JVC Dt V24l3d Instructions

							INSTRUCTIONS
DT-V24L3D
DT-V20L3D
MULTI FORMAT LCD MONITORTable of Contents
Safety Precautions .............................................. 2
 IMPORTANT SAFEGUARDS ........................... 2
Installation ............................................................ 4
Daily Operations / Connections ......................... 6
 Front panel ....................................................... 6
 Rear panel ........................................................ 8
 Available signals ............................................... 9
Menu Configuration—MAIN MENU .................. 10
Menu Configuration—SET-UP MENU ............... 14
External Control ................................................. 16
 About the external control .............................. 16
 Using the MAKE/TRIGGER system ............... 17
 Using the serial communication ..................... 18
Troubleshooting ................................................. 19
 Self-check program ........................................ 20
Maintenance ....................................................... 20
Specifications .................................................... 21
 General ........................................................... 21
 Input/output terminals ..................................... 21
 Dimensions ..................................................... 22
The illustration of the monitor is of DT-V24L3D.
CAUTION:  To reduce the risk of electric shock. Do 
not remove cover (or back). No user 
serviceable parts inside. Refer servicing 
to qualied service personnel. 
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
The lightning ash with arrowhead 
symbol, within an equilateral triangle is 
intended to alert the user to the presence 
of uninsulated “dangerous voltage” 
within the product’s enclosure that may 
be of sufcient magnitude to constitute a 
risk of electric shock to persons.  
The exclamation point within an 
equilateral triangle is intended to alert 
the user to the presence of important 
operating and maintenance (servicing) 
instructions in the literature 
accompanying the appliance.  
CAUTION
LCT2447-002A-H
DT-V24_20L3D_EN.indd   1DT-V24_20L3D_EN.indd   108.9.9   2:47:48 PM08.9.9   2:47:48 PM
 
						

							2
  Do not install this product in the following places:
– in a damp or dusty room
– where the product is exposed to soot or 
steam, such as near the cooking counter or a 
humidifier 
– near heat sources
– where condensation easily occurs, such as 
near the window
  Do not place this product on an unstable cart, 
stand, or table. The product may fall, causing 
serious injury to a child or adult, and serious 
damage to the product.
 The product should be mounted according to the 
manufacturer’s instructions, and should use a 
mount recommended by the manufacturer.
  Do not use this product near water.
  Be sure to install the product in the place where 
proper temperature and humidity are kept (☞ 
“Operating conditions” on page 21).
 This product becomes hot during its use. Take 
enough care when handling the product.
Safety Precautions
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO 
RAIN OR MOISTURE. NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE 
PLACED ON THE APPARATUS.
 IMPORTANT SAFEGUARDS
Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure 
your personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRIC SHOCK OR FIRE. In order 
not to defeat the safeguards incorporated into this product, observe the following basic rules for its installation, 
use, and service. Please read these “IMPORTANT SAFEGUARDS” carefully before use.
  All the safety and operating instructions should be read before the product is operated.
  The safety and operating instructions should be retained for future reference.
  All warnings on the product and in the operating instructions should be adhered to.
  All operating instructions should be followed.
Fuse
For United Kingdom: 
AC 220 – 240 V For European and 
Asian countries: 
AC 220 – 240 V For U.S.A. and Canada: 
AC 120 V
Under the following conditions,
1.  Turn off the power.
2.  Unplug this product from the wall outlet.
3.  Refer service to qualified service personnel.
a)  When the product emits smoke or unusual 
smell.
b)  When the product exhibits a distinct change in 
performance —for example, no picture or no 
sound.
c)  If liquid has been spilled, or objects have fallen 
on the product.
d)  If the product has been exposed to rain or water.
e)  If the product has been dropped or damaged in 
any way.
f)  When the power supply cord or plug is 
damaged.
  The AC power supply is controlled by turning on/
off the POWER switch on the rear panel. If the 
product is installed in a place where you cannot 
easily turn on/off the POWER switch, control the 
AC power supply by plugging/unplugging the 
power cord into/from the AC outlet. In this case, 
install the product as close to the AC outlet as 
possible, and leave enough space for plugging/
unplugging the power cord. If the product is 
installed in a place where you cannot easily 
plug/unplug the power cord, equip an easily 
accessible device to the wiring of the building for 
turning on/off the power.
  When the product is left unattended and unused 
for a long period of time, unplug it from the wall 
outlet and disconnect the cable system.
  Do not overload wall outlets, extension cords, or 
convenience receptacles on other equipment as 
this can result in a risk of fire or electric shock.
  Use only the accessory cord designed for this 
product to prevent shock.
  Slots and openings in the cabinet are provided 
for ventilation. These ensure reliable operation 
of the product and protect it from overheating. 
These openings must not be blocked or covered.
  Never push objects of any kind into this product 
through openings as they may touch dangerous 
voltage points or short-circuit the parts, which 
could result in a fire or electric shock.
  Never spill liquid of any kind on the product.
  Never place anything on the product. (Placing 
liquids, naked flames, cloths, paper, etc. on the 
product may cause a fire.)
  Do not apply any strong shock to the LCD panel. 
(Do not hit any object against it or push it with a 
sharp-pointed tool.)
  Do not put heavy objects on the product.
  Do not step on or hang on the product.
Do not use the product for a long time if the sound 
is distorted. 
POWER CONNECTION
The power supply voltage rating of this product is AC 120 V (For U.S.A. and Canada) and AC 220 – 240 V (For 
European countries, Asian countries, and United Kingdom).
The power cord attached conforms to the following power supply voltage and countries. Use only the power 
cord designated to ensure safety and EMC regulations of each country.
  Not all types of power cords are supplied to this product.
This plug will fit only into a grounded power outlet. If you are unable to insert the plug into the outlet, contact 
your electrician to install the proper outlet. Do not defeat the safety purpose of the grounded plug.
  This product should be operated only with the type of power source indicated on the label. If you are not 
sure of the type of power supply of your home, consult your product dealer or local electric power company.
Warning:
  Do not use the same power cord for AC 120 V as for AC 220 – 240 V. Doing so may cause malfunction, 
electric shock or fire.
Note for United Kingdom power cord only
The plug of United Kingdom power cord has a built-in fuse. When replacing the fuse, be sure to use only a 
correctly rated approved type, re-fit the fuse cover. (Consult your dealer or qualified personnel.)
How to replace the fuse
Open the fuse compartment with the blade screwdriver, and replace the fuse.
  Before connecting other products such as VCR’s and personal computers, you should turn off the power of 
this product for protection against electric shock.
  Do not use attachments not recommended by the manufacturer as they may be hazardous.
 When replacement parts are required, be sure the service technician has used replacement parts 
specified by the manufacturer or equivalents. Unauthorized substitutions may result in fire, electric shock, or 
other hazards.
 Upon completion of any service or repairs to this product, ask the service technician to perform safety 
checks to determine that the product is in proper operating condition.Do not attempt to service this product yourself, as 
opening or removing covers may expose you to 
dangerous voltages and other hazards. Refer all 
service to qualified service personnel.
Caution for use of the product in the high temperature
Do not use the product in places of high temperature; otherwise, parts of this product or the LCD panel may 
be damaged. This product is equipped with a temperature sensor to give warning if the temperature becomes 
too high. If the temperature exceeds the range of normal use, “TEMP. OVER” is displayed, and the power is 
turned off automatically if the temperature becomes any higher. In this case, move the product to a place of 
low temperature to let it cool down.
Warning: This is a class A product. In a domestic environment this product may cause radio interference in 
which case the user may be required to take adequate measures.
DT-V24_20L3D_EN.indd   2DT-V24_20L3D_EN.indd   208.5.27   5:14:45 PM08.5.27   5:14:45 PM
 
						

							Dear Customer,
This apparatus is in conformance with the valid 
European directives and standards regarding 
electromagnetic compatibility and electrical safety. 
European representative of Victor Company of Japan, 
Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
Information for Users on Disposal of Old 
Equipment
[European Union]
This symbol indicates that the 
electrical and electronic equipment 
should not be disposed as general 
household waste at its end-of-
life. Instead, the product should 
be handed over to the applicable 
collection point for the recycling of 
electrical and electronic equipment 
for proper treatment, recovery and 
recycling in accordance with your 
national legislation.
By disposing of this product 
correctly, you will help to conserve 
natural resources and will help 
prevent potential negative effects 
on the environment and human 
health which could otherwise 
be caused by inappropriate waste handling of this 
product. For more information about collection point 
and recycling of this product, please contact your 
local municipal office, your household waste disposal 
service or the shop where you purchased the product.
Penalties may be applicable for incorrect disposal of 
this waste, in accordance with national legislation.
(Business users)
If you wish to dispose of this product, please visit our 
web page www.jvc-europe.com to obtain information 
about the take-back of the product.
[Other Countries outside the European Union]
If you wish to dispose of this product, please do so in 
accordance with applicable national legislation or other 
rules in your country for the treatment of old electrical 
and electronic equipment.Attention:
This symbol is 
only valid in the 
European Union.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS 
APPARATUS TO RAIN OR MOISTURE.
WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET 
WITH A PROTECTIVE EARTHING CONNECTION.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. 
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
IMPORTANT SAFETY INSTRUCTIONS
1)  Read these instructions.
2)  Keep these instructions.
3)  Heed all warnings.
4)  Follow all instructions.
5)  Do not use this apparatus near water.
6)  Clean only with dry cloth.
7)  Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8)  Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including 
amplifiers) that produce heat.
9)  Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one 
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the 
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for 
replacement of the obsolete outlet.
10)  Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point 
where they exit from the apparatus.
11)  Only use attachments/accessories specified by the manufacturer.
12)  Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or 
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13)  Unplug this apparatus during lightning storms or when unused for long periods of time.
14)  Refer all servicing to qualified service personnel. Servicing is required when the 
apparatus has been damaged in any way, such as power-supply cord or plug is 
damaged, liquid has been spilled or objects have fallen into the apparatus, the 
apparatus has been exposed to rain or moisture, does not operate normally, or has 
been dropped.
15)  Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be 
placed on the apparatus.
16)  Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
17)  When discarding batteries, environmental problems must be considered and the local rules or laws governing the 
disposal of these batteries must be followed strictly.
3
European Union only
FCC NOTICE
CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the 
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 
harmful interference when the equipment is operated in a commercial environment. This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the user will be required to correct the interference at 
his own expense.
IMPORTANT RECYCLING INFORMATION
This product has a fluorescent lamp that contains mercury. Disposal of these materials 
may be regulated in your community due to environmental considerations. For disposal 
or recycling information, please contact your local authorities or for USA, the Electronic 
Industries Alliance: http://www.eiae.org
U.S.A. only
EMC Supplement
This equipment is in conformity with the provisions 
and protection requirements of the corresponding 
European Directives. This equipment is designed for 
professional video appliances and can be used in the 
following environments:
  Controlled EMC environment (for example purpose 
built broadcasting or recording studio), and rural 
outdoors environment (far away from railways, 
transmitters, overhead power lines, etc.)
In order to keep the best performance and ensure 
electromagnetic compatibility, we recommend to use 
cables not exceeding the following length:
Cable   Length
Power cord    2.0 m
(attached cable (H05VV-F 3 x 0.75 mm
2))
Video signal cable  2.0 m
(coaxial cable)
Audio signal cable (shielded cable)  1.5 m
DVI cable (shielded cable)  1.5 m
RS-232C cable (shielded cable)  2.0 m
(A straight cable with a D-sub 9-pin connector)
RS-485 cable (twist pair cable)  2.0 m
(A straight LAN cable)
REMOTE cable (twist pair cable)  2.0 m
(A straight LAN cable)
The inrush current of this apparatus is 6 ampere.
CAUTION
In case where the strong electromagnetic waves or 
magnetism are near the audio cable or the signal 
cable, the sound or the picture will contain noise. In 
such cases, please keep the cable away from the 
sources of the disturbance.
DT-V24_20L3D_EN.indd   3DT-V24_20L3D_EN.indd   308.5.27   5:14:48 PM08.5.27   5:14:48 PM
 
						

							4Installation
CAUTION
  Do not rest your arm on the monitor or lean against the monitor.
  Do not touch the LCD panel when installing the monitor.
  Be sure to install the monitor securely to prevent the monitor from falling over, which may cause damage to the monitor 
or injury.
You can place the monitor in the following two ways when using it on the supplied stand.
You can tilt the monitor from about 6° upward to 
about 6° downward.
  When the monitor is not tilted (0°), the guidelines 
align as illustrated below.
The illustration of the monitor is of DT-V24L3D.
  You can select the stand height—higher position 
or lower position (☞ “To adjust the stand height” on 
page 5).
CAUTION
  Be careful not to pinch your fingers in the gap between 
the monitor and the stand.
  When the stand plate is attached to the lower 
position of the stand body, you cannot tilt the monitor 
downward.
When the stand plate is attached to the higher 
position of the stand body (☞ “To adjust the stand 
height” on page 5), you can place the monitor as 
illustrated below.
1 Remove the screws on the left and right sides of 
the stand (see the illustration below), then lift the 
stand up by about 148°.
2 Attach the removed screws and place the monitor 
as illustrated below.
The illustrations of the monitor are of DT-V24L3D.
  To place the monitor as illustrated on the left again, 
remove the screws on the left and right sides of the 
stand, return the monitor angle to 0°, then reattach 
the removed screws.
CAUTION
  When lifting up the stand...
–  lay the monitor on a cloth with the LCD panel 
facing down to prevent the LCD panel from being 
damaged.
–  be careful not to pinch your fingers in the moving 
parts.
  Make sure of lifting the stand up until it stops (about 
148°); otherwise the monitor may fall over.
  Place the monitor on a mat to avoid scratching the 
table surface.
  Do not lift up the stand when the stand plate is 
attached to the lower position of the stand body.
To detach the stand
CAUTION
Lay the monitor on a cloth with the LCD panel facing down to prevent the LCD panel from being damaged.
About 6°
About 6°Screw holes for stand 
attachment
Screw holes for 
stand attachment
Stand bodyGuidesGuide holes Attachment screws
Monitor
To install the stand
When attaching the stand to the monitor, insert the guides of the stand into the guide holes on the monitor to 
place the stand in the correct position. Then fix the stand firmly with the attachment screws.
0°Screw 
(silver)
Stand plate About 
148°The illustration of the monitor is of DT-V24L3D.
Stand Monitor
Stand body
Monitor
The illustration of the monitor 
is of DT-V24L3D.
Guidelines
DT-V24_20L3D_EN.indd   4DT-V24_20L3D_EN.indd   408.5.27   5:14:51 PM08.5.27   5:14:51 PM
 
						

							5
To adjust the stand heightTo change the stand height, detach the stand from the monitor (☞ “To detach the stand” on page 4). Then, 
change the position of the stand plate according to the stand height you want by choosing the screw holes to use.
Screw holes for higher position Screw holes for lower position
Stand plate
Stand plate
Stand body
Stand body
 
To prevent an accidental fall
Fix the monitor to a wall by using strings.
Fixing the monitor
Attach the hook (not provided) to the VESA mounting holes on the rear panel (use the two holes on the upper 
side) using M4 x 10 mm screws (not provided). Bind the hooks on the rear panel of the monitor to a wall or a pillar 
using durable string.
Hook and screw (M4 x 10 mm) 
(not provided)
Hook (not provided) VESA mounting holes
The illustration of the monitor is of DT-V24L3D.
DT-V24_20L3D_EN.indd   5DT-V24_20L3D_EN.indd   508.5.27   5:14:52 PM08.5.27   5:14:52 PM
 
						

							6Daily Operations / Connections 
7 Front panel
p SAFETY MARKER button/lamp
Displays/hides the safety marker.
  Adjust the area of the safety marker in “MARKER” 
of the MAIN MENU (☞ page 11).
  This function does not work when displaying the 
picture in the 1:1 mode.
  This function does not work when “SAFETY 
MARKER” or “R-SAFETY MARKER” is set to 
“OFF” in “MARKER.”
q SCREENS CHECK button/lamp
Displays only the selected element (R, G, or B) of 
the video signal.
  Each time you press this button, the screen 
changes in the following order.
w ASPECT button/lamp
Changes the aspect ratio of the picture from 4:3 
to 16:9 when the picture of 16:9 aspect ratio is 
squeezed into 4:3 format signal.
  To return to 4:3, press the button again.
  This function does not work when displaying the 
picture in the 1:1 mode.
e WAVE FORM button/lamp
Displays/hides the indication of the wave form 
monitor.
  Adjust the settings of the wave form monitor in 
“WAVE FORM SETTING” of the MAIN MENU (☞ 
page 13).r T.C. (time code) button/lamp
Activates/deactivates the display of the time data 
(time code) contained in the SDI signal.
(☞ 
“On the Information Display” on page 7)
t INPUT SELECT buttons/lamps
Selects an input.
SDI 1: E. AUDIO HD/SD SDI (IN 1) terminal
SDI 2: E. AUDIO HD/SD SDI (IN 2) terminal
DVI: DVI-D (HDCP) terminal
COMPO./RGB: COMPO./RGB. terminal
VIDEO 1: VIDEO (INPUT 1) terminal
VIDEO 2: VIDEO (INPUT 2) terminal
  The lamp for the selected input lights.
y Power lamp
Unlit: The monitor is completely off (the Power 
switch on the rear panel is turned off).
Lights in Green: The monitor is on.
Lights in orange: The monitor is off (on standby).
Flashes in orange: The monitor is in the P. SAVE 
(power save) mode (☞ “NO SYNC ACTION” in 
“SYNC FUNCTION” on page 13).
u 
 button
Turns on and off (on standby) the monitor.
  The power switch is equipped on the rear panel of 
the monitor (☞ 1 on page 8). Tally lamp
This lamp is controlled by the tally function 
of the MAKE/TRIGGER terminal (☞ “ TALLY 
SELECT” in “FUNCTION SETTING” on page 
14 and “External Control” on page 16).  “NO EFFECT” is displayed when you press a button which is not available for the current input or signal format (the lamp lights even when the function does not 
actually work). 
  The items controlled by the MAKE system cannot be controlled by the buttons on the front panel (“REMOTE ON” is displayed and the lamps do not light).
5  /   /   /   buttons
When a menu screen is displayed
Selects or adjusts menu items. (☞ 
“Menu 
Operations” on page 7)
When no menu screen is displayed
Selects the audio channels of EMBEDDED AUDIO 
signals. (☞ “Audio Channel Selection” on page 7)
 
Pressing   button while holding   button displays the 
SET-UP MENU. (☞ “Menu Operations” on page 7)
6 MENU buttonActivates/deactivates the display of the MAIN MENU.(☞ “Menu Operations” on page 7)
7 COLOR OFF button/lamp
Displays only the luminance signal.
  This function does not work for RGB input signals.
8 1:1 button/lamp
Displays the picture in the original resolution of the 
input signal.
  The aspect ratio of the picture may change 
depending on the input signal.
9 AREA MARKER button/lamp
Displays/hides the area marker.
  Select the style of the area marker in “MARKER” 
of the MAIN MENU (☞ page 11).
  This function works only when displaying the 
picture in 16:9 aspect ratio.
  This function does not work when “AREA 
MARKER” or “R-AREA MARKER” is set to “OFF” 
in “MARKER.”
The illustration of the monitor is of DT-V24L3D.
1 Speakers (stereo)
The speakers emit the same audio signal emitted 
from the AUDIO ASSIGN (MONITOR OUT) 
terminals.
(☞ “ 8 AUDIO ASSIGN (MONITOR OUT) 
terminals” on page 8)
2 VOLUME adjustment knob
Adjusts the volume.
3 Picture adjustment knob
PHASE: Adjusts the picture hue.
CHROMA: Adjusts the picture color density.
BRIGHT: Adjusts the picture brightness.
CONTRAST: Adjusts the picture contrast.
4 MUTING button
Turns off the sound when no menu screen is 
displayed.
  To cancel the function, press the button again or 
turn the VOLUME adjustment knob.
  Muting function is also canceled when 
“BALANCE” of “AUDIO SETTING” in the MAIN 
MENU is changed (☞ page 12).
RGB (Normal screen) Red screen
Green screen Blue screen
DT-V24_20L3D_EN.indd   6DT-V24_20L3D_EN.indd   608.5.27   5:14:53 PM08.5.27   5:14:53 PM
 
						

							7
If you press the INPUT SELECT button of the 
current input, the status of the input signal 
and setting of muting are displayed for about 3 
seconds.
  Make the setting to display/hide the status in 
“STATUS DISPLAY” of the “INFORMATION” (☞ 
page 15).
  When “STATUS DISPLAY” is set to “AUTO” or 
“ON,” the status below is also displayed in the 
following cases:
– When you change the input
– When the signal condition of the current input 
changes
– When you turn on the monitor
  When “STATUS DISPLAY” is set to “ON,” the 
signal format will remain displayed 3 seconds 
after the status is displayed.
1 Signal format
  For the contents displayed, see “On the 
signal format” below and “Available signals” 
on page 9.
2 Signal format of DVI input or setting of 
“COMPO./RGB SEL.”
☞ “DVI INPUT SEL.” or “COMPO./RGB SEL.” 
on page 10
3 Displayed when “SYNC INPUT SEL.” is set 
to “EXT.” (external synchronization)
☞ “ SYNC FUNCTION” on page 13
4 Setting of “MUTING”
  Displayed only when muting is activated.
☞ “ 4 MUTING button” on page 6The monitor displays the information below.
  Make the setting to display/hide each 
information using the MENU with the exception 
of 5, controlled with a button.
  Select the position of the information display (☞ 
“POSITION” in “INFORMATION” on page 15).
1 Audio level meter
 
Not displayed when “LEVEL METER ch” is set 
to “OFF.” (☞ “AUDIO SETTING” on page 12)
2 Signal format
  Displayed when “STATUS DISPLAY” is set to 
“ON.” (☞ “INFORMATION” on page 15)
  For the contents displayed, see “On the 
signal format” below and “Available signals” 
on page 9.
3 
Source name assigned in “CHARACTER SET.”  Displayed when “SOURCE ID” is set to “ON.”
  Displayed in large letters when “STATUS 
DISPLAY” is set to “OFF” or “AUTO.”
☞ “INFORMATION” on page 15
4 CRC error indication
 Displayed when “
CRC ERROR” is set to “ON.” (☞ “INFORMATION” on page 15)  A red square is displayed when an error 
occurs.
5 Time code
  When the input signal includes no time code, 
“TC – –:– –:– –:– –” is displayed.
☞ “ r T.C. (time code) button/lamp” on page 6
  When any information of 1, 2, 3, or 4 
above is displayed while signals come in from 
equipment other than a computer, the picture is 
displayed without overlapping the information 
display area.
 However, the information display will overlap 
with the picture when...
– displaying the picture with higher resolution 
than the resolution of the panel in 1:1 mode.
– “SD4:3 LARGE” setting is “ON.” 
(☞ “FUNCTION SETTING” on page 14).
Select audio channels emitted from the speakers 
(L/R) and the AUDIO ASSIGN (MONITOR OUT) 
(OUT1(L)/OUT2(R)) terminals, when EMBEDDED 
AUDIO signals come in to the E. AUDIO HD/SD 
SDI terminal (IN1 or IN2) and SDI input (1 or 2) is 
selected.
  You have to choose a group of selectable audio 
channels before the channel selection (☞ 
“E.AUDIO GROUP” in “AUDIO SETTING” on 
page 12).
1 Press  or   button when a menu 
is not displayed.
The screen for audio channel selection is 
displayed.
  The screen for audio channel selection 
automatically disappears in about 30 
seconds after the previous operation.
2 Press     buttons to select the left 
(L ch) or right (R ch).
3 Press     buttons to select an 
audio channel.
  Each time you press the button, the audio 
channel changes according to the settings of 
“E.AUDIO GROUP” (☞ “NOTE” on page 12).
4 Press MENU button.The screen for audio channel selection 
disappears.
  The setting is memorized for each input (SDI 1 
and SDI 2).
1 Display the menu.To display the MAIN MENU\ Press MENU button.
To display the SET-UP MENU
\ Press  button while holding   button.
2 Press     buttons to select an item, 
then press   button.
  For some items, adjustments will be made by 
pressing  .
3 Press     buttons to select an item, 
then press     buttons to make 
adjustments.
4 Press MENU button to return to the 
previous menu.
  Pressing the button again finishes the menu 
operation.
On the Status Display Audio Channel Selection
MAIN MENU
SET-UP MENU Selected item
Selected item Operation guide
Selected item
Operation guide
Ex.: When “MARKER” in the MAIN 
MENU is selected
Menu Operations
Audio channel selection screen
On the Information Display
On the signal formatThe following messages appear depending on the 
type of input signals and their conditions.
When a DVI-D signal protected 
with HDCP is input“*” (at the end of 
the indication)
When no video signal comes in “NO SYNC”
When a noncompliant video 
signal comes in“Out of range”
When “COLOR SYSTEM” (☞ 
“FUNCTION SETTING” on 
page 14) is set to “AUTO” and 
the noncompliant composite 
video signals come in“OTHERS”
DT-V24_20L3D_EN.indd   7DT-V24_20L3D_EN.indd   708.5.27   5:14:55 PM08.5.27   5:14:55 PM
 
						

							8
7 Rear panel
Daily Operations / Connections (cont.)
The illustration of the monitor is of DT-V24L3D.
1 Power switch
Turns the power on or off.
  You need to press 
 button (☞ u on page 
6) to use the monitor after turning on the power 
switch.
2 AC IN terminal
AC power input connector.
Connect the provided AC power cord to an AC 
outlet.
  Attach the provided power cord holder to prevent 
accidental disconnection of the AC power cord (☞ 
on the right).
CAUTION
Do not connect the power cord until all other 
connections are completed.
3 REMOTE terminal
Terminal for controlling the monitor by an external 
control. (☞ “External Control” on page 16)
4 VIDEO (INPUT 1/INPUT 2) terminals (BNC)
Input (IN) and output (OUT) terminals for the 
composite signals.
5 COMPO./RGB (G/Y, B/P
B/B-Y, R/PR/R-Y) terminals 
(BNC)
Input (IN) and output (OUT) terminals for the 
analog component (color difference) or analog RGB 
signals.
  Select the signal type in “COMPO./RGB SEL.” 
corresponding to the type of the input signal (☞ 
page 10).
8
Note for connections
  Before making any connections, turn off all the 
equipment.
  Use a cord whose plugs correctly match the 
terminals on this monitor and the equipment.
  Plugs should be firmly inserted; poor connections 
could cause noise.
  When unplugging a cord, be sure to grasp its plug 
and pull it out.
  DO NOT connect the power cord until all connections 
are complete.
  Refer also to the user manual of each piece of 
equipment.
Security slot
Attach a security wire to this slot.
6 EXT.SYNC (CS) terminals (BNC)
Input (IN) and output (OUT) terminals for the 
external composite sync (Cs) signals.
  To use these terminals, set “SYNC INPUT SEL.” 
to “EXT.” (☞ “SYNC FUNCTION” on page 13)
  The terminals are for all VIDEO (INPUT 1, INPUT 
2) and COMPO./RGB.
  When an external sync signal is input, external 
synchronization has priority over all VIDEO 1, 
VIDEO 2 and COMPO./RGB input.
7 AUDIO ASSIGN (IN 1/IN 2) terminals (pin jack)
Input terminals for the analog audio signals.
  Use this terminal for the analog audio connection 
of the SDI.
  Select the video input to assign the audio signal 
in “AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” (☞ 
“AUDIO SETTING” on page 12).8 AUDIO ASSIGN (MONITOR OUT) terminals 
 (pin jack)
Output terminals for the analog audio signal.
  The terminals output the audio signal through 
AUDIO ASSIGN (IN 1 or IN 2) terminals when 
you select the video input you have selected for 
“AUDIO1 ASSIGN.” or “AUDIO2 ASSIGN.” in 
“AUDIO SETTING” (☞ page 12).
  The signal is output from this terminal only when 
the monitor is on or in “P.SAVE” (power save) 
mode. (☞ “NO SYNC ACTION” on page 13)
   The EMBEDDED AUDIO signal...
–  is decoded into an analog signal, then emitted.
–  is emitted only when “SDI 1” or “SDI 2” is 
selected, and when EMBEDDED AUDIO 
signals come in to the E. AUDIO HD/SD SDI 
(IN 1 or IN 2) terminal.
–  has priority over the audio signal input to 
AUDIO ASSIGN (IN 1 or IN 2) terminals when 
“SDI-1” or “SDI-2” is selected for “AUDIO1 
ASSIGN.” or “AUDIO2 ASSIGN.” and the 
EMBEDDED AUDIO signal is input to E.AUDIO 
HD/SD SDI (IN 1 or IN 2) terminal.
9 E. AUDIO HD/SD SDI (IN 1, IN 2) terminals (BNC)
Input terminals for the HD/SD SDI signals.
  The terminals accept also EMBEDDED AUDIO 
signals including up to 12 audio channels with a 
sampling frequency of 48 kHz.
p E. AUDIO HD/SD SDI (SWITCHED OUT) terminal 
(BNC)
Output terminal for the HD/SD SDI signals.
  The SDI signals of the current input (SDI 1 or SDI 
2) are re-clocked, then emitted.
  When an input other than SDI 1 and SDI 2 is 
selected, the SDI signal of the input selected last 
time is emitted from this terminal.
  The signals are emitted from this terminal only 
when the monitor is on or in “P.SAVE” (power 
save) mode.
q DVI-D (HDCP) terminal
Input terminal for the DVI-D signal compatible with 
HDCP.
  When the picture is not displayed correctly, 
change the setting of “DVI INPUT SEL.”
 (☞ page 10).
Using the audio level meter
You can check the conditions of the current 
EMBEDDED AUDIO signals in the audio level meter. 
(☞ “
On the Information Display” on page 7)
Make the setting for the level meter in “LEVEL METER 
SETTING” (☞ “AUDIO SETTING” on page 12).
Attaching the power cord holderThe provided power cord holder prevents accidental 
disconnection of the AC power cord from the AC IN 
terminal.
  The power cord holder consists of two parts, a 
case and a cover.
1
2
3
CAUTION
  Use only the provided screws.
  Make sure the plug will not be pulled out after the 
cover is attached to the case.
 To detach the cover
AC IN terminal
Case
Cover
2 1
DT-V24_20L3D_EN.indd   8DT-V24_20L3D_EN.indd   808.5.27   5:14:58 PM08.5.27   5:14:58 PM
 
						

							9
7 Av ailable signals
The following signals are available for this monitor.
Video signals
No. Signal name Signal format 
shown in the 
status display  (☞  page 7) Input terminal
VIDEO 
(INPUT1,  INPUT2) COMPO./RGB
(Analog 
component/
Analog RGB)*
1
E. AUDIO HD/ SD SDI
(IN 1, IN 2)*
2
D VI-D (HDCP)
(Digital component/ digital RGB)
1 NTSC NTSC √
—— —
2PAL PA L √
—— —
3 B/W50 B/W50 √
—— —
4 B/W60 B/W60 √
—— —
5 480/60i 480/60i — √√ √
6 576/50i 576/50i — √√ √
7 480/60p 480/60p — √
— √
8 576/50p 576/50p — √
— √
9 640*480/60p 640 *480/60p — — — √
10 720/60p 720/60p — √√ √
11 720/50p 720/50p — √√ √
12 720/30p 720/30p — √√
—
13 720/25p 720/25p — √√
—
14 720/24p 720/24p — √√
—
15 1080/60i 1080/60i — √√ √
16 1035/60i 1035/60i — √*
3√
√*3
17 1080/50i 1080/50i — √√ √
18 1080/60p 1080/60p — — — √
19 1080/50p 1080/50p — — — √
20 1080/30p 1080/30p — √√ √
21 1080/25p 1080/25p — √√ √
22 1080/24p 1080/24p — √√ √
23 1080/30psF 1080/60i — √*
3√*3—
24 1080/24psF 1080/24psf — √√
—
√: Acceptable
—: Not acceptable
*1  Analog component/analog RGB signals are compatible with G on sync signal, Y on sync signals, and composite sync 
signals (CS). The separate sync signal (HS/VS) is not compatible.
*2  Compatible with EMBEDDED AUDIO signals
*3  The signal is recognized as 1080/60i.
Computer signals (preset)
DV I-D (HDCP) terminals
No. Signal name Resolution Frequency
Scan system
Horizontal Vertical Horizontal (kHz) Vertical (Hz)
1V GA60 640 480 31.5 59.9 Non-interlace
2W VGA60 852 480 31.5 59.9 Non-interlace
3S VGA60 800 600 37.9 60.3 Non-interlace
4X GA60 1024 768 48.4 60.0 Non-interlace
5W XGA (1280) 1280 768 47.8 60.0 Non-interlace
6WXG A+60
1440 900 55.960.0 Non-interlace
7S XGA60 1280 1024 64.0 60.0 Non-interlace
8W SXGA+60 1680 1050 65.2 60.0 Non-interlace
9UXG A60*
41600 1200 75.0 60.0 Non-interlace
10 WUXGA60*41920 1200 74.0 60.0 Non-interlace
11 720/60p 1280 720 45.0 60.0 Non-interlace
12 1080/60p*
41920 1080 67.5 60.0 Non-interlace
13720/50p 1280 72037.550.0 Non-interlace
141080/50p*41920 108056.2550.0 Non-interlace
*
4  F or DT-V20L3D: When No. 9, 10, 12 or 14 signals come in, thin lines will become obscured becaus\
e their signal 
resolution is higher than the screen resolution.
  Non-preset signals may not be displayed normally even if their frequency is within the acceptable range ( ☞ 
“Horizontal/vertical frequency (computer signal)” on page 21).
  When a preset signal comes in, the signal format is shown on the status display. For other signals, the  resolution is shown.
Specification of the DVI-D (HDCP) terminal
Connect it to the DVI-D output terminal on a personal computer.
Pin No. Input signal Pin No. Input signal Pin No. Input signal 1 T.M.D.S Data 2– 9
T.M.D.S Data 1– 17
T.M.D.S Data 0–
2 T.M.D.S Data 2+ 10
T.M.D.S Data 1+ 18
T.M.D.S Data 0+
3 T.M.D.S Data 2 shield 11
T.M.D.S Data 1 shield 19
T.M.D.S Data 0 shield
4 NC 12
NC 20
NC
5 NC 13
NC 21
NC
6 DDC Clock 14
+5 V Power 22
T.M.D.S Clock shield
7 DDC Data 15
GND 23
T. M . D.S Clock+
8 NC 16
Hot Plug Detect 24
T. M . D.S Clock–
DT-V 24_20L3D _E N .in dd   9DT-V24_20L3D_EN.indd   90 8.5 .2 7   6 :0 0:4 8 P M08.5.27   6:00:48 PM
 
						

							10Menu Configuration—MAIN MENU
PICTURE FUNCTION
Setting for the picture quality
Item To do Setting value
MOVING 
PICTURE*
1Reduce the lag of moving pictures which is peculiar to LCD. OFF, ON
APERTURE 
FREQ.*
2Select the frequency of the luminance signal compensated in 
“APERTURE LEVEL.”OFF, LOW, HIGH
APERTURE 
LEVEL*
2Compensate the frequency response of the luminance signal of the 
video signal.01 – 10
CTI
Adjust the clearness of the outlines of the chrominance signal. OFF, NORMAL, HARD
LT I
Adjust the clearness of the outlines of the luminance signal. OFF, NORMAL, HARD
I/P MODE
Selects a proper mode corresponding to the input picture. NORMAL, CINEMA, 
FIELD
sub menu
Display the sub menu which enables you to adjust the items of “PICTURE FUNCTION” while 
viewing the actual picture.
reset
Restore the default settings for all the items in “PICTURE FUNCTION.”
*
1 DT-V24L3D only
*2 Memorized for each input.
BACK LIGHT
Adjusts the brightness of the display.
DVI INPUT SEL.
When “AUTO” is selected, the format of signals come in to the DVI-D (HDCP) terminal is automatically 
recognized. (Normally, select “AUTO.”)
  Select “MODE1”, “MODE2” or “MODE3” when the picture is not displayed correctly with “AUTO.”
  DVI-D input of the monitor is compatible with HDCP.
COMPO./RGB SEL.
Selects the signal type you want to use for COMPO./RGB terminals. Operation guide
Shows the buttons for each operation. For the operation procedure, see page 7.
  The menu automatically disappears in about 30 seconds after the previous operation.
  Some items may not appear on the menu depending on the input or the input signal.
  The items controlled by the MAKE system do not appear on the menu.Setting value: –20 – +20
Setting value: AUTO, MODE1, MODE2, MODE3
Setting value: COMPO. (component), RGB
DT-V24_20L3D_EN.indd   10DT-V24_20L3D_EN.indd   1008.5.27   5:15:02 PM08.5.27   5:15:02 PM