JVC Projector Dla Hd2ku Instructions Manual

							21
ON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
LAMPTEMPSTAND BYOPERATE
PRESET
MENUEXIT
ENTER
HIDE
5-1
5-1
4 4
LAMP TEMP STAND BYOPERATE
4Hiding the image temporarily
Press [HIDE]
●
The displayed image will disappear.
● Press [HIDE] again to restore the image.
5Turning off the power
1
Press the [OPERATE] button on this unit (or the [OPERATE
OFF] button on the remote control unit) for 1 second or more
● The [OPERATE] indicator turns off, the [STAND BY] indicator starts
blinking and this unit switches to the cool down mode. The cool down
mode is to allow the temperature of the light source lamp to cool off.
(☞  Page 11)
Note
● The [OPERATE OFF] button will not work within approximately 1 minute
after the light source has been turned on. Start operation only after 1
minute’s time.
Note
●Do not pull out the plug when the [STAND BY] indicator is blinking.
This may shorten the lamp life and cause a malfunction.
2Pull out the power plug from the power outlet
Indicators on this unit Light off Blinking 
						

							22
Image adjust
Set up
Options
InformationGREENGREENBLUEBLUE
REDRED
GammaGammaNORMALACUSTOMBColor tempColor temp.
Test patternUSER2USER1 D65
ENTERENTER
Image adjust
Options
InformationMenu PositionMaskMaskOff5% 2.5%Source50P 60PSet up
Image adjust
Set up
InformationPicture ShiftPicture ShiftSleep timeSleep time
Flip V Men
Menu display15secOnOnOff
15min15minOffOff30min30min60min60min960019200
On
0OffFlip H
RS232C(bps)
RS232C(bps)
Options
Image adjust
Set upLamp Lamp TimeTime905h
OptionsInformation
Set upOptions
InformationGREENGREENBLUEBLUE
REDREDColor tempColor temp.
Test patternUSER2USER1 D65
ENTERENTER
GammaGammaImage adjust
Set upOptions
InformationGREENGREENBLUEBLUE
REDREDColor tempColor temp.USER2USER1 D65
Test patternENTERENTER
Image adjust
Image adjust
Options
InformationMaskMaskOff5% 2.5%Source50P 60PSet up
Menu Position
Image adjust
Set up
InformationPicture Shift
Sleep timeSleep time
Flip VOnOff
15min15minOffOff30min30min60min60min960019200
On
0OffFlip H
RS232C(bps)
RS232C(bps)
Options
MenMenu display15secOn
*1
NORMALACUSTOMB
GammaGammaNORMALACUSTOM B
The menus displayed on the screen are used to perform adjustment and setting for this unit.
Menu Structure
The menus of this unit have the following structure.
Adjustments and Settings Using Menus
Main MenuSubmenu (Setting Menu)
1“Image adjust” Menu
2“Set up” Menu
3 “Options” Menu
4 “Information” MenuE.g.: “Gamma” Setting Menu
E.g.: “Test pattern” Setting Menu
E.g.: “Menu Position” Setting Menu
E.g.: “Menu display” Setting Menu
*1 Press the [ENTER] button to switch to the test pattern image. There are 10 types of test patterns. Press the [ENTER]
or [TEST] buttons to alter the test pattern to be projected. 
						

							23
ON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
LAMPTEMPSTAND BYOPERATE
PRESET
MENUEXIT
ENTER
HIDE
MENUMENU
ENTERENTER
EXITEXIT
ENTER
ENTER
Menu Operation Buttons
The menus are operated using buttons on this unit or remote control unit.
Button
Function
Displays the main menu.
●Press to clear the menu screen
when the menu is displayed.
Confirm the selected item on the main
menu.
●Press [ENTER] when the “Test
Pattern” item is selected to project
the test pattern on the screen. After
it is projected, test pattern changes
each time [ENTER] is pressed.
Press to return to the previous menu.
●Press to clear the menu screen
when the main menu screen is
displayed.
●Press to clear the test pattern when
a test pattern is displayed.
5/∞:Select menu items and adjust-
ment items.
2/3:Perform setting of the selected
adjustment item. (Setting is not
possible for some items)
The adjusted value will be re-
flected on the image immedi-
ately.
Remote Control UnitThis UnitRemote Control Unit
This Unit
Menu
Operation
Buttons
Menu
Operation
Buttons 
						

							24
LAMPTEMPSTAND BYOPERATE
MENUEXIT
ENTER
4
4
ON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
1, 6
1, 6 2, 3
2, 3
1Press the [MENU] button
● The main menu is displayed on the screen.
2Press [5/∞] to select a main menu item and [ENTER]
to confirm
●The “Information” menu does not have a setting menu (submenu).
3Press [5/∞] to select an adjustment item and [2/3]
to change the setting value
4After setting is completed, press [EXIT]
●Each time you press the button, the menu returns to the previous one.
5Repeat procedures 2 to 4 to set other items
6After setting is fully completed, press [MENU]
●The menu will disappear from the screen.
Adjustments and Settings Using Menus (continued)
Procedures for Menu Operation
●Press [ENTER] after selecting “Test pattern” on the “Image adjust”
menu. This will project the test pattern.Details of the currently selected menu
item will be displayed. Display of the menu item currently
selected becomes solid and icon of the
selected menu item is highlighted.
E.g.: “Mask” setting menu
E.g.: “Mask” setting menu E.g.: “Set up” menu
E.g.: “Menu Position” setting menu E.g.: “Image adjust” menu
Image adjust
Set up
Options
InformationGREENGREENBLUE RED
Color tempColor temp.
Test patternUSER2USER2USER1USER1D65D65
ENTER
GammaGammaNORMALNORMALACUSTCUSTOMOMB
Image adjust
Options
InformationMaskMaskOff5% 2.5%SourceSource50P 60PSet up
Menu PositionImage adjust
Options
InformationMenMenu PositionMaskMaskOff5% 2.5%SourceSource50P 60PSet up
Image adjust
Options
Information
Source50P 60PSet up
MenMenu PositionMaskMaskOffOff5% 2.5%Image adjust
Options
Information
SourceSource50P 60PSet up
Menu PositionMaskMaskOff5% 2.5% 
						

							25
¥¥¥ ¥ ¥ ¥ ¥ ¥
Item values shown in { } are factory settings.
1“Image adjust” Menu
To adjust images.
On the “Image adjust” menu, you can adjust the following items.
“Gamma”
Switches the gradation characteristics of the image. Select
your preference setting values according to the image to be
viewed.
Setting Values :“NORMAL”, “A”, “B”, “CUSTOM” {“NORMAL”}
“CUSTOM” : Use when setting Gamma with optional soft-
ware. The picture quality is same as “NOR-
MAL” for factory setting.
“Color temp.”
Adjusts the color temperature of the projected image.
Setting Values : “D65”, “USER1”, “USER2” {“D65”}
“RED” : -255 to 0 {0}
“GREEN” : -255 to 0 {0}
“BLUE” : -255 to 0 {0}
“Test pattern”
Use this to adjust focus, screen size or picture quality. There
are 10 types of test patterns. Press the [ENTER] or [TEST]
button to alter the test pattern to be projected.
2“Set up” Menu
The following items can be set at the “Set up” menu.
“Menu position”
Adjusts the display position of the menu screen.
Setting Values (menu display position):
{
}
“Mask”
Masks (hides) the outer area of the projected image.
Setting Values : “2.5%”, “5%”, “Off” {“Off”}
“Source”
Sets the image format for video image signals that are input to
this unit.
Ensure to align settings between this unit and the digital video
processor that is connected.
Setting Values : “60P”, “50P” {“60P”}
3“Options” Menu
The following items can be set at the “Options” menu.
“Menu display”
Adjusts the display duration of the menu screen.
Setting Values : “15 sec”, “On” {“15sec”}
“Flip H”
Reverses image to the left or right.
Setting Values : “On”, “Off” {“Off”}
“Flip V”
Inverses image upside down.
Setting Values : “On”, “Off” {“Off”}
“Picture shift”
When projecting images with black bands at the top and bottom
(cinema image), use this to move the image up or down while
retaining one of the black bands at the upper or lower end.
Setting Values : -30 to 30 {0}
“Sleep time”
Sets the lapse time before automatically switching the unit to
the standby mode when there is no signal input.
Setting Values : “15 min”, “30 min”, “60 min”, “Off” {“Off”}
“RS232C (bps)”
Sets the communication speed (signal transmission speed)
when communicating with a computer using the RS-232C
terminal. Ensure that this is same as the rate set at the
computer.
Setting Values : “9600”, “19200” {“19200”}
4“Information” Menu
“Lamp Time”
Displays the accumulated hours of usage of the light-source
lamp.
Menu Configuration 
						

							26
PRESET
MENUEXIT
ENTER
HIDE
ON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
2, 5
2, 5 3, 4
3, 4
Screen Masking
Images for which quality at the outer area has deteriorated can be projected by masking (hiding) the outer area of the projected
image.
1 Project image onto the screen
2Press the [MENU] button
●The main menu is displayed on the screen.
3Press [5/∞] to select “Set up”, followed by pressing
[ENTER]
●The “Set up” menu appears on the right side of the screen.
4Press [5/∞] to select “Mask”, followed by pressing
[2/3] to select the setting value
●Masks (hides) the outer area of the projected image.
5Press the [MENU] button to end
●The menu will disappear from the screen. E.g.: When “Mask” value is changed from “OFF” to “2.5%”Image for which the outer area has
deteriorated
Image adjust
Set up
Options
InformationGREENGREENBLUEBLUE
REDREDColor tempColor temp.
Test patter
est pattern
USER2USER2USER1USER1D65D65
ENTER
GammaGammaNORMALNORMALACUSTCUSTOMOMB
Image adjust
Options
InformationMaskMaskOffOff5% 2.5%SourceSource50P50P60P60PSet up
MenMenu Position
Image adjust
Options
Information
Source50P50P60P60PSet up
MenMenu Pu PositionositionMaskMaskOffOff5%5%2.5%2.5% 
						

							27
PRESET
MENUEXIT
ENTER
HIDE
ON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
2, 5
2, 5 3, 4
3, 4
Image adjust
Set up
Options
InformationGREENGREENBLUEBLUE
REDREDColor tempColor temp.
Test patter
est pattern
USER2USER2USER1USER1D65D65
ENTER
GammaGammaNORMALNORMALACUSTCUSTOMOMB
Image adjust
Set up
InformationPicture ShiftPicture ShiftSleep timeSleep time
Flip Flip VOnOnOffOff
15minOff30min60min960096001920019200
OnOn0OffOffFlip HFlip H
RS232C(bps)RS232C(bps)
Options
MenMenu displau display15sec15secOnOn
Image adjust
Set up
InformationSleep timeSleep time
Flip VOnOnOffOff
15min15minOff30min30min60min60min960096001920019200
OnOnOffOffFlip H
RS232C(bps)
RS232C(bps)
Options
MenMenu display15sec15secOnOn
Picture Shift3030
Picture Shift Setting
When projecting images with black bands at the top and bottom (cinema image), use this to move the image up or down while
retaining one of the black bands at the upper or lower end.
1 Project image onto the screen
2Press the [MENU] button
●The main menu is displayed on the screen.
3Press [5/∞] to select “Options”, followed by press-
ing [ENTER]
●The “Options” menu appears on the right side of the screen.
4Press [5/∞] to select “Picture Shift”, followed by
pressing [2/3] to move the image upwards or down-
wards
●Set value in the positive (+) direction to move the image upwards and
negative (-) direction to move downwards.
5Press the [MENU] button to end
●The menu will disappear from the screen. E.g.: When “Picture Shift” value is changed from “0” to “30”2.35:1 Cinema Image 
						

							28
Light-source Lamp and Lamp Usage Time
The light-source lamp has a service life. The life of lamps used for this unit is about 2000 hours.
●The lamp life of 2000 hours is merely the average life span of lamps and we do not provide any guarantee for this figure. The
lamp life may not reach 2000 hours depending on the operating conditions.
When the light-source lamp approaches the end of its service life, deterioration progresses rapidly. Get ready or replace with a
new lamp (lamp unit) when the accumulated lamp usage time exceeds 1900 hours. Depending on the operating conditions, the
lamp may have to be exchanged earlier. If the image is dark or color tone abnormal, replace the lamp as soon as possible. You
can also check the accumulated hours of usage. Please refer to the “Lamp Time” item of the “Information” menu. (☞ Pages 22,
25)
When lamp usage time exceeds 2000 hours
The [LAMP] indicator starts to blink.
The “Warning” and “Lamp replacement” messages will be displayed
on the projected screen with the “Warning” word blinking.
●Press the [EXIT] button to clear the display.
However, the same “Warning” and “Lamp replacement” messages
will be displayed again after 1 hour.
When the unit is switched to the standby mode or turned off after
the lamp usage time exceeds 2000 hours, it cannot be switched
back to the projection mode again. In this case, replace with a
new lamp (lamp unit) and reset the lamp time (
☞ Page 30).
When the lamp usage time exceeds 2010 hours
The 
unit quits the projection mode (operating mode) and switches
into the cool down mode.
●The [LAMP] and [OPERATE] indicators will start blinking.
The projection mode (operating mode) cannot be restored until a
new lamp (lamp unit) is replaced and the lamp time reset
(☞ Page 30).
When the lamp usage time exceeds 1000 hours
A message indicating “1000 h” will be displayed on the screen.
●Press the [EXIT] button to clear the display.
When the lamp usage time exceeds 1900 hours
The [LAMP] indicator lights up.
When starting projection after lamp usage time exceeds 1900
hours
The “Lamp replacement” message will be displayed on the screen.
●Press the [EXIT] button to clear the display.
Procedure for Lamp Replacement
1Loosen the screws and remove the lamp
cover
●Loosen the 2 screws with a ª screwdriver. Please consult your authorized dealer when purchasing a new lamp unit.
Replacement Lamp (Lamp Unit) Part No.: BHL 5006-S
Replacing the Lamp
About Lamp Replacement
●If this unit is installed in a constricted place, attempting to replace the lamp in that place may cause injury. Move this unit
to a place large enough to perform the work.
●Use only genuine replacement parts for the lamp unit. Otherwise, malfunction may occur. Also, never attempt to re-use an
old lamp unit. This may cause marked performance deterioration or lamp blowout, thus leading to 
unit malfunction.
Broken pieces of the lamp outside this unit may also cause injuries during lamp unit exchange.
●Do not replace the lamp immediately after this unit has been used. The temperature of the lamp unit is still high and this
may cause a burn. Allow a cooling period of 1 hour or more before replacement.
●Before replacing the lamp unit, pull out the power plug from the outlet while the [STAND BY] indicator is still on. Replacing
a lamp with the plug connected to the outlet may cause injuries or electric shocks. 
						

							29
Handle
Lamp Unit
2Loosen the screws on the lamp unit and
lift up the handle
●Loosen the 2 screws with a ª screwdriver.
3Pull out the lamp unit
4Insert the new lamp unit until it is fully in
5Tighten the screws of the lamp unit and
close the handle
●Fasten the 2 screws with a ª screwdriver.
6Attach the lamp cover and fasten the
screws
●Fasten the 2 screws with a ª screwdriver.
Caution
Do not touch the glass surface of the lamp directly with
your hand or stain it. Touching it with a bare hand may
dirty the surface, hence shortening the lamp life, causing
marked performance deterioration such as darkened
screens, lamp blowout as well as malfunction.
Note
When fitting the lamp cover, insert the left end (with 2 claws)
of the lamp cover into the unit, followed by ensuring that
the protruding part on the reverse side of the lamp cover
fits snugly into the hole of the unit.
As this protrusion acts as a switch, misfitting may lead to
failure in turning on the power. 
						

							30
EXIT
PRESET
HIDE
ON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
[PRESET] [HIDE]
[5] [EXIT]
Resetting Lamp Time
After installing a new lamp (lamp unit), reset the lamp time. The lamp time counter will be reset and a new count will start.
If display of the accumulated lamp time has reached 2000 hours, this unit will not work (lamp does not light up) unless the lamp
time is reset.
1Insert plug into the power outlet
●The [STAND BY] indicator on the unit lights up when the main power is
turned on.
2Press the [EXIT], [HIDE] and [PRESET] buttons se-
quentially, then press [5] for 2 seconds or more
●The [STAND BY] and [OPERATE] indicators will alternately blink for a
duration of 3 seconds each. After blinking stops, lamp time resets and
the unit returns to the standby mode ([STAND BY] indicator lights up).
Replacing the Lamp (continued)
Press as per normal
Press for 2 seconds or more
To ensure the lamp time has been reset
The lamp time can be checked via the “Lamp Time” item under
“Information” of the main menu. (☞ Pages 22, 25)
Reset the lamp time only when you have replaced the lamp.
Never reset it when the lamp is still in use.
Otherwise, the approximate standard for gauging replacement time may
be inaccurate, lamp performance may deteriorate and lamp blowout may
occur.
Caution During Reset Work