JVC Projector Dla Hd2ku Instructions Manual

11
Indicator Display on the Control Panel
LAMP TEMPSTAND BYOPERATE
LAMP TEMPSTAND BYOPERATELAMP TEMPSTAND BYOPERATE
LAMP TEMPSTAND BYOPERATELAMP TEMPSTAND BYOPERATELAMP TEMPSTAND BYOPERATE
LAMP TEMPSTAND BYOPERATELAMP TEMPSTAND BYOPERATE
LAMP TEMPSTAND BYOPERATE
LAMP TEMPSTAND BYOPERATELAMP TEMPSTAND BYOPERATELAMP TEMPSTAND BYOPERATE
In addition to the standby mode, operate mode and cool down mode*, this unit also displays other operational states using
different combination of indicators.
●Please refer...

12
1Remote Control’s Signal Transmitter
(☞ Page 17)
2[OPERATE ON] Button
When this unit is in the standby mode, pressing the but-
ton for more than 1 second will turn this unit on and cause
the [OPERATE] indicator to light up. (☞ Page 20)
3[LIGHT] Button
Lights up illumination (light) of the remote control buttons
for about 10 seconds.
4[FOCUS] Button
Use this button to adjust focus of the projected image.
Press the button to switch to the image mode for focus
adjustment. Adjust focus using the focus...

13
Precautions for Using Batteries
Loading Batteries into the Remote Control
1Open the back cover
Press the back cover slightly and slide it in the direction of
the arrow.
2Load the batteries
Insert the 2 (AAA) batteries supplied according to the 9,
( marks. To prevent short circuit, be sure to insert the (
(minus) end of the battery first.
3Close the back cover
Slide in the direction of the arrow to close the back cover. Load batteries into the remote control. If the remote control starts to function...

14
Installing the Projector
Precautions for Installation
Please read the following carefully when installing this unit.
Minimum Space Required
Adjusting the Inclination
Vertical angle adjustment rangeAdjusting the vertical angle
While pushing the foot lever upward,
raise this unit to extend the front foot
(maximum extension is about 31
mm). To retract the foot, push the
level upward and lower the unit
slowly. This unit will be fixed at the
position where you released the foot
lever.
Fine-tuning the...

15
Projector and Screen Installation

When viewed from the left (or right) 
When viewed from the top (or bottom)
The optimum image can be obtained when the center of this unit lens and \
the screen are placed perpendicular to each other.
Take note of the projection angle when placing them. Failing to do so ma\
y give rise to trapezoidal distortion of the projected
image.
●This unit does not come with a function to correct trapezoidal distortio\
n.
Mounting  this Unit
When mounting of this unit is...

16
Projection Screen Size (DiagonalLength) of Aspect Ratio 16:9
40 (Approx. 101.6 cm)
50 (Approx. 127.0 cm)
60 (Approx. 152.4 cm)
70 (Approx. 177.8 cm)
80 (Approx. 203.2 cm)
90 (Approx. 228.6 cm)
100 (Approx. 254.0 cm)
110 (Approx. 279.4 cm)
120 (Approx. 304.8 cm)
130 (Approx. 330.2 cm)
140 (Approx. 355.6 cm)
150 (Approx. 381.0 cm)
160 (Approx. 406.4 cm)
170 (Approx. 431.8 cm)
180 (Approx. 457.2 cm)
190 (Approx. 482.6 cm)
200 (Approx. 508.0 cm) Approximate Projecting Distance
W (Wide) - T (Tele)
(Approx....

17
OPER AT EO
NEN TE RO
FFFO CU ST
E
S T
M EN
U E
XIT
P R ESE TH
ID
ELIG
HT
20˚20˚ 30˚
30˚
A
B
Effective Range of Remote Control Unit
The operable distance of the remote control unit is about 7 m for direct\
 reception. The remote control unit can be used by havi ng
the transmission signal reflected off a screen.
● If the fluorescent lamp is lit, the remote control unit might not functi\
on properly.
Screen
Remote Control Unit Remote Sensor (Rear)
This unit

 When reflecting off a screen
Ensure that...

18
RS-232C
CONTROL
SERVICE SYNC
OUT
DVI  OUTPUT
DVI
VIDEO IN
CONTROL
RS-232CSERVICE SYNC
OUT
Connecting to Various Devices
Connecting to Devices
Before connection, be sure to turn off both the projector and the device to be connected.

Connecting to digital video processors
●Read the manual that is supplied with the digital video processor thoroughly.
●The signal may attenuate and the image may become unstable depending on the DVI cable. Use the high quality DVI
cable below 5 m. When using DVI cable...

19
2
1
1Connect the supplied power cord to the power in-
put terminal of this unit
2Insert the main plug of the supplied power cord
into the wall outlet
Connecting the Power Cord (supplied)
After all devices have been connected, connect the supplied power cord.
Power Cord (supplied)
(e.g.)
Lens Cap
When using this unit, remove the lens cap
● Be sure to fit the lens cap on when this unit is not in use to keep out
dirt.
● Do not project with the lens cap attached. The lens cap may be de-
formed by heat or...

20
LAMP TEMPSTAND BYOPERATEON
ENTER
OFF
FOCUSTEST
MENUEXIT
PRESETHIDE
LIGHT
OPERATE
LAMPTEMP
STAND BYOPERATE
MENUEXIT
ENTER
1-2
1-2
LAMP TEMP STAND BYOPERATE
Indicators on this unit
2
3
If setting for this unit is not completed, please refer to “Adjustmen\
ts and Settings Using Menus”( ☞ Page 22) upon turning on the
power and perform the required setting accordingly. Once the basic setti\
ng is completed, this unit can be used by simply
performing the following operation procedures.
Basic Operation...