JVC Projector Dla Rs2 Instructions Manual

21
Getting Started PreparationBasic OperationSettings Troubleshooting Others
ENGLISH
bAdjust the focus
c Adjust the image size (zoom)
d To end
FTurn off the power
zSwitches between “Focus” and “Zoom”  whenever the [ENTER] button is 
pressed.
zThe power cannot be turned off withi n approximately 90 seconds after it 
has been turned on. Start operation only after 90 seconds time. 
zYou can also press the [STANDBY/ON] button on the unit to turn off the 
power. ( pP11 )
zPut back the lens cap after use to...

22
3Basic Operation
Convenient Features during Projection
The projected image can be set to a most appropriate screen size (aspect 
ratio). 
z
The screen size can also be set from “Aspect” of the setting menu. (pP29 -  S)
zWhen high definition images are input,  the “V-Stretch” setting will be available 
instead. ( pP29 -  T)
zWhen PC signals are input, the “Resize” setting will be available instead.       
(p P29 -  U)
„Input Image and Projected Image by Different Screen Size Settings
z
Depending on the...

23
Getting Started PreparationBasic OperationSettings Troubleshooting Others
ENGLISH
BMask the image
aDisplay the setting menu
b Select “Setup”  g “Mask”
c Set a mask value
CTo end
zMasking is available only when high 
definition images are input.
MEMO
Setup
Image Source Install. Func. Info.
Image Adjust
Color Temp.
Gamma
Offset
Pixel AdjustMENU
Image Profile
Profile Memory
Picture Position
HDMI Input Level
Mask
Setup
Image Source Install. Func. Info.
2.5%
5%
Off
Overscan
ENTER
B CONFIRM
A
SELECT
ENTER...

24
4Settings
Setting Menu
Example:When changing “Aspect” from “4:3” to “16:9”
ADisplay the setting menu
BSelect “Source”  g “Aspect”
CSet to “16:9”
DTo end
Projected images can be adjusted to a desired view by changing the default settings.
Procedures for Menu Operation
PROJECTOR
OPERATE
LIGHT
TEST EXIT
SHARP
-
SHARP+
USER2
S-VIDEO
VIDEO ASPECT HDMI 2
OFF........ ........
HDMI 1 COMP.
N
NATURAL
CINEMA DYNAMIC
COLOR
TEMP
GAMMA
USER
3
D
COLOR-
COLOR+
USER1
C
CONTRAST
BRIGHT
HIDE INFO
MENU
ENTER
ON
MENU...

25
ENGLISH
Getting Started Preparation Basic OperationSettingsTroubleshooting Others
Item values shown in   are factory settings.
zItems that can be configured differ according to the input signals.
z“Contrast”, “Brightness”, “Color” an d “Sharpness” can also be configur ed from the remote control. (pP12 )
z“Tint” can only be adjusted when NTSC signals are input to the video or S-video input terminal.
* The red, green and blue colors can be  adjusted and registered respectively.
zThis setting can also be...

4
26
Setting Menu (Continued)
Settings
z
“Normal” is suitable for normal circumstances but other se ttings can be selected according to your preferences.
zThis setting can also be configured from the remote control. (pP12 )
* “Gamma Adjust”
A Select the reference gamma curve coefficient (1.8  f 2.6) in “Correction Value”.
B Select the color to be adjusted  in the gamma adjustment screen.
D To end
zIf gamma curve is adjusted repeatedly, calculation errors  will be accumulated and the gamma curve may not...

27
ENGLISH
Getting Started Preparation Basic OperationSettingsTroubleshooting Others
zThe horizontal and vertical directions are reversed when the im age is flipped to the left or right, or flipped up or down.
zTo adjust, use still images with distinct outlines.
zAs the adjustments are minor,  the effect may be difficult to see for some images.
zThis setting can also be configur ed from the remote control. (pP12 )
z“Contrast”, “Brightness”, “Color”, “Sharpne ss”, “DNR”, “Color Temp.”, “Gamma” and “O...

4
28
Setting Menu (Continued)
Settings
z
The display position value varies with the input signal.
zThis adjustment is available for analog input signals, or for  COMPONENT and HDMI-1/2 input signals when “V-Stretch” is set to 
“On”.
zThis setting is available only when projecting the HDMI input.
zMasking is available only when high definition images are input.
zThis setting is not available when PC signals are input to HDMI terminal.
zThis setting is available only when projecting the component video...

29
ENGLISH
Getting Started Preparation Basic OperationSettingsTroubleshooting Others
zThis setting can also be configur ed from the remote control. (pP12 , 22 )
zThis setting is not available when PC signals are input to HDMI terminal.
Source > Aspect (When SD video signals are being input)
S Aspect
Configures the screen size (aspect ratio) of the projected image.
4:3 Sets screen size of the projected image to 4:3.
16:9 Sets screen size of the projected image to 16:9.
Zoom Zooms the image.
Source >...

4
30
Setting Menu (Continued)
Settings
z
This setting is available only when projecting the video or S-video input.
zThis setting can only be adjusted  when NTSC signals are input to t he video or S-video input terminal.
Source > Color System
WColor System
Configures the color system.
Auto Configures the color system automatically.
NTSC Select this when the color system is NTSC.
NTSC4.43 Select this when the color system is NTSC4.43.
PAL Select this when the color system is PAL.
PAL-M Select this when...