an undesirable taste in your cup   
of coffee, such as chlorine or other mineral 
tastes, we recommend you consider using  bottled water or water from a filtration 
system. For best results, carefully follow  manufacturer’s instructions when using any 
water filtration system.  
 4.  Customize the size, flavor & brew that’s   
perfect for you.  
With the choice of over 200 varieties of   
K-Cup® packs and 3 brew sizes (Small Cup-  
5.25 oz., Small Mug-7.25 oz. and Large  Mug-9.25 oz.), your Keurig
® Brewer gives you 
endless options to customize the size, flavor 
and brew that’s per fect for you. For a strong, 
intense cup, select an Extra Bold K-Cup
® 
pack (with up to 30% more ground coffee than 
regular varieties) and brew size that’s right 
for you. The smaller the brew size, the more  intense flavor in your cup. The larger the brew 
size, the less intense flavor in your cup.
  5.  Remove K-Cup® pack after use.  Please see page 7 for brewing instructions.  
 6.  Brewing into a travel mug.  To brew into a travel mug, simply remove the  
Drip Tray A ssembly and place the travel mug  
on the Drip Tray Base.
  7.  De-scale Brewer regularly.   Please see pages 13 and 14 for instructions.
Unpacking Instructions
 1. Place Brewer box on a large steady sur face  
(such as a table or counter top) or on the floor.  Open the box.
   2.
 
Remove enclosed literature.
  3. Turn the box on its side with front of box   
face down.
 4. Reach into the box and grasp the plastic bag   
that contains the Brewer.
 5. Carefully pull the plastic bag (and packaging 
materials) toward you and out of the box. The 
Brewer will still be encased in the poly foam   
and be on its side.
 6. Remove the top poly foam packaging material.
 7.  Carefully lift Brewer off of the bottom poly foam 
and place it upright on a flat, steady sur face.
  8. Lift plastic bag off of Brewer.
 9.  Record the serial number for this Brewer on 
page 3 of this guide. The serial number can 
be found on the bottom of the Brewer box or  on the Brewer behind the Drip Tray (when 
removed).
 10.  Place the Brewer upright on a flat, steady 
surface. Remove tape holding Water Reser voir  in place. 
We recommend you save all packing materials in  case future shipping of the product is necessar y.
WARNING:   
Keep all plastic bags away  
from children.  
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							67
SECTION 1  Set-Up & First Brew
Ready to Brew Your First Cup
 1. LCD Control Center will indicate   
“READY TO BREW.” 
 2. Place a cup or mug on the Drip Tray Plate.
  3. Lift the Handle and the K-Cup® Pack Holder   
will open toward you (fig. 6).
 4. Select a K-Cup® pack.  
NOTE:  Do not remove the foil   
lid or puncture the K-Cup® pack.
 5. 
Place a K-Cup® pack in the   
K-Cup® Pack Holder (fig. 7).  
CAUTION: There are two sharp needles that  
puncture the K-Cup® pack, one above the 
K-Cup® Pack Holder and the other in the bottom 
of the K-Cup® Pack Holder. To avoid risk of 
injur y, do not put your fingers in the K-Cup® 
Pack Assembly Housing.
 6. 
Lower the Handle to close the Lid over the  
K-Cup® Pack Holder. (When it is closed 
completely, the LCD Control Center will 
indicate “RE ADY TO BRE W” and the Small 
Cup, Small Mug and Large Mug Buttons will 
flash for up to 60 seconds.) 
NOT READY
Setting Up Your Brewer
 1.  Unwrap cord and plug the Brewer into   
a grounded outlet. Remove all pieces of   
packing tape and clear plastic sticker   
from LCD Control Center.
 2.  Place a large mug (10 oz. minimum) on the   
Drip Tray Plate.
  3. Remove the Water Reser voir from Brewer   
by first removing Lid from Reser voir (fig. 1), 
then lifting Reser voir straight up and away   
from Brewer (may be tight), (fig. 2). Rinse   
with fresh water.
IMPORT aNT: You cannot use your Keurig® Brewer until 
it has been set-up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures
below freezing, allow Brewer at least two hours to 
reach room temperature before brewing. A frozen   
or extremely cold Brewer will not operate.
 4.  Fill Water Reser voir with bottled or filtered 
water so that the water level is just below the 
top edge of the Water Reser voir.
 5. Place Water Reser voir base into the left side 
of the Brewer and be sure the Water Reser voir 
Lock Tabs engage with the Brewer. Replace 
Lid on Water Reser voir.
 6. Press the Power Button found directly  
above the LCD Control Center (fig. 3).
 7.  The LCD Control Center will illuminate and  
indicate “NOT RE ADY.” 
NOTE: A K-Cup® pack 
should not be used for this sequence
.
  
NOTE: If the Water Reser voir is empty or   
not in place on the Brewer, the LCD Control   
Center will also indicate “ADD WATER .” None   
of the buttons will be activated until water 
is added to the Water Reser voir and Water 
Reser voir is in place.
Small  Mug 
READY
TO BREW
MENU
fig. 2
Power
     ADD 
WATER
NOT READY
fig. 3
fig. 4
fig. 5
fig. 6
fig. 7
fig. 1
L o c k Ta b s
 
8. The Brewer will automatically fill the   
internal tank with water and then the water  will be heated. This will take about 4 minutes.   
During the heating period, “NOT RE ADY”   
(fig. 4) is indicated on the LCD Control   
Center. 
Do not lift Handle during this   
heating period. 
    Once the water is heated, “RE ADY TO BRE W”   
will be indicated and the Brew Buttons will be   
illuminated (fig. 5). 
NOTE: You may see small 
amounts of water coming from the Vent and   
dripping into the Water Reservoir during this   
and subsequent heating  — this is normal.
 9.
  Lift and lower the Handle. Press the Small 
Mug Button to star t a cleansing brew. Pour the hot water into the sink.
 10.  The one-time set-up process is now   
complete and you are ready to brew!  
NOTE: The Brewer may take 15 seconds   
between brews and then “RE ADY TO BRE W”   
will be indicated.                           
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							89
 7. Choose the cup size of coffee, tea or hot   
cocoa by pressing the button that indicates  your choice. The Small Cup choice will yield 
a 5.25 oz. ser ving, the Small Mug choice will  yield a 7.25 oz. ser ving and the Large Mug 
choice will yield a 9.25 oz. ser ving. 
NOTE: If   
you do not push a Brew Button in 60 seconds,  the LCD Control Center will return to “RE ADY 
TO BRE W” and the Brew Buttons will be  disabled to prevent accidental activation.  Re-activate the Brew Buttons by raising and lowering the Handle completely.
  8.
 The LCD Control Center will indicate 
“BRE WING” and the cup size you selected   
will illuminate. 
CAUTION: There is extremely 
hot water in the K-Cup® Pack Holder during the 
brew process. To avoid risk of injur y, do not lift 
the Handle or open the K-Cup
® Pack Assembly 
Housing during the brew process.
 9.
  There may be a shor t pause prior to coffee   
being dispensed. The entire brew process  lasts for approximately 1 minute and ends   
with a burst of air to remove all liquid from   
the K-Cup
® pack.
Ready to Brew Your First Cup (Continued)  10.  Lift the Handle, remove and dispose of the   
used K-Cup® pack. CAUTION: K-Cup® pack   
will be hot.
 11.
  Enjoy your first cup of Keurig Brewed®  
gourmet coffee, tea or hot cocoa!
 12 .  Your Brewer may indicate “NOT RE ADY” as it 
heats water for the next brew cycle. The   
“RE ADY TO BRE W” indication will return to   
the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will  
fill in preparation for the next brew. The pump  
will make a vibrating sound. This is normal.
Stopping the Brew Process
If you need to stop brewing after the process has star ted, press the Power 
Button to turn the Brewer off. The flow of coffee, tea or hot cocoa will stop,  the heating element will shut off, and the blue lights illuminating the brew 
buttons and Water Reser voir will disappear. 
NOTE:  You may get less coffee, tea 
or hot cocoa in your cup during your next brew. We recommend that you per form  a cleansing brew after a terminated brew. Then your NE X T brew will be the  volume you have selected.
SECTION 1 Set-Up & First Brew
adding Water
The LCD Control Center will indicate “ADD 
WATER” when the water level in the Water   
Reser voir is low or if the Water Reser voir has  been removed (fig. 8). The blue light in the Water 
Reser voir will also blink when water needs to be 
added. The Brewer will not allow you to brew when   
“ADD WATER” is indicated.
The Water Reser voir can be filled in two ways. 
 1.  
Lift off the Water Reser voir Lid and pour water  
directly into the Water Reser voir while it is still  attached to the Brewer, then replace the Lid.
 2.  Remove the Water Reser voir from Brewer by first removing Lid from   
the Water Reser voir, then lifting the Water Reser voir straight up and   
away from Brewer. Fill with water. Place the Water Reser voir back on   
the Brewer and replace the Lid.
  IMPORTANT : Do not remove the   
Water Reser voir during the brewing process.
Brewing Iced Beverages
Your iced tea and iced coffee taste best when fresh-brewed hot over ice. Tr y it by  placing a tall cup filled with ice on the Drip Tray Plate (the Dr ip Tr ay A ssembly 
can be removed to accommodate taller cups), choose your favorite K-Cup
® 
pack and press your preferred cup size. Also, look for the Brew Over Ice™ icon 
on K-Cup® packs that are specially crafted to brew over ice! IMPORTANT:  Do not 
brew into a cup made of glass. Doing so may cause the glass to crack or break.
Brewing Hot Water
Your Brewer is able to produce hot water for making hot cocoa from a packet,   
for use in cooking, for making soups, etc. Simply follow the instructions on   
page 7 — “Ready To Brew Your First Cup” without adding a K-Cup
® pack.  
NOTE: After brewing a hot cocoa K-Cup® pack, we recommend running a 
cleansing brew without a K-Cup® pack.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge  the water from the inner tank.
 1.  If there is water in the Water Reser voir, remove the Lid, then lift the   
Water Reser voir straight up and away from Brewer. Discard water, rinse 
and refill with water. Place the Water Reser voir back on the Brewer and  replace the Lid. (If there is no water in the Water Reser voir, simply refill.)
 2.  Be sure the Brewer is turned on. Raise and lower the Handle on the 
Brewer without inser ting a K-Cup® pack.
  3. The LCD Control Center will indicate “RE ADY TO BRE W” and the Small 
Cup, Small Mug and Large Mug Buttons will flash. Be sure to have a large mug on the Drip Tray Plate and then press the Large Mug Button.
 4.  Repeat steps 2 and 3 one more time to completely purge water from   
inner tank.
If you are experiencing any problems with your Brewer, please contact   
Customer Ser vice at 1.866.901.BRE W (2739).
 
   
  ADD 
WATER
NOT READY
fig
. 8
Small Cup
(5.25 oz.) 
Small Mug
(7.25 oz.) 
Large Mug
(9.25 oz.)      
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							1110
SECTION 2  Controls & Indicators (LCD Control Center)
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in  
the LCD Control Center. 
NOTE:  You must set the clock if you will be using the 
On/Off Time programming feature.
 1. 
Press the Menu Button.
 2. The word “OFF” will appear at the bottom   
of the LCD Control Center to indicate that   
the clock is not set. The programming 
options will appear on the LCD Control  Center with a small arrow pointing to “SE T 
CLOCK” (fig. 9). “H” (Hour) and “M” (Minute) will appear and blink.
  3. Press or hold the blue Small Cup Button under 
the blinking “H” until you have reached the 
appropriate hour. If the hour has passed 12,  the indicator switches from “AM” to “PM.”
 4.  Press or hold the blue Large Mug Button under 
the blinking “M” to set the minutes.
 5.  When you have reached the correct time, press the Menu Button five 
times to scroll through the remaining programming options and exit   
the programming mode.
 6.  The correct time should now be displayed in the LCD Control Center.  
NOTE: If power is interrupted to the Brewer by unplugging it, or if power   
is lost, follow the procedure above to reset the time as the clock will not be 
visible until the time is set. 
Menu
SET CLOCK
  AUTO OFF
  ON OFF TIME
  BREW TEMP
SetHoursSetMinutes
MENU
fig . 9
 c.  After setting the desired Auto Off time, press   
the Menu Button four times to scroll through   
the remaining programming options and exit   
the programming mode. “AUTO OFF SE T”   
(fig. 11) will now be indicated to confirm that   
it has been set. 
  d.  To cancel the Auto Off feature, press the   
Menu Button t wice to reach the Auto Off 
programming mode. Press and release the  Small Cup Button under the blinking “H”   
to advance one hour at a time until “OFF”   
is indicated.
  3.  Program your Brewer for a specific On/Off Time. NOTE : To use this 
programming feature, the clock must be set to the correct time. The clock  will not be displayed unless the time is set.
  a.  After setting the correct time (required), press 
the Menu Button three times to program the On 
Time feature. The LCD Control Center will show  the programming options with a small arrow 
next to “SE T ON TIME” (fig. 12). 
  b.  Press or hold the blue Small Cup Button under 
the “H” to scroll through the hours to your 
desired “ON TIME” hour.
  c.  Press or hold the blue Large Mug Button under 
the “M” to scroll through the minutes to your 
desired “ON TIME” minutes.
  d.  After setting the desired time, press the Menu Button to save the   
“ON TIME” and move to the “SE T OFF TIME” (fig. 13). 
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea  or hot cocoa on your own schedule. By programming your Brewer to turn on 
each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee.
  1.  Leave it ON all the time. The Brewer can be left on all the time so that it is 
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To turn  the Brewer off at any time, simply press the Power Button. 
( NOTE :
 Although 
the clock remains on if set, you can not brew a cup of coffee, tea or hot cocoa.) 
Press the Power Button again to restore power to the Brewer. You will have 
to wait for the water to heat up before the Brewer is ready to brew.
 2.  Set the Brewer to Auto Off following a   
specified period of time after the last brew. 
  a.  Press the Menu Button t wice to program the 
Auto Off feature. The LCD Control Center will 
display the programming options with a small  arrow next to “SE T AUTO OFF” (fig. 10).
  b.  Press or hold the blue Small Cup Button   
under the blinking “H” to advance 1 hour at   
a time, up to 9 hours.   
e.  If you want to set an “OFF TIME,” repeat the 
procedure above in steps b & c to set your 
desired “OFF TIME.” 
  f.  To complete the process, press the Menu Button 
t wo more times to exit the programming mode. 
The LCD Control Center will indicate the options  you have set.
  g.  The On Time and Off Time functions oper ate 
independently from one another. To cancel 
either set function, follow the steps above and  use the “H” and “M” buttons to advance to 12:00 
AM. Make sure the M button is set to :00, then 
change the “H” button. When you reach 12:00  AM, the Control Center will indicate “OFF” and  the function will be disabled.
EXAMPLE : If you chose to set the On Time at 
 
6:15 AM and the Off Time for 10:00 PM, then the  Brewer will be “RE ADY TO BRE W” and maintain hot water in the tank during that time so that it is 
always ready for you to brew. If you wanted to  brew outside this window, simply press the Power 
Button and you can brew as soon as the water is  heated and the “RE ADY TO BRE W” is indicated on the LCD Control Center. 
NOTE :
 The “AUTO OFF” Timer and the On/Off Time programming options 
operate independently but can also be programmed to work together. For example,  you can set the On Time function to turn on at 7:00 AM and then set the Auto Off  
Timer function to turn off the Brewer two hours after the last brew (fig. 14).
Menu x2
        CLOCK
SET AUTO OFF
   ON OFF TIME
   BREW TEMP
MENU
fig. 10
11 :
5 6AM
READY
TO BREW
MENU
AUTO OFF SET
 CLOCK
  AUTO OFF
SET ON        TIME
  BREW TEMP
MENU1 1 :
5 6AM
PM
fig . 12
 CLOCK
  AUTO OFF
SET     OFF TIME
  BREW TEMP
MENUAM
PM
fig . 13
11 :
5 6AM
READY
TO BREW
MENU
AUTO OFF SET
ON   TIME SET
fig . 14
fig . 11         
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							13
Programming Brew Temperature (187° – 192º F)
The Brewer brews at a preset temperature of 192°. You can adjust this 
temperature down by 5 degrees if you prefer a cooler cup of coffee, tea   
or hot cocoa. Simply follow the instructions below.
 1.  Press the Menu Button on the LCD Control Center five times to   
program the Brew Temperature feature.
 2.  The LCD Control Center will now display the programming options with   
a small arrow next to “SE T BRE W  TEMP” (fig. 15). Also, the temperature 
192° (initial setting) will be indicated at the bottom of the LCD Control  Center to indicate the current temperature setting.
  3    . A minus sign will appear over the Small Cup Button and/or a plus sign   
over the Large Mug Button. Use these buttons to raise or lower the  temperature one degree at a time.
 4.  Once you have reached your desired brew 
temperature, press the Menu Button once   
to exit the programming mode. “BRE W TEMP 
SE T” will be indicated in the LCD Control   
Center if you have changed it from 192°.
 5.  To change the brew temperature again, repeat 
steps 1 through 3 to change the temperature   
up or down, remembering that the temperature 
can only be bet ween 187° and 192° .
Cleaning External Parts
Regular cleaning of the Brewer’s external components is recommended.
 1.  Never immerse the Brewer in water or other liquids. The Housing and 
other external components may be cleaned with a soapy, damp,   
non-abrasive cloth.
 2.  The Drip Tray can accumulate up to 8 oz. of over flow. The Drip Tray   
and Drip Tray Plate should be periodically inspected and rinsed clean.   
To remove the Drip Tray A ssembly, simply slide it toward you, keeping  it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate 
should not be placed in the dishwasher. They should be cleaned with a 
damp, soapy, non-abrasive cloth and rinsed thoroughly .
Cleaning the K-Cup® Pack Holder assembly
 1.  Cleaning the Par ts  —The K-Cup® Pack Holder  
A ssembly can be placed onto the top shelf of a 
dishwasher. 
NOTE:  Use low temperature cycles 
in the dishwasher. 
To remove from the Brewer, 
open the cover by lifting the Handle. Grasp the  top of the K-Cup
® Pack Holder with one hand 
while pushing up on the bottom of the K-Cup® 
Pack Holder from underneath with the other 
until it releases (fig. 16). After cleaning, align the  K-Cup
® Pack Holder with the opening using the 
t wo front ribs as a guide, and snap into place 
from the top. 
  2.  Cleaning the Funnel  —The Funnel can be 
removed from the K-Cup® Pack Holder by 
pulling on it until it snaps off (fig. 17). The Funnel  is dishwasher safe. To replace it, just snap it   
back onto the K-Cup
® Pack Holder Assembly.
  3.  Cleaning the Exit Needle  —The Exit Needle is 
located on the inside bottom of the K-Cup® Pack 
Holder A ssembly. Should a clog arise due to 
coffee grinds, it can be cleaned using a paper 
clip or similar tool. Remove K-Cup
® Pack Holder 
Assembly and detach Funnel. Insert the paper 
clip (fig. 17) into the Exit Needle to loosen the 
clog and push it out. The K-Cup
® Pack Holder is 
dishwasher safe. 
CAUTION : There are sharp
needles that puncture the K-Cup® pack above the K-Cup® Pack Holder and in 
the bottom of the K-Cup® Pack Holder. To avoid risk of injur y, do not put your 
fingers in the K-Cup® Pack Assembly Housing.
Cleaning the Water Reservoir & Water Reservoir Lid
The Water Reser voir Lid and Water Reser voir should be periodically 
inspected and cleaned.
The Water Reser voir Lid or Water Reser voir should not be put into the  dishwasher. They should be cleaned with a damp, soapy, non-abrasive   
cloth and rinsed thoroughly. Do not dr y the inside of the Water Reser voir   
with a cloth as lint may remain. 
To clean the filter screen at the base of your Water Reser voir, empt y   
the Water Reser voir and follow one or all of the following procedures.   
NOTE: If you are using a water filter inside the Water Reser voir, remove   
it before cleaning.
 1.  Rinse the filter screen with the strong force of water from your faucet. 
 2.  If you have a sprayer, aim the water spray at the filter screen. 
  3.  
Fill the Water Reser voir with approximately t wo inches of clean water   
and agitate (shake) the Water Reser voir.
Empt y the Water Reser voir then fill it with clean water and return it to the Brewer.  If needed, repeat above procedures. 
CAUTION:  Please rinse the Water Reser voir 
thoroughly after cleaning. This will ensure that no cleaners or cleaning solutions 
remain as they may contaminate the water supply in the Brewer.
De-Scaling Your Brewer
Mineral content in water varies from place to place. Depending on the   
mineral content of the water in your area, calcium deposits or scale may build 
up in your Brewer. Scale is non-toxic, but left unattended, it can hinder Brewer  performance. De-scaling your Brewer helps maintain the heating element and 
other internal par ts of the Brewer that come in contact with water. 
The Brewer should be de-scaled ever y 3-6 months to ensure optimal performance. It is possible for 
calcium deposits to build up faster, making it  necessar y to de-scale more often.
You should promptly de-scale if “DE-SCALE” is  indicated on the LCD Control Center (fig. 18). 
However, even if “DE-SCALE” is not indicated,   
you should continue to de-scale your Brewer 
ever y 3-6 months. Properly follow the de-scaling  procedure described on page 14. 
SECTION 3  Cleaning & MaintenanceSECTION 2 Controls & Indicators (LCD Control Center)
12
192°
 CLOCK
  AUTO OFF
  ON OFF  TIME
SET BREW TEMP
MENU
fig . 15fig . 16
SET 
MENU11 :
5 6AM  DE-SCALE
fig . 18
!
fig . 17       
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							1415
De-Scaling Instructions
A. PREPARE  Step 1:  To begin, you will need the following:  
At least 4 8 oz. of undiluted white vinegar   
Access to an empt y sink  
A large ceramic mug (do not use a paper cup) 
Step 2:  Empt y the water from the Water Reser voir.
Step 3:  Disable Auto Off features. 
B. FILL AND CLE AN   Step 1: Pour approximately 4 8 oz. of the vinegar into the Water Reser voir.
Step 2:   Place a large mug on the Drip Tray Plate and run a cleansing brew.  
DO NOT USE A K-CUP® PACK , just press a Brew Button.  
Pour the contents of the large mug into the sink.
Step 3:   Repeat the brew process without a K-Cup
® pack until “ADD WATER”   
is indicated.
Step 4:  Now let the Brewer stand for at least 4 hours while still on.
Step 5:   Discard any residual vinegar and rinse the Water Reser voir thoroughly.
C. RINSE   Step 1: Ensure the Water Reser voir is filled with fresh water.
Step 2:   Place a large mug on the Drip Tray Plate and run a cleansing brew. 
Pour the contents of the large mug into the sink.
Step 3:  Repeat brew process until “ADD WATER” is indicated. 
Step 4:   You may need to per form additional cleansing brews if you notice any 
residual taste.
NOTE : If “DE-SCALE” is still indicated after completing the procedure,   
repeat the de-scaling procedure above.
Service
Beyond these recommended cleaning and maintenance procedures, this 
Brewer is not user ser viceable. For ser vice, please refer to the Warranty 
section of this guide. 
Storage 
Empt y the Water Reser voir before storing, and take care to ensure that you 
store your Brewer in a safe and frost free environment. Please be sure to 
store your Brewer in its upright position to avoid water leakage from the inner 
tank. If you store the Brewer in a cold environment, you run the risk of water 
freezing inside the Brewer and causing damage. When you prepare to use it 
after storage, we recommend rinsing the Water Reser voir with fresh water 
and running three cleansing brews without a K-Cup
® pack.
If you plan to move your Brewer to a different location, turn the Brewer   
off, unplug it, and empt y the Water Reser voir. If your Brewer has been in   
an environment below freezing, please be sure to let it warm to room   
temperature for at least 2 hours before using.
SECTION 4  Troubleshooting
SITUa TION 
Brewer does not 
have power
Brewer will   
not brew  
 
 
 
 
 
 
 
 
 
 
 
 
LCD Control Center  indicates “PRIME” 
and the blue light in 
the Water Reservoir  is flashing
SOLUTION 
• Plug Brewer into an independent outlet.  • Check to be sure that it is plugged in securely.   • Plug into a different outlet.   • Reset your home’s circuit breaker, if necessar y.•   Make sure that the Power Button has   
been turned on.
•    After placing the K-Cup® pack in the K-Cup® Pack Holder, 
make sure the Handle is pushed down securely and the  LCD Control Center indicates “RE ADY TO BRE W” with the   three Brew Buttons blinking, then press the Small Cup, 
Small Mug or Large Mug Button.
•    If the LCD Control Center indicates “ADD WATER,” add 
water to the Water Reser voir or make sure the Water 
Reser voir is seated properly in its base.
•    If the LCD Control Center indicates “ADD WATER” 
even after refilling, contact Customer Ser vice at 
1. 8 6 6.9 01.BRE W (2 7 3 9).
•  The Exit Needle may be clogged (refer to page 13).
•   If the LCD Control Center indicates “PRIME” and the 
blue light in the Water Reser voir is flashing, see below.
•   C ompletely remove the Water Reser voir and 
thoroughly clean (refer to page 13). Ensure the   
Water Reser voir  is fully filled with water. Return it to 
the Brewer and ensure it is seated properly.
•    If you have completed the above procedure t wo times 
and this situation persists, contact Customer Ser vice 
at 1. 8 6 6.9 01.BRE W (2 7 3 9).  
SITUaTION 
Brewing a   
partial cup
The time is not   
displayed on the 
LCD Control Center
My Brewer shuts   
off or turns on   
automaticallySOLUTION 
•  The Exit Needle may be clogged (refer to page 13).•   Clean the K-Cup® Pack Holder if necessar y and rinse   
under faucet (refer to page 12).
•    The Water Reser voir may have been removed during 
brewing. Replace the Water Reser voir and per form a 
cleansing brew without a K-Cup
® pack.•    De-scale the Brewer (refer to page 13).•   If you have repeated the de-scale procedure on   
your Brewer t wo times and it is still only brewing   
a partial cup, contact Customer Ser vice at   
1. 8 6 6.9 01.BRE W (2 7 3 9).
•   The time will not be displayed on the LCD Control 
Center unless you have set it. To set the clock, follow the procedure on page 10. 
•    If power is interrupted to the Brewer, you will need to 
set the clock again using the procedure on page 10.
•   Check to make sure that the Auto Off Timer   
and/or On/Off Time features have not been set. To   
do this, press the Menu Button and scroll through  the programming options. “OFF” should be indicated 
for Auto Off Timer and On/Off. If “OFF” is not  indicated, follow directions on page 10 to reset.
SECTION 3 Cleaning & Maintenance (continued)
If any problems persist, contact Customer Ser vice at 1.866.901.BRE W (2739) 
DTP1005-001900   CTP09DTP1005-001900   CTP09  
						

							16
SECTION 5  Warranty
Limited One Year Warranty 
Keurig, Incorporated warrants that your Brewer will be free of defects in 
materials or workmanship under normal home use for one year from the date 
of purchase. It is recommended that you fill out and return the warrant y card 
enclosed with your Brewer so that your purchase information will be stored  in our system. Keurig will, at its option, repair or replace a defective Brewer without charge upon its receipt of proof of the date of purchase. If a 
replacement Brewer is necessar y to ser vice this warranty, the replacement  Brewer may be new or reconditioned. If a replacement Brewer is sent, a new  limited one year warranty will be applied to the replacement Brewer.
This warrant y only applies to Brewers operated in the United States and  Canada. This warrant y gives you specific legal rights, and you may also have 
other rights that var y from state to state and, in the case of Canada, from  province to province.
Only the use of Keurig Brewed
® K-Cup® brand packs and accessories will 
guarantee the proper functioning and lifetime of your Keurig® Brewer. Any 
damage to or malfunction of your Brewer resulting from the use of non  Keurig Brewed
® K-Cup® brand packs and accessories may not be covered by 
this warrant y or may result in a ser vice fee if the damage or malfunction is 
determined to be caused by such use.
What is not covered by the Limited Warranty?
THIS WARR ANT Y DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL  DAMAGES SUCH A S PROPERT Y DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND E XPENSES RESULTING FROM ANY BRE ACH   
OF THIS WARR ANT Y, E VEN IF FORESEE ABLE. Some states or provinces 
do not allow the exclusion or limitations of incidental or consequential 
damages, so the above limitation or exclusion may not apply to you   
depending on the state or province of purchase.  Nor does this warrant y cover damages caused by use of non Keurig Brewed
® 
K-Cup® brand packs or accessories, ser vices performed by anyone other 
than Keurig or its authorized ser vice providers, use of parts other than 
genuine Keurig parts, or external causes such as abuse, misuse,  inappropriate power supply or acts of God.
Other Limitations
THIS WARR ANT Y IS E XCLUSIVE AND IS IN LIEU OF ANY OTHER E XPRESS  WARR ANT Y, WHE THER WRIT TEN OR OR AL. IN ADDITION, KEURIG HEREBY SPECIFICALLY DISCL AIMS ALL OTHER WARR ANTIES WITH RESPECT TO 
YOUR B60 BRE WER, INCLUDING ANY IMPLIED WARR ANT Y OF  MERCHANTABILIT Y OR FITNESS FOR ANY PARTICUL AR PURPOSE. Some 
states or provinces do not allow disclaimers of such implied warranties or  limitations on how long an implied warrant y lasts, so the above limitation 
may not apply to you depending on the state or the province of purchase. 
How do you obtain warranty ser vice?
Keurig® Brewers are high-quality appliances and, with proper care, are   
intended to provide years of satisf ying per formance. However, should the 
need arise for warranty ser vicing, simply call Keurig Customer Ser vice at 
our toll free phone number 1.866.901.BRE W (2739). Please do not return your  Brewer for ser vicing without first speaking to Keurig Customer Ser vice to 
obtain an Authorization to Return number (ATR). Keurig
® Brewers returned   
without an ATR number will be returned to the sender without ser vicing.
Keurig, Incorporated  
55 Walkers Brook Drive  
Reading, MA 01867  
1. 8 6 6.9 01.BRE W (2 7 3 9) 
DTP1005-001900   CTP09DTP1005-001900   CTP09