JVC Th A9 Instructions

47
4747 47
Limiting playback by children
Limiting playback by childrenLimiting playback by children Limiting playback by childrenEnglish
To temporarily release the Parental 
lock
When you set the parental level strictly, some discs may not be
played back at all. When you insert such a disc and try to play it,
the Parental Lock on-screen display appears on the TV, and the
unit will ask you whether you want the parental lock to be tempo-
rarily released or not.
1Use the 5
55 5/°
°° ° cursors to move the...

48
4848 48
English
nnAmplifier settings
Perform amplifier settings (balance, tone, speaker size and delay
time, crossover frequency, LFE (Low Frequency Effect) level and
dynamic range) for the powered sub-woofer unit to obtain opti-
mum listening performance.
Note:
• Before starting settings, be sure that each speaker is prop-
erly installed and your listening position is fixed, since
some setting items should be changed according to your
listening position with respect to the installed speakers.
Basic...

49
4949 49
Amplifier settings
Amplifier settingsAmplifier settings Amplifier settingsEnglish
Setting tone
Adjust the tone (bass and treble) for the front speakers.
1Press SETTING.
2Press the 5
55 5/°
°° ° cursors until “BASS” or “TRE-
BLE” appears on the display.
• After a while, the current setting value appears.
3Within 5 seconds, press the 2
22 2/3
33 3 cursors to
adjust the bass or treble.
Each time you press the button, the setting value changes 2
steps at a time between –10 and +10. (0: flat...

50
5050 50
Amplifier settings
Amplifier settingsAmplifier settings Amplifier settings
EnglishAdjusting crossover
When using a small speaker with weak bass as a front, center, or rear
speaker, you can redirect bass audio to the sub-woofer. Select a cross-
over frequency to match the size of the small speaker being used.
• When you use the supplied speakers with this system, set the
crossover frequency as follows:
CROSSOVER: 200Hz
1Press SETTING.
2Press the 5
55 5/°
°° ° cursors until “CROSSOVER”
appears...

51
5151 51
EnglishnnSound settings
You can adjust the sub-woofer output level, output level of each
speaker using a test tone, and DSP effect, to obtain preferable
sound for you.
Note that you need to adjust them at the position you will listen to.
Adjusting sub-woofer level
You can adjust the sub-woofer output level to increase or decrease
the sound volume from the sub-woofer.
1Press SOUND.
The system enters sound setting mode.
2Press SUBWOOFER +/– to adjust the level.
You can adjust the sub-woofer...

52
5252 52
Sound settings
Sound settingsSound settings Sound settings
EnglishAdjusting DSP effect
You can adjust the strength of DSP (Digital Signal Processor) ef-
fect for each DAP mode so that you can customize sound effect.
About the DAP, see “Using the DSP Modes [DSP MODE]” on
page 20.
1Press DSP MODE to select one of DSP
modes.
The current DSP mode appears on the display window. Each
time you press the button, DSP mode changes as follows.
=
== =
SURROUND ON*=
== =
 THEATER =
== =
 LIVE CLUB =
== =...

53
5353 53
EnglishnnAV COMPU LINK remote control system
The AV COMPU LINK remote control system allows you to operate JVC video components (TV and VCR) through the
center unit.
To use this remote control system, you need to connect the video components you want to operate, follow the diagrams and procedure ex-
plained here.
Connection and setup
When connecting to a TV
Connect the center unit to a TV via the AV COMPU LINK terminals.
Then, set the AV COMPULINK setting of the center unit as follows.
• When...

54
5454 54
AV COMPU LINK remote control system
AV COMPU LINK remote control systemAV COMPU LINK remote control system AV COMPU LINK remote control system
EnglishOperation
You can enjoy pictures and/or sound by just putting a source com-
ponent (which plays back the pictures and/or sound such as the
center unit or a VCR) into play mode. You do not have to operate
the TV including not having to perform power switching.
1Turn on the main power of the TV.
2Insert a disc into the source component.
3Press PLAY...

55
5555 55
EnglishnnOperating Other Manufacturers’ Video Equipment
This remote control supplied with the receiver can transmit control
signals for other manufacturers’ VCRs, TVs, CATV converters
and DBS tuners. By changing the transmittable signals from preset
ones to the other manufacturers’, you can operate the other manu-
facturer’s components using this remote control.
When operating the other manufacturers’ components, refer also
to the manuals supplied with them. To operate these components
with...

56
5656 56
Operating Other Manufacturers’ Video Equipment
Operating Other Manufacturers’ Video EquipmentOperating Other Manufacturers’ Video Equipment Operating Other Manufacturers’ Video Equipment
English
To change the transmittable signals for oper-
ating a CATV converter or DBS tuner
1Slide the remote control mode to “CATV/
DBS.”
2Press and hold TV/CATV/DBS  .
Keep press until step 4 is finished.
3Press TV.
4Enter manufacturer’s code (2 digits) using
buttons 1 - 9, and 0.
See the list below to find...