JVC Projector Dla Hd350bu Instructions Manual

							
 
 
ENGLISH
1
Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

                                  
● Set “COMP.” in the setting menu to “SCART”.(P33 - 12 )
   
● Set “COMP.” in the setting menu to “RGB”.(P33 - 12 )
● For information on compatible input signals, see “Specifications”. (P56)
HDMI 1HDMI 2S-VIDEORS-232CYRVIDEOSYNCCB/PBCR/PRBG
This unit
To RGB video input terminals
RGB video cable(sold separately)R(Red)
B(Blue)
G(Green)(Includes sync signals)
RGB video output terminals
Device equipped with RGB output
HDMI 1HDMI 2VIDEOS-VIDEORS-232CYRSYNCCB/PBCR/PRBG
This unit
DVD player for European market
SCART terminal 
SCART-RCA cable (sold separately)
To RGB video and sync signal input terminals
  Connecting via SCART-RCA Cable 
  Connecting via RGB Video Cable  
						

							
2Preparation


Installing the Projector and Screen 
While installing, please place this unit and the screen perpendicular to\
 each other. Failing to do so may 
increase trapezoidal distortion. Please refer to “Keystone”. (P36 - 24 )
 
 ● The angle range which can be set for this unit is ±10°.
  
 ● Malfunctions may occur if the angle is not set within the above-mentioned range.
      
1 Installing the projector and screen
      ■ Left/Right position
         * 0% up/down position (center)
      ■ Up/Down position
         * 0% left/right position (center)
            
      ■ Shifting range of projected image
10°
10°
10°
10°
80%
34%34%
80%
Lens center
Approximately 34% (maximum) of the projected image 
Approximately 34% (maximum) of the projected image 
Approximately 80% (maximum) of the projected image 
Approximately 80% (maximum) of the projected image
  Set Angle 
  Shift Adjustment   
						

							
 
 
ENGLISH

Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

2 Adjust such that the projected image is in the center of the screen
● It may be necessary to set “Pixel Adjust” in the setting menu after adjusting the image position. (P36 - 22 )
Determine the distance from the lens to the screen to achieve your desired screen size. 
This unit uses a 2.0x power zoom lens for projection. 
■ Relationship Between Projection Screen Size and Projection Distance
Projection Screen Size
(Diagonal Length) 
Aspect Ratio 16:9 
Approximate Projection Distance
W(Wide) to T(Tele)
Projection Screen Size
(Diagonal Length) 
Aspect Ratio 16:9 
Approximate Projection Distance
W(Wide) to T(Tele)
60"
(Approx. 1.52m) Approx. 1.78m to Approx. 3.66m10"
(Approx. 3.56m)Approx. 4.23m to Approx. 8.60m
0"
(Approx. 1.78m)Approx. 2.09m to Approx. 4.28m150"
(Approx. 3.81m)Approx. 4.53m to Approx. 9.22m
80"
(Approx. 2.03m)Approx. 2.40m to Approx. 4.89m160"
(Approx. 4.06m)Approx. 4.84m to Approx. 9.84m
90"
(Approx. 2.29m)Approx. 2.70m to Approx. 5.51m 10"(Approx. 4.32m) Approx. 5.14m to Approx. 10.45m
100"
(Approx. 2.54m)Approx. 3.01m to Approx. 6.13m180"
(Approx. 4.57m) Approx. 5.45m to Approx. 11.07m
110"
(Approx. 2.79m)Approx. 3.31m to Approx. 6.75m190"
(Approx. 4.83m) Approx. 5.75m to Approx. 11.68m
10"
(Approx. 3.05m)Approx. 3.62m to Approx. 7.36m 00"(Approx. 5.08m) Approx. 6.06m to Approx. 12.30m
10"
(Approx. 3.30m)Approx. 3.92m to Approx. 7.98m
● The projection distances in the table are provided only as a guide. Use them as a reference during installation.
● To adjust the installation, use a projected image of aspect ratio 16:9.
 Adjust the image position  to the center of the screen by pressing  (the up, down, left and right buttons).
BACKBackOperateSelectExitMENU
Focus
Lens Control
BACKBackOperateSelectExitMENU
Zoom
Lens Control
BACKBackOperateSelect
Shift
Lens control
LENS
LENS
LENS1


 
  Screen Size and Projection Distance      
						

							
3Basic Operation


Projecting Image 
This section describes the basic operations to project input images on t\
he screen. 
Preparation
1 Insert the power plug to the power 
      outlet
2 Turn on the power
    
    ● You can also press the        button on the unit to turn on the power.
                 (P15)
             ● The lens cover will be opened.
3 Project the image
     1 Select input mode
                                        
 ● You can also select the input mode by pressing theINPUTbutton on the 
      unit. (P15)
      Play back the selected device
4  Adjust the position of the projection 
       screen 
●  See “Installing the Projector and Screen” (P22) and “Lens 
     Control” (P36 - 21 ) for the adjustment method.
5 Adjust the image size (zoom) and the
       focus
     1 Adjust the focus
  WARNING
LAMP
ST ANDBY/ON
① Connect to this unit
② Connect to the power outlet
Light on (Green)
 Adjust accordingly by pressing  the up/down buttons
Power Cord
(Supplied)
Light on (Red)
ONBACK
TESTHIDE
BRIGHTCONTSHARP
COLORTINTN.R
GAMMAC.TEMP
INFOLENS.APASPECT
LENSINPUT
STANDBYON
MENU
CINEMA1CINEMA2
NATURALSTAGEDYNAMIC
USER1USER2USER3
LIGHT
RM-MH2GB
BACKBackOperateSelectExitMENU
Focus
Lens Control
①②
STANDBY/ON
STANDBY/ON
   HDMI 1      HDMI 2   　 COMP．     Video      S-Video
LENS
INPUT          
						

							
 
 
ENGLISH
5
Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

       Adjust the image size (zoom)
● Every time the LENS button is pressed, the adjustment item will be switched among “Focus”, “Zoom” and “Shift”. 
     FocusZoomShiftLENS                    
      To end
6  Turn off the power
     
● When power off, the lens cover will be closed.
● The power cannot be turned off within approximately 90 seconds
    after it has been turned on. Start operation only after 90 seconds 
    time.
● You can also press the button on the unit to turn off the 
    power. (P15)
● Pull out the power plug when the unit will not be used for a 
    prolonged time.
BACK
You can hide the image temporarily 
You can hide the image temporarily. 
● Press the HIDE button again to display 
         image.
● The power cannot be turned off when the  
           image is temporarily hidden. 
About Cool Down mode 
● The Cool Down mode is a function to 
      cool down the lamp for approximately 60 
      seconds after projection is complete. This 
      function prevents the internal parts of the 
      unit from deformation or damage due to 
      overheating of the lamp. It also prevents 
      lamp blowout and premature shortening 
      of lamp life.
● During Cool Down mode, the [STANDBY/ 
      ON] indicator blinks in red. 
●  After the Cool Down mode is complete, 
      the unit automatically returns to standby 
      mode. 
● Do not pull out the power plug during 
     Cool Down mode. This may shorten the 
     lamp life and cause a malfunction. 
HIDE
Adjust accordingly by pressing the up/down buttons 
Green light blinks when the image is hidden.

BACKBackOperateSelectExitMENU
Zoom
Lens Control
Blinking (Red Lamp)
Light on (Red Lamp)
While a confirmation screen is displayed
Cool Down mode
LENS
MEMO
TIPS      
						

							
3Basic Operation
6

Convenient Features during Projection 
You can change the screen size of the projected image or hide the surroun\
ding area of an image for which 
quality at the outer area has deteriorated.
The projected image can be set to a most appropriate screen size
(aspect ratio).
● The screen size can also be set from “Aspect(Video)” of the setting menu.
      (P34 - 14 )
● When PC signals are input, the “Aspect(Computer)” setting will be available  
      instead. (P34 - 15 )
■ Input Image and Projected Image by Different Screen Size 
     Settings 
Input ImageScreen Size
:
16:9Zoom 
      SDTV(4:3)Aspect Ratio:SameMost appropriate screen size
Aspect Ratio: LandscapeImage is stretched horizontally
Aspect Ratio:SameTop and bottom of the image are missing
      SDTV(4:3)Image recorded in landscape (black bands on top and bottom) of DVD software
Aspect Ratio:Same Small image is projected 
Aspect Ratio: Landscape Image is stretched horizontally
Aspect Ratio: Same Most appropriate screen size
● Depending on the input image, selecting “ :” may result in a vertically 
        stretched image, while selecting “16:9” provides you with the most 
      appropriate screen size.
Images for which quality at the outer area has deteriorated can be proje\
cted by masking (hiding) the surrounding area of the projected image.
1 Project the image 
ASPECT4:3     16:9      zoom      
    
Image for which quality at the outer area has deteriorated. 
BACK
TESTHIDE
BRIGHTCONTSHARP
COLORTINTN.R
GAMMAC.TEMP
INFOLENS.APASPECT
LENSINPUT
STANDBYON
MENU
CINEMA1CINEMA2
NATURALSTAGEDYNAMIC
USER1USER2USER3
LIGHT
RM-MH2GB
  Setting the Screen Size 
  Masking the Surrounding Area of an Image   
						

							
 
 
ENGLISH

Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

2 Mask the image   
    
     1 Display the setting menu
      Select “Input Signal”  “Mask” 
      Set a mask value
Example: 
When the “Mask” value is  
changed from “Off”  “5%”
3 To end 
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500K
2
Normal
Picture ModeContrastBrightnessColorTintColor Temp.GammaAdvancedLens Aperture
 Picture AdjustNatural
Reset
Video/S-VideoCOMP.
Aspect（Video）Aspect（Computer)V-stretchPicture PositionOver scan
Film Mode
ExitMENUBACKBackSelectOperate
HDMI
16:9Auto
Auto
Off
Off
MaskOff5%Off
2.5%
Input Signal
      自动
ExitMENUBACKBackSelectOperate
Off
Off5%
16:9Video/S-VideoCOMP.
Aspect（Video）Aspect（Computer)V-stretchPicture PositionOver scan
Film Mode
HDMI
Auto
AutoMask5%2.5%Off
Input Signal
● Masking is available only when high 
       definition images are input. 
MENU
①Select
②Confirm
①Select
②Confirm
MEMO      
						

							
4Settings
8

Setting Menu 
Projected images can be adjusted to a desired view by changing the initi\
al settings.
Example: 
  When changing “Aspect(Video)” from “:” to “16:9”
1 Display the setting menu
2 Select “Input Signal”  “Aspect(Video)”
3  Set to “16:9”
4  To end
MENU
MENUExitBACKBackSelectOperate
   0   0   0   06500K
2
Normal
Picture ModeContrastBrightnessColorTintColor Temp.GammaAdvancedLens Aperture
 Picture AdjustNatural
Reset
4:34:316:9Zoom
ExitMENUBACKBackSelectOperate
Off
Off5%
Video/S-VideoCOMP.
Aspect（Computer)Aspect（Video)
V-stretchPicture PositionOver scan
Film Mode
HDMI
Auto
AutoMask
Input Signal
4:316:916:9Zoom
ExitMENUBACKBackSelectOperate
Off
Off5%
Video/S-VideoCOMP.
Aspect（Computer)Aspect（Video)
V-stretchPicture PositionOver scan
Film Mode
HDMI
Auto
AutoMask
Input Signal
MENU
BACK
TESTHIDE
BRIGHTCONTSHARP
COLORTINTN.R
GAMMAC.TEMP
INFOLENS.APASPECT
LENSINPUT
STANDBYON
MENU
CINEMA1CINEMA2
NATURALSTAGEDYNAMIC
USER1USER2USER3
LIGHT
RM-MH2GB
①Select
②Confirm
①Select
②Confirm
  Procedures for Menu Operation      
						

							
 
 
ENGLISH
9
Getting Started
Preparation
Basic Operation
Troubleshooting
Settings
Others

Item values shown in  are factory settings.
● Items that can be configured differ according to the input signals.
Picture Adjust 
01 Picture Mode
Adjusts the pattern of the projected image.
Cinema 1, Cinema 2, Natural, Stage, Dynamic, User 1, User 2 and User 3.
02 Contrast
Adjusts the contrast of the projected image.
(Black) –50 to 50 (White)
03 Brightness
Adjusts the brightness of the projected image. 
(Darken) –50 to 50 (Brighten)
04 Color
Adjusts the color density of the projected image. 
(Lighten) –50 to 50 (Darken)
05 Tint
Adjusts the hue of the projected image. 
(Red) –50 to 50 (Green) 
● “Contrast”, “Brightness”, “Color” and “Tint” can also be configured from the remote control. (P16)
  Setting Menu  
						

							
4Settings
0

Setting Menu (Continued)
Picture Adjust > Color Temp.
06 Color Temp.
Sets the color temperature of the projected image.
5800KSelect this to give a reddish tinge to the 
image.
Only offset can be set.
6500KSelect this to have a balanced image.
7500KSelect this to give a bluish tinge to the 
image.
9300KSelect this to give a greater bluish tinge 
than 7500K.
High BrightSelect this to get the brightest image.
Custom 1
Gain
(Bright part)
Red(Less red) –255 to 0 (More red)
Green(Less green) –255 to 0 (More green)
Blue(Less blue) –255 to 0 (More blue)
Offset
(Dark part)
Red(Less red) –50 to 50 (More red)
Green(Less green) –50 to 50 (More green)
Blue(Less blue) –50 to 50 (More blue)
Custom 2
Gain
(Bright part)
Red(Less red) –255 to 0 (More red)
Green(Less green) –255 to 0 (More green)
Blue(Less blue) –255 to 0 (More blue)
Offset
(Dark part)
Red(Less red) –50 to 50 (More red)
Green(Less green) –50 to 50 (More green)
Blue(Less blue) –50 to 50 (More blue)
Custom 3
Gain
(Bright part)
Red(Less red) –255 to 0 (More red)
Green(Less green) –255 to 0 (More green)
Blue(Less blue) –255 to 0 (More blue)
Offset
(Dark part)
Red(Less red) –50 to 50 (More red)
Green(Less green) –50 to 50 (More green)
Blue(Less blue) –50 to 50 (More blue)
● The red, green and blue colors can be adjusted and registered respectively.
● This setting can also be configured from the remote control. (P16)