Kamesan KS T2000_operating Manual

KS-T2000
Compact Audio Mixer
Operating Manual
3
+-20
VU
0
+4-30-20
-70Dy-M Dy-M+4-30 -20+4-70 -30Line A-
B
8 4
P
Line A-
B
8 4
P
Line A-
B
8 4
P
Dy-M
MONIR L R LRL
R + L
R L/R
L
-20
-70
05 -
-4005 -
-4005 -
-40 

Kamesan KS-T2000
3
Warnings and 
notices
Warnings and 
notices
Warnings and 
notices
Warnings and 
notices
Warnings and 
notices
Warnings and 
notices
Warnings and 
notices
Warnings and 
notices
Treat your Kamesan KS-T2000 in the same way that you would 
treat any piece of precision equipment. Although it is designed 
for rugged location use in a wide range of extreme conditions:
• Avoid spilling liquid over the unit or exposing it to extremely 
humid environments. 
 Do not subject the unit to extreme...

Kamesan KS-T2000
4
Warnings and notices  . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connection of microphones . . . . . . . . . . . . . . . . . . . . . .  3
After-sales service   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
Table of Contents  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General notes   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About this manual   . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5
Accessories, etc.  . . . . ....

Kamesan KS-T2000
5
General notes
General notes
General notes
General notes
General notes
General notes
General notes
General notesGeneral notes
Before\
Before operating the Kamesan KS-T2000, you should be aware 
of the following points:
 All XLR connectors (male and female) are wired with the fol-
lowing pinouts: 1=ground, 2=hot, 3=cold.
 The AC adaptor jack is a tip-negative connection. DO NOT 
attempt to make any connection to this jack except using an 
AC adaptor authorized by Kamesan.
 Always...

Kamesan KS-T2000
6
The Kamesan KS-T2000 is supplied with everything you need to 
start work.
However, you can purchase the following, in order to increase 
the capabilities and the functionality of the unit:
 Power adaptors: you can use the Kamesan PS-M12 mini 
power supply.
 Spare battery holders, allowing you to slip in a new power 
source at a moment’s notice.
The Kamesan KS-T2000 case is designed to hold and protect the 
unit against any wear and tear under the standard conditions of 
use for which...

Kamesan KS-T2000
7
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan 
KS-T2000
The Kamesan KS-T2000 controls and connections can be divid-
ed conveniently into three sections: the input section, the out-
put section, and the front panel.
The input side of the unit (on the left as you look at the front) is 
as follows):
Always make and break connections to and from the Kamesan KS-
T2000 with...

Kamesan KS-T2000
8
Connect balanced cables from microphones to the XLR inputs, 
and set the switches appropriately:
Always make sure that the input mode selected for each channel 
matches the device connected to the channel BEFORE turning on 
the power. Selecting the wrong type of device could result in dam-
age to equipment. If you have to change the input mode with the 
power connector, turn down both the input level faders and the 
monitoring level before changing the input mode.
For full details of...

Kamesan KS-T2000
9
Output section
Output section
Output section
Output section
Output section
Output section
Output section
Output section
The output section of the unit (on the right as you look at the 
front) is as follows:
For full details of the levels, impedances, etc. of these jacks, see 
the section on “Specifications” on page 19.
See below for details of connections.
Output section
MONI.IN
RL
OUTPUT
´
+~
+
-60+4-60+4DC INL
R
MAS.
OUT
Camera Mic
DC input jack Balanced XLR 
mic/line-level...

Kamesan KS-T2000
10
There are two sets of connections available from the Kamesan 
KS-T2000: the main balanced connectors and the unbalanced 
RCA connectors.:
You can use these different connectors for professional and 
semi-professional video equipmen
When you make the connections to the balanced connectors, 
note that there are two switch positions for the level of these out-
puts: +4 and –60. Make sure that you make the appropriate level 
setting for the device connected to the Kamesan KS-T2000.
Output...