JVC Tm H1700g Instructions

							ENGLISH
EXIT
CHROMA MENU
PHASE BRIGHTCONTRAST VOLUME/SELECT
                    4SHARPNESS :  00
ADJ. BAR POSI. :LOWERCOLOR TEMP. : 6500
COLOR SYSTEM : AUTO
RUSH DELAY : STD.
ASPECT RATIO : 4-3
Menu items Purpose  Setting range
SHARPNESS Picture sharpness
ADJ.BAR POSI Volume bar position
COLOR TEMP. Color temperature of white
balance
COLOR SYSTEM Color system
RUSH DELAY Delay value
ASPECT RATIO Aspect ratio
Front panel Function                     
Contentsbutton displayed
+Increase (to max. value)
4Forward the setting value
–Decrease (to min. value)
1Reverse the setting value
VOLUME/
SELECT (–)VOLUME/
SELECT (+)
Front panel Function                     
Contents
button displayed
CHROMA/
Forward selection mark (4)
PHASE
CONTRAST/
Reverse selection mark (4)
BRIGHT
Front panel Function                     
Contentsbutton displayed
MENU EXITQuit (or Release) the 
screen
1
2
3
4
HOW TO USE THE MENU FUNCTIONS
•SHARPNESS • COLOR SYSTEM
•ADJ. BAR POSI. • RUSH DELAY
•COLOR TEMP. • ASPECT RATIO You can set the following menu items.
Set them depending on your needs.
1. Press the MENU button.
The  screen is displayed.
*The on-screen display goes off automatically after about five
minutes with operation performed.
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select MENU items.
A selection mark (4) is put next to the selected item.
SHARPNESS
ADJ. BAR POSI.
COLOR TEMP.
COLOR  SYSTEM
RUSH DELAY
ASPECT RATIO
3. Press the VOLUME/SELECT buttons to set.
4. If you want to set the other menu items, repeat
procedures 2 and 3.
5. Press the MENU button to quit.
1 Selection mark (4): Indicates the
menu item you select.
2 Menu item: Menu items you can
select.
3 Setting display: Indicates the current
settings (value).
4 Function display: The functions of
the front panel buttons (5 buttons on
the left) correspond to the function
displayed.  screen

FunctionContentsdisplayed
Forward the menu item.
Reverse the menu item.
–Lower the adjustment
value. (to the minimum)
+Raise the adjustment
value. (to the maximum)
4Forward the setting value.
1Reverse the setting value.
EXIT Exits the  screen.
DISPLAY AND SELECTION IN THE 
SCREEN MODE (SETTING)
MENU
CHROMA
PHASE BRIGHTCONTRAST
VOLUME/SELECT
MENU
9
00     +01                                  +39     +40• • • • • • • • • • • •
LOWER       UPPER
6500       9300
AUTO       NTSC       AUTO       PAL
STD.       SLOW
*For normal use, leave the COLOR SYSTEM setting to AUTO.
If reception is unsatisfactory in AUTO position, set it to the appropriate color system mode (NTSC or PAL).
*When REMOTE SYSTEM is set to MAKE, and REMOTE ENABLE signal is short circuited (ON), “REMOTE”
is displayed on the ASPECT RATIO setting menu, and Aspect ratio cannot be operated from the front panel.
4-3       16-9
Notes:
●When the screen aspect ratio is set to
16 - 9 (16:9) in ASPECT RATIO, the
picture will be vertically reduced.
●RUSH DELAY sets the delay between
the time the power switch is pressed
and the time power is actually
supplied to the monitor’s circuits.
STD. : Power turns on
approximately 1 second after
the power switch is pressed.
SLOW : Power turns on
approximately 3 seconds
after the power switch is
pressed.
*When turning on multiple Color-
Video Monitors simultaneously, it is
recommended to use STD. or SLOW
settings to reduce the rush current
of the entire system.
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 11
 
						

							HOW TO USE THE MENU
FUNCTIONS 
(cont’d)
10
EXIT
CHROMA MENU
PHASE BRIGHTCONTRAST VOLUME/SELECT
DISPLAY AND SELECTIONS IN THE  MODE (SETTING)
•PICTURE SUB ADJ. • WHITE BALANCE • REMOTE SYSTEM
•H. POSITION • CONTROL  LOCK • INPUT  REMOTE
•V. POSITION • STATUS DISPLAY
You can set the following set-up menu items.
1. While pressing the MENU button, press the
CHROMA/PHASE button.
The  screen is displayed.
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select the desired menu item.
A selection mark (4) is put next to the selected item.
3. Press the VOLUME/SELECT buttons to set.
●For WHITE BALANCE items, select the CUT OFF or DRIVE
setting screen, then select the function display for adjustment.
●Press the EXIT (MENU) button to return to the  screen.
Notes:
 screen

1 Selection mark (4): Indicates the
menu item you select.
2 Menu item: Menu items you can
select.
3 Setting display: Indicates the
current settings (value).
4 Function display: The functions of
the front panel buttons (5 buttons
on the left) correspond to the
function displayed.
FunctionContentsdisplayed
Forward the menu item.
Reverse the menu item.
–Lower the adjustment
value. (to the minimum)
+Raise the adjustment
value. (to the maximum)
4Forward the setting value.
1Reverse the setting value.
EXITExit the 
screen.
DRVSelects DRIVE adjustment.
CUTOSelects CUT OFF
adjustment.
RBAdjusts red and blue
signal level.
RGBAdjusts red, green and
blue signal level.
Turns the ON-SCREEN
display on or off. (This
DISP function is effective only
in the DRIVE or CUT OFF
adjustment mode.)
Front panel Function                     
Contentsbutton displayed
CHROMA/
Forward selection mark (4)PHASE
CONTRAST/
Reverse selection mark (4)
BRIGHT
Front panel Function                     
Contentsbutton displayed
+Increase (to max. value)
4Forward the setting value
CUTO Selects CUT OFF setting screen
–Decrease (to min. value)
1Reverse the setting value
DRV Selects DRIVE setting screen
VOLUME/
SELECT (–)VOLUME/
SELECT (+) ●Parameters for PICTURE SUB ADJ., H. POSITION and V. POSITION can be set
separately depending on the signal (Input A (VIDEO), Input B (VIDEO) or Input B (Y/
C)) selected with the input select buttons on the front panel.
Select the required video input with the input select buttons on the front panel in
advance.
●WHITE BALANCE can be set independently at 6500 or 9300 for the color temperature
value.
Set COLOR TEMP. to 6500 or 9300 on the  screen beforehand.
●INPUT REMOTE is shown when REMOTE SYSTEM is set to MAKE.
Notes:
4PICTURE SUB ADJ.
H. POSITION :    00
V. POSITION :    00
WHITE BALANCE
CONTROL LOCK : OFF
STATUS DISPLAY : ON
REMOTE SYSTEM : MAKE
INPUT REMOTE : A – B1
23
4
PICTURE SUB ADJ.
H. POSITION
V. POSITION
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT  REMOTE
MENUCHROMA
PHASE
CHROMA
PHASE BRIGHTCONTRAST
VOLUME/SELECT
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 12
 
						

							ENGLISH
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
5. Press the MENU button to quit.
Notes:
●When the CONTROL LOCK function
is set to ON, pressing operation
buttons on the front panel will display
the message “CONTROL LOCK ON!”
on the screen for about 3 seconds.
●The CONTROL LOCK function is
maintained even when the power is
turned off.
●To turn off the CONTROL LOCK
function, while holding the MENU
button press the CHROMA/PHASE
button. Then set the CONTROL
LOCK function to OFF.
●Even when the CONTROL LOCK
function is set to ON, the following
operations are available:
–Power Switch operation
–Volume control with the VOLUME/
SELECT buttons
–Display or disappear of the  screen.
●The STATUS DISPLAY function can
be set to display (ON) or not display
(OFF) the present color system when
the power is turned on or the input
signal is changed. Refer to page 7 for
more information.
●When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A
and B buttons or the UNDER SCAN
button is pressed, “REMOTE ON!”
appears on screen for about 3
seconds. (Not shown with CONTROL
LOCK set to ON.)
●When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
●INPUT REMOTE and REMOTE
SYSTEM are enabled when
REMOTE ENABLE is set to ON.
Front panel Function                     
Contents
button displayed
MENU EXITQuit (or Release) the 
screenMENU
11
*1 May not be shown depending on the type of signals input.
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 15 for more details.
Note:
Setting Description
MAKE Make contact system: Controls the function using the control
terminal’s short-circuit and open (short-circuits or opens 15th
terminal (GND)).
TRG. Trigger system: Controls the function by short-circuiting (short-
circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-B Switches the input by short-circuiting a specified signal line in
INPUT A or B.
A/B Switches between INPUT A and INPUT B with D-sub pin 2.
Set-up menu items Purpose Settings
PICTURE SUB ADJ. Image sub adjustment Selects CONTRAST/BRIGHT/CHROMA/PHASE. The
selected setting screen is shown. Select the function display for
adjustment.
CONTRAST Adjusts contrast.
BRIGHT Adjusts brightness.
CHROMA Adjusts color density. *1
PHASE Adjusts hue. *1
H. POSITION Adjusts the horizontal position of the
screen (+: Horizontal position shifts
to the right/-: Horizontal position shifts to
the left)
V. POSITION Adjusts the vertical position of the screen
(+: Vertical position moves up/-: Vertical
position moves down)
WHITE BALANCE Adjusts the white balance. Selects the drive (DRV) or cut off (CUTO) adjustment. The selected
setting screen is shown. Select the function display for adjustment.
DRIVE R. DRIVE Adjusts red level.
B. DRIVE Adjusts blue level.
CUT OFF R. CUT OFF Adjusts red cut off.
G. CUT OFF Adjusts green cut off.
B. CUT OFF Adjusts blue cut off.
CONTROL LOCK Sets the operation buttons on the front
panel to control lock mode.
STATUS DISPLAYSets the status display of the color system.
REMOTE SYSTEM Sets the external control function method. *2
INPUT REMOTE Sets external control of input selection.
(Shown only when REMOTE SYSTEM is *2
set to MAKE.)
–
5      • • •      –
01       00      +
1      • • •      +
5
–
5      • • •      –
01       00      +
1      • • •      +
5
OFF
      ON
OFF
      ON
MAKE
      TRG.
A–B
     A/B
–
10      –
9           –
01    00     +
01          +
09     +
10• • • • 
–
10      –
9           –
01    00     +
01          +
09     +
10• • • • 
–
10      –
9           –
01    00     +
01          +
09     +
10• • • • 
–
10      –
9           –
01    00     +
01          +
09     +
10• • • • 
–
20     –1
9           –
01    00     +
01          +
19     +
20• • • • 
–
20     –1
9           –
01    00     +
01          +
19     +
20• • • • 
–
20     –1
9           –
01    00     +
01          +
19     +
20• • • • 
–
20     –1
9           –
01    00     +
01          +
19     +
20• • • • 
–
20     –1
9           –
01    00     +
01          +
19     +
20• • • • 
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 13
 
						

							12
Functions (Items)Initialization(setting)
SHARPNESS 00
ADJ. BAR POSI LOWER
COLOR TEMP 6500
COLOR SYSTEMAUTO
RUSH DELAY STD.
ASPECT RATIO 4 – 3
PICTURE SUB ADJ.
CONTRAST 00
BRIGHT 00
CHROMA 00
PHASE 00
H. POSITION 00
V. POSITION 00
WHITE BALANCE
         R. CUT OFF 00
G. CUT OFF 00
B. CUT OFF 00
R. DRIVE 00
B. DRIVE 00
CONTROL LOCK OFF
STATUS DISPLAY ON
REMOTE SYSTEM MAKE
INPUT REMOTE A – B
CHROMA 00
PHASE 00
CONTRAST 00
BRIGHT 00
VOLUME 20
 RESET
             Are   you     sure ?
“Yes”  then   
“No”   then   
Sorts
 screen
 screen
Volume
HOW TO INITIALIZE THE
SETTING
SCREEN DISPLAY AND SELECTIONS IN THE
 RESET MODE
You can set  and  screen items, picture adjustment items and
the volume level to their factory-set (initial) values.
1. Press the Power () switch to turn the power
OFF (activate the standby mode).
The  RESET screen is displayed.
Initial settings
  RESET screen
2. While pressing both MENU button and CHROMA/
PHASE button, press the Power (
) switch to turn
the power ON.
3. Setting
 Initialization is required.
 Initialization is not required.Press the VOLUME/SELECT [+] button.
* Initialization is completed, and the 
RESET screen disappears.
Press the MENU button.
* Initialization is aborted, and the 
RESET screen disappears.
●The  RESET screen will not be
displayed if the MENU or CHROMA/PHASE buttons are
pressed for a very short time. Keep pressing them until
the display screen appears.
Note:
POWER
MENUCHROMA
PHASEPOWER
MENU
VOLUME/SELECT
Picture adjustment
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 14
 
						

							ENGLISH
VIDEO A
AUDIO A
AUDIO B VIDEO B
IN OUT
IN
ININOUT
OUT
INOUT
Y/C
OUT
BASIC CONNECTION EXAMPLE
Notes:
•
 Before connecting your system, make sure that all units are turned off.• The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected.
Be sure to refer to the instructions provided with the unit(s) you are connecting.
• Each pair of input (IN) and output (OUT) terminals are bridge-connected.• If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)
terminal as this will cause the terminating resistance switch to open (auto terminate function).
• When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components.
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video
signal “looping” between the VCRs, and is not a malfunction.)
• Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When both VIDEO
B terminals are connected (input) at the same time, the Y/C terminal has priority.
VIDEO A Connection Example (Select Input A (VIDEO))
VIDEO B (VIDEO) Connection
Example (Select Input B (VIDEO))
Video Camera
Video Monitor
VCR
Video Camera
Video Monitor
VCRVideo(Video signal cable)
Audio
(Audio signal cable)
Video
(Video signal cable)
Audio
(Audio signal cable)
Audio
(Audio signal cable)
Video
(Video signal cable)
Video
(Video signal cable)
Video MonitorVCR
Video MonitorVCR
: Signal Flow
13
Audio
(Audio signal
cable)
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 15
 
						

							VIDEO B (Y/C) Connection Example (Select Input B (Y/C))
VIDEO A
AUDIO A
AUDIO B VIDEO B
IN OUT
IN
ININOUT
OUT
INOUT
Y/C
OUT
Video Camera
Video Monitor
VCRY/C (S-video)
(Y/C (S-video) signal cable)
Audio
(Audio signal cable)
Audio
(Audio signal cable)
Y/C (S-video)
(Y/C (S-video) signal cable)
Video MonitorVCR
BASIC CONNECTION EXAMPLE
(cont’d)
: Signal Flow
14
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 16
 
						

							ENGLISH
HOW TO USE EXTERNAL
CONTROL
ABOUT EXTERNAL CONTROL
This monitor is provided with an external control terminal. MAKE (make contact) or TRIG. (trigger) system can be selected by the
setting of REMOTE SYSTEM in the .
MAKE (make contact system) : The function is controlled by short-circuiting or disconnecting each control terminal with pin 15
(GND).
TRG. (trigger system) : The function is controlled by short-circuiting with pulses (for about 1 second) (short-circuit/open
with the 15th pin GND).
* The 14th pin (REMOTE ENABLE) is controlled with MAKE even though TRG. is selected.
Note:
●When this monitor is externally controlled, the following buttons are disabled.
MAKE: INPUT-A and B, UNDER SCAN on the front panel.
*1:OFF stands for disconnection, and ON stands for short-circuit.
*2:Do not connect.
*3:Setting REMOTE ENABLE to ON enables remote control from the REMOTE terminal.
*4:INPUT REMOTE setting in the set-up menu (REMOTE SYSTEM shown only when MAKE is selected.)
For the D-sub pins 2 and 3, 2-pin or 1-pin control can be set with INPUT REMOTE in the set-up menu.
•2-pin control: Only the specified signal line in INPUT-A or B is short-circuited.
•1-pin control: Switches between INPUT-A and INPUT-B only with the 2nd pin of the D-sub connector.
OFF : INPUT A
ON : INPUT B
The Names and Functions of Terminals
No. Names Functions Operations (OFF p[ ON)*1
1not used – – –*2
2INPUT A Changes the input to INPUT A Not change Change*4
3INPUT B Changes the input to INPUT B Not change Change*4
4not used – – –*2
5not used – – –*2
6not used – – –*2
7not used – – –*2
8not used – – –*2
9not used – – –*2
10 ASPECT Changes the screen ratio to 16:9 4:3 16:9
11 UNDER SCAN Makes the screen under-scan Over-scan Under-scan
12 not used – – –*2
13 not used – – –*2
14 REMOTE ENABLE Makes the external control from the Invalid Valid*3
REMOTE terminal valid or invalid
15 GND Used as a ground terminal – –
ConnectionsConnect (short-circuit) the 15th terminal (GND) to each of the 1st through 14th terminals in the
3-lines 15-pins D-sub connector. The functions of each terminal are listed below.
NOTES :
●When both INPUT A and INPUT B are selected (short-circuited) under the MAKE system, INPUT A has priority.
●To control INPUT A  and INPUT B in MAKE mode, we recommend using the interlock switch, which turns off a switch when
another switch is turned on.
To control INPUT A and INPUT B in TRG. mode, we recommend using the return switch, which stays ON while pressed.
12 3 10
8 9
6 7
11 12 1314 15
4 5
15
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 17
 
						

							Problems
No power supply.
No picture with the
power on.
No sound.
Shaking picture.
No colors, wrong
color, or dark picture.
Unnatural, irregularly
colored, or distorted
picture.
Dark stripes appear
at the top and bottom
of the screen, picture
vertically squeezed.
The overall picture
size is too small.
Function buttons on
the front panel do not
function.
The INPUT SELECT
buttons do not
function.
Points to be checked
Is the power plug loosened or disconnected?
Is the main power turned OFF?
Is the video signal output from the connected
component?
Is the input signal selected properly?
Is the video cable disconnected?
Is the audio signal output from the connected
component?
Is the volume output set to minimum?
Is the audio cable disconnected?
Is the monitor close to a device generating a
strong magnetic field?
Is the color system selected properly?
Has the picture control setting (CONTRAST,
BRIGHT, CHROMA or PHASE) been changed?
Is the monitor close to a speaker, magnet or any
other device generating a strong magnetic field?
Is the aspect ratio set to 16:9?
Has the UNDER SCAN button been pressed so
the UNDER SCAN button lights?
Has control of the buttons been locked? (Has
the CONTROL LOCK function been set to ON?)
Is input selection under external control? (Has
the REMOTE ENABLE function been set to
valid (ON)?)
Measures (Remedy)
Firmly insert the power plug.
Turn the main power ON. (See page 6.)
Set the connected component correctly.
Select the required video signal input with the
Input select button. (See page 7.)
Connect the video signal cable firmly.
(See pages 13 and 14.)
Set the connected component correctly.
Adjust the speaker volume with the VOLUME/
SELECT button. (See page 7.)
Connect the audio signal cable firmly.
(See pages 13 and 14.)
Move the device away from the monitor until the
picture stabilizes.
Set COLOR SYSTEM in the  screen to
AUTO. (See page 9.)
Set each picture control to the standard setting.
(See page 7.)
Move the device away from the monitor and turn
the monitor’s power off. Wait at least 30 minutes,
then turn the power on again.
Set ASPECT RATIO in the  screen to
[4 : 3 (4 – 3)]. (See page 9.)
When controlling externally, ASPECT RATIO
should be set to [4 : 3 (4 – 3)]. (See page 15.)
Press the UNDER SCAN button to turn off the
button. (See page 4.)
Set CONTROL LOCK in the 
screen to OFF. (See pages 10 and 11.)
Set REMOTE ENABLE to OFF (invalid).
(See page 15.)
TROUBLESHOOTING
Solutions to common problems related to your monitor are described here. If none of the solutions presented here
solves the problem, unplug the monitor and consult a JVC-authorized dealer or service center for assistance.
The following are not malfunctions:
●When a bright still image (such as a white cloth) is displayed for a long period, it may appear to be colored. This is due to the
structure of the cathode ray tube and will be deleted when another image is displayed.
●You experience a mild electric shock when you touch the picture tube. This phenomenon is due to a normal buildup of static
electricity on the CRT and is not harmful.
●The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality
appears on the screen as well.
●If two or more monitors are operated next to each other, their images may shake or be distorted. This phenomenon is due to
mutual interference; it is not a malfunction. Move the monitors away from each other until the interference disappears or turn the
power off on any monitor that is not being used.
16
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 18
 
						

							ENGLISH
SPECIFICATIONS
17
MODEL TM-H1900G TM-H1700G
TypeColor video monitor
Color systemPAL, NTSC (3.58)
Picture tube49 cm (19) measured diagonally, 44 cm (17) measured diagonally,
90° deflection, in-line gun, 90° deflection, in-line gun,
trio-dot type trio-dot type
(phosphor dot-trio pitch 0.27 mm) (phosphor dot-trio pitch 0.27 mm)
Effective screen sizeWidth 365.8 mm (14-5/8) Width 327.5 mm (12-7/8)
Height 274.3 mm (10-7/8) Height 246.2 mm (9-5/8)
Diagonal 457.2 mm (18) Diagonal 407.1 mm (16-1/32)
Scanning frequencyH: 15.734 kHz (NTSC), 15.625 kHz (PAL)
V: 59.94 Hz (NTSC), 50 Hz (PAL)
Horizontal resolution750 TV lines or more
(Y/C input mode)
Input terminals VIDEO AComposite video: 1 line, BNC connector x 2,
1 V(p-p),  75 Ω, negative sync
(bridge connection possible, auto termination)
VIDEO BComposite video: 1 line, BNC connector x 2,
1 V(p-p),  75 Ω, negative sync
(bridge connection possible, auto termination)
Y/C-separated: 1 line, mini-DIN 4-pin connector x 2
Y: 1.0 V (p-p), 75 Ω
C (BURST): 0.286 V (p-p), 75 Ω (NTSC) 0.3 V (p-p), 75 Ω (PAL)
(bridge connection possible, auto termination)
AUDIO A1 line (monaural), RCA pin x 2, 0.5 V(rms), high-impedance
(bridge connection possible)
AUDIO B1 line (monaural), RCA pin x 2, 0.5 V(rms), high-impedance
(bridge connection possible)
REMOTEPoint-of-contact connection, 1 line D-sub connector (15-pin, 3-line)
Audio power output1 W
Built-in speaker8 cm round x 1, impedance of 8 Ω
Environmental conditionsOperation temperature: 5°C – 40°C (41°F – 104°F)
Operation humidity: 20 % – 80 % (non-condensing)
Power requirements120 V/230 V AC, 50 Hz/ 60 Hz
Power consumption1.2 A (120 V AC)/0.8 A (230 V AC) 1.1 A (120 V AC)/0.7 A (230 V AC)
DimensionsWidth 440 mm (17-3/8) Width 395 mm (15-5/8)
Height 375 mm (14-7/8) Height 334 mm (13-1/4)
Depth 496 mm (19-5/8) Depth 418 mm (16-1/2)
Weight25.1 kg (55.2 lbs) 18.3 kg (40.3 lbs)
AccessoryAC power cord
* Illustrations used in this manual are for explanatory purposes only. The appearance of the actual product may differ slightly.
* Dimensions and weight are approximate.
*E. & O. E.  Design and specifications subject to change without notice.
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 19
 
						

							395 (15-5/8)418 (16-1/2)
407 (16-1/8)
68 
(2-3/4)286 (11-3/8)
3 (1/8)3 (1/8)
336.3 (13-1/4)*
288 (11-3/8)
ø20
 (7/8)
256 (10-3/8)*
334 (13-1/4)  117 (7)
1.5
 (1/16)
POWERCHROMA MENU
INPUT  SELECT UNDER
SCAN
PHASETM-H1700GBRIGHT CONTRAST VOLUME/SELECTAB
Dimensions
< Front View >< Side View >
Unit : mm (inch)
18
POWERCHROMAMENUINPUT  SELECTUNDER
SCANPHASETM-H1900GBRIGHTCONTRASTVOLUME/SELECTAB
440 (17-3/8)496 (19-5/8)
485 (19-1/8)
95.7
 (3-7/8)336 (13-1/4) 375 (14-7/8)
*
380.4 (15)
284.3 (11-1/4)
*
375 (14-7/8) 195.5 (7-3/4)
1.5
 (1/16)
5 (1/4)
5 (1/4)
ø20
 (7/8)
< Front View >< Side View >
[TM-H1900G]
[TM-H1700G]
Unit : mm (inch)
SPECIFICATIONS (cont’d)
*Asterisks (*) are used to indicate front panel
dimensions.
*Asterisks (
*) are used to indicate front panel
dimensions.
LCT1092-003A-H[EN]3.p6507.11.8, 4:49 PM 20