JVC Projector DLA-RS600 User Manual

Whole Adjust (Pixel) Operation Procedure
For making general adjustments to slight color fringing in the horizontal/vertical directions of the video image.
A Set “Adjust Area” to “Whole”
B Select “Adjust Color” and “Adjust Pattern Color”
C Select “Adjust (Pixel)”, and press the [OK] button
0 The selected adjustment pattern and Adjustment (Pixel) window are displayed.
. D
Press the [OK] button to enter the Adjustment mode
E Use 
the [JKH  I] keys to move and adjust the pixels in the vertical and horizontal...

Whole Adjust (Fine) Operation Procedure
For making general adjustments on the misalignment of the entire screen using “Adjust (Pixel)”, followed by making
fine adjustments.
A Set “Adjust Area” to “Whole”
B Select “Adjust Color” and “Adjust Pattern Color”
C Select Adjust (Fine), and press the [OK] button
0 The selected adjustment pattern and Fine window are displayed.
0 The adjustable range may be smaller depending on the pixels being adjusted on the entire screen.
. D
Press the [OK] button to enter the...

Zone Adjust Operation Procedure
For fine-tuning misalignments on a part of the screen after adjusting the overall screen misalignment using “Adjust
(Pixel)” and “Adjust (Fine)”.
0 The screen can be divided vertically and horizontally into 10 sections for partial adjustments to be made.
A Set “Adjust Area” to “Zone”
B Select “Adjust Color” and “Adjust Pattern Color”
C Select Adjust (Fine), and press the [OK] button
0 The selected adjustment pattern and Zone Adjustment window are displayed.
0 The...

Display Setup
Back Color
For setting the color of the background to “Blue” or “Black” when there is no signal input. Menu Position
For setting the display position of the menu. Signal Display
Setting
Description
On Shows the input terminal for 5 seconds when input is switched.
Off Not displayed.Logo
Setting
Description
On Displays the “D-ILA” logo for 5 seconds during startup.
Off Not displayed.Language
For setting the display language to “ 日本語”, “English”, “Deutsch”, “Español”, “Italiano”, “Français”,...

ECO Mode
Setting
Description
On Enables “ECO Mode” to minimize power consumption in the Standby mode.
0 RS-232C / LAN communication cannot be used in the Standby mode.
0 If there is no signal transmission and operation for 20 minutes while an image
is 
projected, the power management switches the equipment automatically into
standby mode.
Off Select this option to control via RS-232C / LAN communication in the Standby
mode or if Control4 is to be used.Network
Specify the settings below during external...

Remote Code
For changing the remote control code. 0 You need to configure the remote control according to the settings of this unit.
On the remote control unit, press the [MENU] and [BACK] buttons at the same time for three seconds or longer to
switch the code.
0 The backlight of the remote control blinks 3 times: change the remote control code to “A”
0 The backlight of the remote control blinks 2 times: change the remote control code to “B” Setting
Description
A Change the remote control code from “B”...

Replacing the Lamp
The lamp is a consumable item. If the image appears dark or the lamp goes out, replace the lamp unit.
0 When the lamp replacement time approaches, the user is notified with a message displayed on the screen and by
the indicator. (
P. 74)Lamp Replacement Procedure
CAUTION
0 Do not insert your hands into the lamp compartment.
This could cause significant deterioration in the
performance of the equipment, or lead to injury and
electric shock.
0 Do 
 not replace the lamp immediately after...

5
Install the new lamp unit
. 6
Tighten the screws of the new lamp
unit 0 Tighten the screws with a  t screwdriver.
. 7
Attach the lamp cover
0 Insert the two tabs at the top and bottom of the
lamp cover into the unit.
0 Tighten the screws with a t screwdriver.
. MEMO
Usable lamp life 0 When the lamp is used with “Lamp Power” set to
“Low”, 
the lamp life on this unit is approximately 4500
hours. This is the average usable time and not a
guaranteed value.
0 The 
 lamp life may not reach 4500 hours...

Resetting the Lamp Time
Reset the lamp time when you have replaced the lamp.
It provides an estimated timing for lamp replacement Resetting the lamp time from the menu
screen 1
Press the [MENU] button to display
the menu 2
Select “Function”
"“Lamp Reset”
from the menu
. 3
On the “Reset Lamp Time?” screen,
select  “Yes” and press the [OK] button
0 The lamp time is reset to zero.
. Resetting the lamp time using the remote
control 1
Insert the power plug into the power
outlet 2
Make sure that you...

Cleaning and Replacing the Filter
Clean the filter regularly Otherwise, the air intake
efficiency may deteriorate, and malfunction may occur. CAUTION
0 Make sure that you pull out the power plug from the
outlet before cleaning or replacing the filter.
0 Before  turning this unit upside down and placing it on
the floor or a table, make sure that you lay a soft rag
in advance to prevent the projector from being
scratched. 1
Remove the inner filter
. 2
Clean the filter
. 0
Wash the filter with water and dry...