JVC Av 2957we Instructions

							11
AI ECO SENSOR (ECO)You can adjust TV screen contrast according to the brightness of
your room.
Press the ECO button to select the desired mode.1 Mild contrast (recommended).2 Even contrast.OFF Cancel the function.To operate this function with a menu:
You can display the graphic of AI ECO SENSOR on the screen.
Select the AI ECO DISPLAY in the INSTALL menu, then choose
ON or OFF.Correcting the Slanting Picture (PICTURE TILT)You can correct the picture tilt caused by the earth’s magnetic force.1
Select the PICTURE TILT in the PICTURE FEATURES menu
under PICTURE menu, then press MENU/OK button.
The following display appears.
2
Press the 5/∞ buttons until the picture become level. Then
press the MENU/OK button.COMPRESS (16:9)You can convert a normal picture (4:3 aspect ratio) into a wide
picture (16:9 aspect ratio).
Select the COMPRESS (16:9) in the PICTURE FEATURES menu
under PICTURE menu, then choose ON or OFF.BLUE BACKYou can set the TV to automatically change to a blue screen and
mute the sound if the signal is weak or absent, or when there is
no input from an antenna.
Select the BLUE BACK in the INSTALL menu, then choose ON or
OFF.
If you wish to continue viewing the poor picture, cancel the BLUE
BACK function.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
Advanced setting for picture
MENU
FEATURES menu
AI ECO SENSOR
MENU
PICTURE menu
PICTURE FEATURES menu
PICTURE TILTBACK  

 
OK
.
MENU
PICTURE menu
PICTURE FEATURES menu
COMPRESS (16:9)
MENU
INSTALL menu
BLUE BACK
❇
❇
❇ ❇
PICTURE TILT
MENU
INSTALL menu
AI ECO DISPLAY
❇
GGT0093-001A-H(EN)21/04/2005, 7:38 PM 11
 
						

							12PIPYou can display a sub picture on the screen.
Press the PIP operation buttons to display and change the sub
picture setting.PIP Display the sub picture.
To cancel, press the PIP button again.
Notes:
•You can hear the sound from the main picture only.
•Main picture and sub picture will use different input
sources, which are TV and VIDEO mode.
When the same input source are selected, the sub
picture input source will change as follows:
Main picture
Sub picture
TV VIDEO-1 = VIDEO-2 = VIDEO-3
VIDEO-1 TV
 = VIDEO-2
 = VIDEO-3
VIDEO-2 TV
 = VIDEO-1
 = VIDEO-3
VIDEO-3 TV
 = VIDEO-1
 = VIDEO-2
SUB-P -/+ Select the desired channel for sub picture. (Input) Select the input source for the sub picture. (Swap) Swap between the main picture and sub picture. (Position) Change the sub picture position.
Each time you press on 
 (Position) button, the sub
picture position will change as follows:
 (Freeze) Freeze the sub picture to be still.To operate this function with a menu:
When VIDEO-2  is set to component, you can’t select VIDEO-2
for sub picture.Original features for picture
When VIDEO-2  is set to component, if the input source of main
picture is set to VIDEO-2 with component, PIP button is disabled
and sub picture can’t be displayed.TELETEXTYou can watch the Teletext broadcast channel with TEXT function.1
Press the TEXT button to select the desired mode as follows:
2
Press the CHANNEL -/+ buttons, number buttons or colour
buttons to select other Teletext pages.
3
Press TEXT or TV/VIDEO button to return to TV mode.
You can also operate the teletext using the following buttons: (Hold) Hold a teletext page.
The 
 (hold) are displayed at the top left of the screen.
To cancel, press 
 (Hold) button again.
 (Reveal) Display the hidden text (e.g. answers to a quiz).
To cancel, press 
 (Reveal) button again.
 (Size) Enlarge the teletext display. (Index) Return to the index page instantly. (Cancel) Watch TV programme while waiting for a teletext page.
When the teletext page is found, a page number
appears at the upper left of the screen.
Press 
 (Cancel) to view the teletext page.
 (Sub-page) Operate the 
 (Sub-page) function.
Sub-page numbers are displayed at the left of the
screen.
To cancel sub-page function, press 
 (Sub-page)
button again.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
lower right      lower left       upper left
upper right
MENU
FEATURES menu
PIP
TV mode TEXT mode
MIX mode
❇
GGT0093-001A-H(EN)21/04/2005, 7:38 PM 12
 
						

							13
Original features for picture (continued)Using the List mode
You can store and recall the favorite teletext pages in memory
using the colour buttons.1
In TEXT mode, press the MODE button to enter the List mode.
2
Press a colour button, then press the number buttons to enter
the page number.
3
Press and hold down the 
 (Store) button.
The page number is blinking white to indicate that they are
stored in memory.
4
To store other favorite teletext pages, repeat Step 2 to 3.
To recall the favorite teletext page, press the MODE button, then
press the colour button.
To exit the List mode, press the MODE button again.
When viewing teletext programme, menu operations are not available.
If characters on a teletext programme do not appear properly,
change the TEXT LANGUAGE setting.
TEXT LANGUAGEYou can set the Teletext language group that corresponds to the
programmes.
Select TEXT LANGUAGE in the INSTALL menu, then choose the
desired language group.GROUP-1 English, German, Swedish / Finnish / Danish / Hungar-
ian, Italian, French, Spanish / Portuguese, Turkish
GROUP-2 Polish, German, Estonian, Slovenian, Czech /Slovakian, Rumanian
GROUP-3 Polish, German, Estonian, Lettish, Russian, UkrainianDepending on the broadcast, the language set may not display
properly.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.MENU
INSTALL menu
TEXT LANGUAGE
❇
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 13
 
						

							14SOUND SYSTEMYou can select an appropriate sound system when abnormal
sound occurs even when the picture appears normally.
Press the SOUND SYSTEM button to select a setting.
This function is not available in video mode.
For the sound system in each country or region, see the table
below:Basic setting for sound
B/G       I       D/K       M
Area Country or Region System
Bahrain, Kuwait, Oman, Qatar, United Arab Emirates,
Yemen, etc. B/G
Indonesia, Malaysia, Singapore, Thailand, India, etc.
Asia, Middle China, Vietnam, etc. D/KEast Hong Kong, etc. I
Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. B/GPhilippines, Taiwan, Myanmar, etc. MRussia, etc. D/K
EuropeCzech Republic, Poland, etc. D/K
Germany, Holland, Belgium, etc. B/GUK, etc. I
Oceania Australia, New Zealand, etc. B/G
Republic of South Africa, etc. I
Africa Nigeria, etc. B/G
Egypt, Morocco, etc. B/G
SOUND MODEYou can choose the desired sound setting.
Select the SOUND MODE in SOUND menu, then choose the
setting.USER You can change this sound setting as you like.
Select USER and adjust the frequencies in EQUALIZER
(100, 300, 1K, 3K, 8K Hz).
For details, see “EQUALIZER” on page 15.
DYNAMIC Emphasize on both vocal sound and music.MUSIC Emphasize on music effect.NEWS Emphasize on vocal sound.BALANCEYou can adjust the volume balance between the left and right
speakers.
Select the BALANCE in SOUND menu, then adjust the setting.SOUND TURBOYou can enjoy the emphatic low and high frequency levels.
Press the SOUND TURBO to select ON or OFF.
To operate this function with a menu:
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
MENU
SOUND menu
SOUND MODE
MENU
SOUND menu
BALANCE
❇
❇
MENU
SOUND menu
SOUND TURBO
❇
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 14
 
						

							15
CINEMA SURROUNDYou can enjoy an enhanced sound for wider audience.
Press the CINEMA SURROUND button to select a setting.OFF Cancel the function.HIGH Listen to sound with more wider audience effect.LOW Listen to sound with less wider audience effect.MONO Listen to mono sound with stereo effect.To operate this function with a menu:
If slight volume distortion occurs when you select HIGH mode,
change the setting to LOW mode. The CINEMA SURROUND
effect will be less noticeable.
If you use CINEMA SURROUND and SOUND TURBO together,
volume distortion might occurs.STEREO / I

II ( 
 )
You can enjoy the stereo and bilingual broadcasted programmes.
Press the 
 button to select the desired mode.Select stereo sound.Select monaural sound.
ISelect bilingual I (sub I).IISelect bilingual II (sub II).
MONO Cancels the Multi Sound function, and the sound
becomes monaural.
This function is not available in video mode.
To operate this function with a menu:Advanced setting for sound
MENU
SOUND menu
CINEMA SURROUND
MENU
SOUND menu
STEREO / I

II
EQUALIZERYou can adjust the sound level of each frequencies when
selecting USER mode in SOUND MODE.1
Select the USER in SOUND MODE under SOUND menu.
2
Select the EQUALIZER in SOUND menu.
The following display appears.
3
Select and adjust the desired frequencies.
4
Press the MENU/OK button to exit the menu.
Adjust high frequency will affect higher pitch sound and vice versa.AI VOLUMEYou can adjust the volume of all the channels and video inputs to
the same level automatically.
Select the AI VOLUME in SOUND menu, then choose ON or OFF.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
MENU
SOUND menu
SOUND MODE
USER
MENU
SOUND menu
EQUALIZER
EQUALIZER
IIIIIIIIIIII
IIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIII100 300 1K 3K 8K HzBACK  
 
 
OK
.
MENU
SOUND menu
AI VOLUME
❇
❇❇
❇
❇
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 15
 
						

							16To register the favorite channelYou can register and recall 4 favorite channels by using the
colour buttons (red, green, yellow, blue).1
In TV mode, select a TV channel (PR01-99) you desired to register.
2
Press and hold a colour button for 3 seconds or more.
“FAVORITE CHANNEL 
 PROGRAMMED!” appears on the
screen and current channel is registered.
3
To register other favorite channels, repeat Step 1 to 2.
To recall the favorite channel, press the colour button.
When the TV is in Text mode, Picture in Picture or menu mode,
favorite channel function is not available.To adjust favorite channel setting
(FAVORITE CH SETTING)You can adjust the picture and sound settings for the favorite channels.1
Display the PICTURE menu and select FAVORITE CH
SETTING in PICTURE FEATURES menu.
2
Select FAVORITE CHANNEL in FAVORITE CH SETTING
menu, then choose the desired favorite channel.
3
Select EFFECT, then press 2/3 button
to choose ON.
To cancel the settings, choose OFF.
Favorite channel and video setting
MENU
PICTURE menu
PICTURE FEATURES menu
FAVORITE CH SETTING
FAVORITE CH SETTING
FAVORITE CHANNEL
4
Select the desired item that you wish to adjust.
5
Press the MENU/OK button to exit the menu.To adjust the video setting (VIDEO SETTING)You can adjust the picture and sound settings for video inputs.1
Display the PICTURE menu and select VIDEO SETTING in
PICTURE FEATURES menu.
2
Select VIDEO STATUS in VIDEO SETTING menu, then
choose the desired video input.
3
Select EFFECT, then press 2/3 button
to choose ON.
To cancel the settings, choose OFF.
4
Select the desired item that you wish to adjust.
5
Press the MENU/OK button to exit the menu.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.MENU
PICTURE menu
PICTURE FEATURES menu
VIDEO SETTING
VIDEO SETTING
VIDEO STATUS
CONTRAST       BRIGHT       SHARP       COLOUR
SOUND MODE (USER, DYNAMIC, MUSIC, NEWS)TINT
❇
❇❇ ❇
CONTRAST       BRIGHT       SHARP       COLOUR
SOUND MODE (USER, DYNAMIC, MUSIC, NEWS)TINT
FAVORITE CH SETTINGFAVORITE CHANNEL 

 PR 01
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
SOUND MODE  USER
EFFECT ON
BACK  
   
 
OK 
.
VIDEO SETTINGVIDEO STATUS  VIDEO-1
CONTRAST
BRIGHT
SHARP
COLOUR
TINT
SOUND MODE  USER
EFFECT ONBACK  
   

RESET 
 OK
 
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 16
 
						

							17
VNRYou can reduce the picture noise.
Select the VNR in the PICTURE FEATURES menu under
PICTURE menu, then choose a setting of VNR function.OFF VNR is turned off.AUTO Effect of VNR is automatically controlled.MIN Effect of VNR becomes minimum level.MAX Effect of VNR becomes maximum level.If you select MAX, the picture becomes softer even if the original
picture is sharp.LANGUAGEYou can choose your desired on screen display language.
Select the LANGUAGE in the INSTALL menu, then choose a
language.Customized setting
MENU
PICTURE menu
PICTURE FEATURES menu
MENU
INSTALL menu
LANGUAGE
CHILD LOCKYou can disable the front control buttons of the TV.
Select the CHILD LOCK in the FEATURES menu, then choose
ON or OFF.OFF TIMERYou can set the TV to turn off automatically to standby mode after
a set time.
Press the OFF TIMER button to select a desired period of time.
You can set the period of time
to a maximum of 120 minutes
in 10 minutes step.
To operate this function with a menu:
When the elapsed of time left one minute, “GOOD NIGHT!”
appears on the screen.
You can display the OFF TIMER menu again to confirm or
change the remaining time.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
MENU
FEATURES menu
CHILD LOCK
OFF TIMER
0 120
10
BACK  
   
 
OK 
.
MENU
FEATURES menu
OFF TIMER
❇
❇❇
❇
VNR
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 17
 
						

							18
MENU
INSTALL menu
VIDEO-2 SETTING
❇AUTO SHUTOFFYou can set the TV to turn off automatically when no signal is
received for about 15 minutes or longer after the end of a
broadcast.
Select AUTO SHUTOFF in INSTALL menu, then choose ON or
OFF.
The AUTO SHUTOFF function does not turn off the TV’s main
power.
The AUTO SHUTOFF function is not available in video mode.VIDEO-2 SETTINGYou can set the VIDEO-2 SETTING according to the video signal
output from the external devices connected to the VIDEO-2
terminal.
Select the VIDEO-2 SETTING in INSTALL menu, then choose a
setting.VIDEO If a normal video signal (composite video signal) is
input.
COMPONENT If a component video signal (Y/C
B/CR) is input.
For connecting methods, see “Additional Preparation” on page
22.Customized setting (continued)
MENU
INSTALL menu
AUTO SHUTOFF
MENU
INPUT menu
EXT. INPUT
MENU
INPUT menu
DISPLAY
❇❇
❇
EXT. INPUT (TV/VIDEO)You can select TV or video terminal input with one touch.
Press the TV/VIDEO button to select an input.
To operate this function with a menu:DISPLAYYou can display the programme number, video terminal number
and PR list on the screen.
Press the DISPLAY button to select the desired mode:
Choose a TV channel or a VIDEO terminal.1
Press the DISPLAY button to display the PR LIST.
2
Select a programme number or video terminal by pressing the
5/∞ button to move up/down on the programme number or
press the 2/3 button to skip for each 7 programme numbers,
then press MENU/OK button.
To operate this function with a menu:
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
PR LIST 
           -7    
OK     +7
PR   CH/CC
AV    
 1 
 CH 03
 2 
 CH 05
   3 
 CH 07  
   4 
 CH 09  
   5    CC 04   
   6    CC 05   
.
.
ON            OFF            PR LIST
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 18
 
						

							19
To register the TV channels automaticallyYou can register the TV channels into the TV’s channel list
automatically.1
Display the INSTALL menu.
2
Choose AUTO PROGRAM, then press the MENU/OK button.
AUTO PROGRAM function starts, and the channels received
are registered in the channel list (PR list) automatically.
3
“SETUP TOUR RESTART?” appears.To start the SETUP Press the MENU/OK button. Then proceed toTOUR step 5 of “Setting up your TV” on page 8.
To skip the SETUP Press the Red button.TOUR
4
The EDIT menu appears.To edit the channel Proceed to the Step 3 of “To edit the channellist  list (PR LIST)” on page 20.
If a channel is not Proceed to the Step 3 of “To register the TVregistered channels manually” on this page.To exit the menu Press the MENU/OK button.
For details of “SETUP TOUR”, see page 8.To register the TV channels manually
(MANUAL in the EDIT menu)You can register the TV channels into the TV’s channel list manually.1
Display the INSTALL menu.
TV channel presetting
2
Choose EDIT/MANUAL, then press the MENU/OK button.
EDIT menu appears.
3
Choose the channel which you want to register.
4
Press the blue button to activate the MANUAL function.
The sound system of the channel appears at the right of the
CH/CC number.
5
Press the 3 button to choose an appropriate sound system.
For details, see “SOUND SYSTEM” on page 14.
6
Press the green or red button to search for the TV channel.
Searching stops when a channel is found and displayed.
7
Repeat step 5 until your desired TV channel appearsIf the reception is poor Press the blue or yellow button to fine tune
the TV channel.
If noisy sound is heard Press the 3 button to choose an appropriatesound system.
8
Press the MENU/OK button to exit the menu.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
EDITBACK  
     

INSERT
 
OK MOVE 

DELETE
   

MANUAL
PR   CH/CC
 7    CH 09 
 8    CH 11
 9 
 CH 13 
3
 10   
 11  
 12   
 13   .
MENU
INSTALL menu
❇MENU
INSTALL menu
❇
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 19
 
						

							20
To add in the new channel
(INSERT in the EDIT menu)You can add in the new channel in the TV channel list as you like.
You need to find the “CH/CC” number for the TV channel. Find the
“CH/CC” number corresponding to the channel number of the TV
channel from the attached sheet “CH/CC number list” on page 21.1
Display the INSTALL menu.
2
Choose EDIT/MANUAL, then press the MENU/OK button.
EDIT menu appears.
3
Choose the PR number for which you will register a new TV
channel. When you add a new TV channel of NTSC-M system,
press the SOUND SYSTEM button to change the sound
system to M. Then proceed to the next step.
4
Press the green button, then press 5/∞ buttons to choose
“CC” or “CH”.
5
Press the number button to enter the remaining CH/CC
number.
The TV starts to search the TV channel, and the picture of the
TV channel appears. If the TV finds no TV channel, a noisy
picture appears.
When a TV channel has already been registered in PR99, using
the INSERT function deletes that TV channel.
❇About the basic operations of the menu, please see the “How
to operate menus and menus locations” on page 5.
TV channel presetting (continued)To edit the channel list (PR LIST)
(MOVE and DELETE in the EDIT menu)You can edit the TV channel list as you like.
Note: After this operation, other channel’s PR numbers will be
changed.1
Display the INSTALL menu.
2
Choose EDIT/MANUAL, then press the MENU/OK button.
EDIT menu appears.
3
Choose the channel which you want to change PR number, or
delete.
4
Do the following action:To change the PR Press the 3 button. Then move it to the PR
number (MOVE) number you want to use it for the channel.
Finally press the 2 button.
To delete the Press the yellow button.
channel (DELETE)
5
Press the MENU/OK button to exit the menu.
EDITBACK  
     

INSERT
 
OK MOVE 

DELETE
   

MANUAL
PR   CH/CC
 7    CH 09 
 8    CH 11
 9 
 CH 13 
3
 10   
 11  
 12   
 13   .
MENU
INSTALL menu
❇
MENU
INSTALL menu
❇
GGT0093-001A-H(EN)21/04/2005, 7:39 PM 20