JVC Av 2106be Instructions

							11
Using the TV’s menus
ON TIMER
Your TV will automatically turn on and
tune into the channel you set after the
period of time you set.
1Press MENU T to display the
“MENU 1” menu, then select
“ON TIMER”.
          MENU        1
  INPUT               TV
  ON TIMER
              PR 1  0:00
  VNR                OFF
 OPERATE BY VOL-+
 SELECT  BY      EXIT BY
 PROGRAM BY -+
    DISPLAY


	
2Press MENU M to select a channel
you want to view when the TV turns
on.
3Press VOLUME M to select the
period of time after which you want
to turn on the TV.
The ON TIMER function starts.
•Each time you press the button, the period
of time changes in 15 minute intervals (up
to 12 hours).
To cancel the ON TIMER function,
press the VOLUME m button to set the
period of time to “0:00”.
4Press DISPLAY to turn the display
off.
•If you turn off the TV’s main power by
pressing the Main power button, the ON
TIMER function is canceled.
•If you do not turn off the TV after starting
the ON TIMER function, the channel will
automatically switch to the channel set for
the ON TIMER function.
When the time set for the ON TIMER
function is reached:
The TV automatically turns on and the
channel set for the ON TIMER function is
displayed.
•For safety reasons the TV will automatically
turn off if no operations are made within
approximately two hours after the TV is
turned on with the ON TIMER function.
•The OFF TIMER function and AUTO
SHUTOFF function have priority over the ON
TIMER function.
INPUT
You can view images from VCRs or other
devices connected to your TV.
1Press MENU T to display the
“MENU 1” menu, then select
“INPUT”.
          MENU        1
  INPUT               TV
  ON TIMER
              PR 1  0:00
  VNR                OFF
 
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to select the VIDEO
mode.
While you press MENU –/+, it will
switch to TV mode and VIDEO mode
alternately.
 GGT0106-001B-H_P10-13 16/3/06, 9:56 AM11
 
						

							12
Using the TV’s menus
VNR (Video Noise Reduction)
You can reduce the picture noise.
1Press MENU T to display the
“MENU 1” menu, then select “VNR”.
          MENU        1
  INPUT               TV
  ON TIMER
              PR 1  0:00
  VNR                 ON
 
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to select “ON”.
To cancel the VNR function, select
“OFF”.
AUTO SHUTOFF
You can set your TV to turn off if no
signals are received for about 15 minutes
or longer after the end of a broadcast.
1Press MENU T to display the
“MENU 2” menu, then select “AUTO
SHUTOFF”.
          MENU        2
  AUTO SHUTOFF        ON
  CHILD LOCK          ON
  BLUE BACK           ON
  
  
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to select “ON”.
To cancel the AUTO SHUTOFF function,
select “OFF”.
•The AUTO SHUTOFF function does not
turn off the TV’s main power.
•The AUTO SHUTOFF will not work for a
VIDEO mode.
CHILD LOCK
You can disable the front control buttons
of the TV.
When this function is set to “ON”, the TV
can be operated using only the remote
control.
Use this function to prevent children from
operating the TV without parental consent.
1Press MENU T to display the
“MENU 2” menu, then select “CHILD
LOCK”.
          MENU        2
  AUTO SHUTOFF        ON
  CHILD LOCK          ON
  BLUE BACK           ON
   
  
  
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to select “ON”.
To cancel the CHILD LOCK function,
select “OFF”.
•The CHILD LOCK function is canceled when
you turn the power off.
BLUE BACK
You can mute the sound and change the
picture into a blue screen while no signals
are received by the TV, or when the
signals are unstable.
1Press MENU T to display the
“MENU 2” menu, then select “BLUE
BACK”.
          MENU        2
  AUTO SHUTOFF        ON
  CHILD LOCK          ON
  BLUE BACK           ON
  
  
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to select “ON”.
To cancel the BLUE BACK function,
select “OFF”.
•To view a broadcast even when the
reception signal is poor, set the BLUE
BACK function to “OFF”.
•Even when the BLUE BACK function is set
to “OFF”, the sound may not be audible.
 GGT0106-001B-H_P10-13 16/3/06, 9:56 AM12
 
						

							13
Using the TV’s menus
SETUP TOUR
You can start the SETUP TOUR function.
1Press MENU T to display the
“MENU 3” menu, then select
“SETUP TOUR”.
          MENU        3
  AUTO CH PRESET        
  MANUAL CH PRESET
  SETUP TOUR
  LANGUAGE       ENGLISH
   
                       
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M.
JVC logo is appear and the SETUP
TOUR function will start.
For details, see page 6.
LANGUAGE
You can select the language for the on-
screen display.
1Press MENU T to display the
“MENU 3” menu, then select
“LANGUAGE”.
          MENU        3
  AUTO CH PRESET        
  MANUAL CH PRESET
  SETUP TOUR
  LANGUAGE       ENGLISH
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to select
language.
The on-screen display indications are
in the selected language.
AUTO CH PRESET
You can automatically preset all TV
channels that can be received by your TV
to channels.
1Press MENU T to display the
“MENU 3” menu, then select “AUTO
CH PRESET”.
          MENU        3
  AUTO CH PRESET        
  MANUAL CH PRESET
  SETUP TOUR
  LANGUAGE       ENGLISH
 
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M to start the AUTO
CH PRESET function.
“>>>ON SEARCH” is displayed on
the screen.
When all the TV channels that can be
received on your TV have been preset,
the display goes out and the AUTO CH
PRESET function operation is
completed.
To stop the AUTO CH PRESET:
Press the MENU m buttons.
•The AUTO CH PRESET function does not
preset a TV channel to the AV channel
(channel number 0).
•If the TV cannot preset the TV channel you
want to view, preset it manually. For details,
see “MANUAL CH PRESET” on page 14.
 GGT0106-001B-H_P10-13 16/3/06, 9:56 AM13
 
						

							14
Using the TV’s menus
MANUAL CH PRESET
You can manually preset desired TV
channels to desired channels.
1Press MENU T to display the
“MENU 3” menu, then select
“MANUAL CH PRESET”.
          MENU        3
  AUTO CH PRESET        
  MANUAL CH PRESET
  SETUP TOUR
  LANGUAGE       ENGLISH
 
 SELECT  BY      EXIT BY
 OPERATE BY -+    
 DISPLAY
2Press MENU M.
The sub-menu is displayed.
   MANUAL
   FINE
   SKIP              NO
   SOUND SYSTEM     B/G
   EXIT
SELECT  BY       PR 1 VL
PROGRAM BY -+    EXIT BY
SEARCH  BY VOL-+  
 DISPLAY
•The channel number is displayed as a PR
number. For example, channel 1 will be
displayed as PR 1. However, the AV
channel will be displayed as AV.
3Press MENU M to select the
channel number.
4Press VOLUME M to start
searching for the TV channel.
“>>>” or “” or “
						

							15
Using the TV’s menus
SKIP
You can set undesired channels to be
skipped. Channels set to be skipped
cannot be selected by the CHANNEL m
buttons nor the CHANNEL SCAN button.
•Channels to which TV channels have not
been preset are automatically set to be
skipped.
1Press MENU T to display the
“MENU 3” menu, then select
“MANUAL CH PRESET”.
2Press MENU M.
The sub-menu is displayed.
3Press MENU T to select “SKIP”.
   MANUAL
   FINE
   SKIP              NO
   SOUND SYSTEM     B/G
   EXIT
SELECT  BY       PR 3 VL
PROGRAM BY -+    EXIT BY
YES/NO  BY VOL-+  
 DISPLAY
4Press MENU M to select the
channel you want to skip.
5Press VOLUME M to select “YES”.
The channel is set to be skipped.
To cancel the SKIP function, select
“NO”.
6Repeat steps 4 and 5 if you want to
set another channel to skip.
Picture Adjustments
You can adjust the picture as you like.
1Press MENU T to display the
“MENU 4” menu.
         MENU        4
TINT
COLOUR
BRIGHT
CONT.
SHARP
SELECT  BY      EXIT BY
OPERATE BY -+    
 DISPLAY
2Press MENU T to select an item
and press MENU M to adjust it.
TINT*- : Reddish + : Greenish
COLOUR- : Lighter + : Deeper
BRIGHT- : Darker + : Brighter
CONT.- : Lower + : Higher
SHARP- : Softer + : Sharper
*TINT (tint) is displayed only when
viewing images from NTSC3.58 or
NTSC4.43 colour systems.
 GGT0106-001B-H_P14-17 16/3/06, 9:56 AM15
 
						

							16
Using the buttons on the TV
1MENU button
• MENU 
 button
2CHANNEL m buttons
• MENU m buttons
3VOLUME m buttons
• EXIT from MENU buttons
4Remote control sensor
5ON TIMER lamp
The light is switched on
while ON TIMER function
is operating.
6POWER lamp
When the Main power is
on, the light is red.
7POWER/ON TIMER lamp
When the Main power is
on, the light is green.
When ON TIMER function
is on, it is red.
8Main power button 


MENU CHANNEL VOLUME
EXITPOWER /
ON  TIMER
123
784
MENUCHANNELVOLUME
EXITON TIMER POWER
1234568
MENU CHANNEL VOLUME
EXITPOWER /
ON  TIMER
123478

MENU CHANNEL VOLUME
ON
POWER
TIMER
EXIT
123478

MENUCHANNELVOLUMEEXITONTIMERPOWER
123
65
84
 GGT0106-001B-H_P14-17 16/3/06, 9:56 AM16
 
						

							17
Using the buttons on the TV
Basic operation
•Check to make sure the CHILD LOCK
function is set to “OFF”. When the CHILD
LOCK function is set to “ON”, the TV cannot
be operated using the front control buttons.
For details, see “CHILD LOCK” on page 12.
1Press CHANNEL M to turn the TV
on from standby mode.
2Press CHANNEL M to select a
channel.
3Press VOLUME M to adjust the
volume.
4To turn your TV off, press the Main
power button to turn off the TV’s
main power.
To change the TV mode to the VIDEO
mode:
•Select the VIDEO mode with the INPUT
function in “MENU 1”.
Operating menus
You can operate functions in menus using
the front control buttons on the TV.
1Press MENU y to display a menu.
2Press MENU y repeatedly to display
the menu you want to use.
3Press MENU y to select the desired
function or item.
4Press MENU M or VOLUME M to
carry out the desired operation.
For details, see the description for each
function.
5Press VOLUME M to turn the menu
display off.
To turn the sub-menu display off:
1Press MENU y to select “EXIT”.
   MANUAL
   FINE
   SKIP              NO
   SOUND SYSTEM      B/G
   EXIT
SELECT  BY       PR 3 VL
PROGRAM BY -+    EXIT BY
EXIT    BY VOL-+  
 DISPLAY
2Press VOLUME m to turn the display
off.
 GGT0106-001B-H_P14-17 16/3/06, 9:56 AM17
 
						

							18
Troubleshooting
If there is no picture or the TV does not operate normally, make sure the problem isn’t due
to the reasons indicated below.
If the problem persists even after taking the measures indicated, please contact a service
technician.
Poor picture
•Press the COLOUR SYSTEM button to select
another colour system. (see page 8.)
•Adjust the picture settings. (see page 15.)
•Set the Picture mode to STANDARD.
(see page 8.)
•If noise (snow) totally blocks out the picture,
check the following.
-Have the TV and aerial been connected
properly?
-Has the aerial cable been damaged?
-Is the aerial pointing in the right direction?
-Is the aerial itself faulty?
•If the TV or aerial suffer interference from
other equipment, stripes or noise may appear
in the picture. Move any equipment which
can cause interference away from the TV.
•If the TV or aerial suffer interference from
signals reflecting from mountains or
buildings, double-pictures (ghosting) will
occur. Change the aerial’s direction or replace
it with an aerial with better directionality.
•When a white and bright still image (such as
a white dress) is displayed on the screen, the
white part may look as if it is coloured. When
the image disappears from the screen, the
unnatural colours will also disappear.
The TV turns on suddenly
•Is the ON TIMER function set to operate?
(see page 11.)
The TV channel changes suddenly
•Is the ON TIMER function set to operate?
(see page 11.)
Cannot turn the TV on
•Press the Main power button on the TV.
•Connect the power cord to the AC outlet.
The screen turns blue
•Is the BLUE BACK function on? (see page 12.)
Remote control inoperable
•Replace the batteries. (see page 3.)
Buttons on front of the TV do not work
•Switch the CHILD LOCK function off.
(see page 12.)
TV does not respond immediately
•Press the main power button on the TV to
turn off the main power. Press the main
power button again to turn on the TV. If the
TV returns to a normal state, operation is
normal.
The TV turns off suddenly
•Is the OFF TIMER function set to operate?
(see page 9.)
•Is the AUTO SHUTOFF function on?
(see page 12.)
•Have you not performed an operation for
about two hours after the TV was switched on
by the ON TIMER function? (see page 11.) If
you don’t perform an operation within about
two hours, the TV is automatically switched
off for safety.
Poor sound
•Press the SOUND SYSTEM button to select
another sound system. (see page 8.)
 GGT0106-001B-H_P18-19 16/3/06, 9:56 AM18
 
						

							19
Asia,
Middle
East
Specifications
TV RF systems
B, G, I, D, K, K1
Colour systems
PAL, SECAM, NTSC 3.58 MHz/NTSC 4.43 MHz (in VIDEO mode only)
Receiving channels
VHF low channel (VL), VHF high channel (VH), UHF channel (U)
Receives cable channels in mid band, super band and hyper band.
External input / output
INPUT: VIDEO input (RCA), AUDIO input (RCA)
OUTPUT: VIDEO output (RCA), AUDIO output (RCA)
Headphone jack: stereo mini jack (3.5 mm diameter)
Accessories
•Remote control unit: RM-C360GY
•AA / R6 / UM-3 dry cell battery × 2
Design and specifications subject to change without notice.
Broadcasting systems
Area Country or RegionSystemColour Sound
Bahrain, Kuwait, Oman, Qatar,
United Arab Emirates, Yemen, etc. PAL B/G
Indonesia, Malaysia, Singapore, Thailand,
India, etc.
China, Vietnam, etc. PAL D/K
Hong Kong, etc. PAL I
Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. SECAM B/G
Philipins, Taiwan, Myanmar, etc. NTSC M
Russia, etc. SECAM D/K
EuropeCzech Republic, Poland, etc. PAL D/K
Germany, Holland, Belgium, etc. PAL B/G
UK, etc. PAL I
OceaniaAustralia, New Zealand, etc. PAL B/G
Republic of South Africa, etc. PAL I
AfricaNigeria, etc. PAL B/G
Egypt, Morocco, etc. SECAM B/G
 GGT0106-001B-H_P18-19 16/3/06, 9:57 AM19
 
						

							 GGT0106-001B-H_Cover 16/3/06, 9:55 AM2