JVC Av 2987ve Instructions

11
AI ECO SENSOR (ECO)You can adjust TV screen contrast according to the brightness of
your room.
Press the ECO button to select the desired mode.1 Mild contrast (recommended).2 Even contrast.OFF Cancel the function.To operate this function with a menu:
You can display the graphic of AI ECO SENSOR on the screen.
Select the AI ECO DISPLAY in the INSTALL menu, then choose
ON or OFF.Correcting the Slanting Picture (PICTURE TILT)You can correct the picture tilt caused by the earth’s magnetic force.1
Select...

12PIPYou can display a sub picture on the screen.
Press the PIP operation buttons to display and change the sub
picture setting.PIP Display the sub picture.
To cancel, press the PIP button again.
Notes:
•You can hear the sound from the main picture only.
•Main picture and sub picture will use different input
sources, which are TV and VIDEO mode.
When the same input source are selected, the sub
picture input source will change as follows:
Main picture
Sub picture
TV VIDEO-1 = VIDEO-2 = VIDEO-3
VIDEO-1 TV...

13
Original features for picture (continued)Using the List mode
You can store and recall the favorite teletext pages in memory
using the colour buttons.1
In TEXT mode, press the MODE button to enter the List mode.
2
Press a colour button, then press the number buttons to enter
the page number.
3
Press and hold down the 
 (Store) button.
The page number is blinking white to indicate that they are
stored in memory.
4
To store other favorite teletext pages, repeat Step 2 to 3.
To recall the favorite...

14SOUND SYSTEMYou can select an appropriate sound system when abnormal
sound occurs even when the picture appears normally.
Press the SOUND SYSTEM button to select a setting.
This function is not available in video mode.
For the sound system in each country or region, see the table
below:Basic setting for sound
B/G       I       D/K       M
Area Country or Region System
Bahrain, Kuwait, Oman, Qatar, United Arab Emirates,
Yemen, etc. B/G
Indonesia, Malaysia, Singapore, Thailand, India, etc.
Asia, Middle...

15
CINEMA SURROUNDYou can enjoy an enhanced sound for wider audience.
Press the CINEMA SURROUND button to select a setting.OFF Cancel the function.HIGH Listen to sound with more wider audience effect.LOW Listen to sound with less wider audience effect.MONO Listen to mono sound with stereo effect.To operate this function with a menu:
If slight volume distortion occurs when you select HIGH mode,
change the setting to LOW mode. The CINEMA SURROUND
effect will be less noticeable.
If you use CINEMA SURROUND...

16To register the favorite channelYou can register and recall 4 favorite channels by using the
colour buttons (red, green, yellow, blue).1
In TV mode, select a TV channel (PR01-99) you desired to register.
2
Press and hold a colour button for 3 seconds or more.
“FAVORITE CHANNEL 
 PROGRAMMED!” appears on the
screen and current channel is registered.
3
To register other favorite channels, repeat Step 1 to 2.
To recall the favorite channel, press the colour button.
When the TV is in Text mode, Picture in...

17
VNRYou can reduce the picture noise.
Select the VNR in the PICTURE FEATURES menu under
PICTURE menu, then choose a setting of VNR function.OFF VNR is turned off.AUTO Effect of VNR is automatically controlled.MIN Effect of VNR becomes minimum level.MAX Effect of VNR becomes maximum level.If you select MAX, the picture becomes softer even if the original
picture is sharp.LANGUAGEYou can choose your desired on screen display language.
Select the LANGUAGE in the INSTALL menu, then choose a...

18
MENU
INSTALL menu
VIDEO-2 SETTING
❇AUTO SHUTOFFYou can set the TV to turn off automatically when no signal is
received for about 15 minutes or longer after the end of a
broadcast.
Select AUTO SHUTOFF in INSTALL menu, then choose ON or
OFF.
The AUTO SHUTOFF function does not turn off the TV’s main
power.
The AUTO SHUTOFF function is not available in video mode.VIDEO-2 SETTINGYou can set the VIDEO-2 SETTING according to the video signal
output from the external devices connected to the VIDEO-2...

19
To register the TV channels automaticallyYou can register the TV channels into the TV’s channel list
automatically.1
Display the INSTALL menu.
2
Choose AUTO PROGRAM, then press the MENU/OK button.
AUTO PROGRAM function starts, and the channels received
are registered in the channel list (PR list) automatically.
3
“SETUP TOUR RESTART?” appears.To start the SETUP Press the MENU/OK button. Then proceed toTOUR step 5 of “Setting up your TV” on page 8.
To skip the SETUP Press the Red button.TOUR
4
The EDIT...

20
To add in the new channel
(INSERT in the EDIT menu)You can add in the new channel in the TV channel list as you like.
You need to find the “CH/CC” number for the TV channel. Find the
“CH/CC” number corresponding to the channel number of the TV
channel from the attached sheet “CH/CC number list” on page 21.1
Display the INSTALL menu.
2
Choose EDIT/MANUAL, then press the MENU/OK button.
EDIT menu appears.
3
Choose the PR number for which you will register a new TV
channel. When you add a new TV channel...