JVC Rx 5052 S Manual

29
Operating Video Components
VCR
You can always perform the following operations:
STANDBY/ON 
 VCR: Turn on or off the VCR.
VCR CH +/–:Change the TV channels on the VCR.
After pressing VCR, you can perform the following operations on
the VCR:
3:Start playing.
REW:Rewind the tape.
FF:Fast-forward the tape.
7:Stop playing, recording, rewind and fast forward.
8:Pause playing and recording. To resume, press 3.
REC PAUSE:Enter recording pause.
To start recording, press this button then 3.
DVD player
You can...

30
Operating Other Manufacturers’ Video Equipment
This remote control supplied for the receiver can transmit control signals for other manufacturers’ TVs, CATV
converters, VCRs and DVD players.
When operating the other manufacturers’ components, refer also to
the manuals supplied with them.
•After replacing batteries for the remote control, you need to set the
manufactures’ codes again.
To change the transmittable signals for
operating another manufacturer’s TV
1 Set the TV/CATV selector to “TV.”
2 Press...

31
To change the transmittable signals for
operating another manufacturer’s DVD player
1 Press and hold STANDBY/ON  DVD.
2 Press DVD.
3 Enter a manufacturer’s code using buttons 1 – 9,
and 0.
Manufacturer Codes
JVC 01*
Panasonic 02
Philips 04
Pioneer 03
Sony 05
Toshiba 06
Yamaha 07
*“01” is the initial setting.
4 Release STANDBY/ON  DVD.
Now you can perform the following operations on the DVD
player:
STANDBY/ON 
 DVD:Turn on and off the DVD player.
After pressing DVD, you can perform the following...

32
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC’s
service center.
SOLUTION
Plug the power cord into an AC outlet.
Check speaker wiring and reconnect if necessary.
(See page 5.)
Press SPEAKERS ON/OFF so that the sounds
come out of the speakers. (See page 11.)
Select the correct source.
Press MUTING to cancel the mute. (See page 13.)
Select the correct input mode (analog or digital).
(See pages 11 and 12.)
If...

33
Specifications
Amplifier
Output Power
At Stereo operation
Front channels:
100 W per channel, min. RMS, driven into 8 Ω,
40 Hz to 20 kHz with no more than 0.8% total
harmonic distortion.
At Surround operation
Front channels: 100 W per channel, min. RMS, driven into 8 Ω, at 1 kHz with no
more than 0.8% total harmonic distortion.
Center channel: 100 W, min. RMS, driven into 8 Ω, at 1 kHz with no more than 0.8%
total harmonic distortion.
Surround channels: 100 W per channel, min. RMS, driven into 8 Ω, at...

34
FM tuner (IHF)
Tuning Range: 87.5 MHz to 108.0 MHz
Usable Sensitivity Monaural: 12.8 dBf (1.2 µV/75 Ω)
50 dB Quieting Sensitivity Monaural: 16.0 dBf (1.7 µV/75 Ω)
Stereo: 37.5 dBf (20.5 µV/75 Ω)
Stereo Separation at OUT (REC): 35 dB at 1 kHz
AM tuner
Tuning Range: 530 kHz to 1 710 kHz
General
Power Requirements: AC 120V, 60 Hz
Power Consumption: 200 W/260 VA (at operation)
2 W (in standby mode)
Dimensions (W x H x D): 435 mm x 146.5 mm x 369.5 mm
(17 
3/16 in. x 5 13/16 in. x 14 5/8 in.)
Mass: 7.5 kg...

warranty.p6504.11.24, 11:48 AM 2 

warranty.p6504.11.24, 11:48 AM 1 

1204RYMMDWJEIN EN
© 2005 Vicotor Company of Japan, Limited
AUDIO/VIDEO CONTROL RECEIVER
RX-5050B/RX-5052S
Cover_RX-5050&5052[J]4.p6504.11.23, 0:30 AM 2