Juiceman Juice Extractor JM1 User Manual

LIMITED ONE YEAR WARRANTY
Warranty:
This Juiceman® product is warranted by Salton, Inc. to be free from defects in materials or
workmanship for a period of (1) year from the original purchase date. This product warranty covers only the
original consumer purchaser of the product.
Warranty Coverage:
This warranty is void if the product has been damaged by accident in shipment,
unreasonable use, misuse, neglect, improper service, commercial use, repairs by unauthorized personnel,
normal wear and tear,...

14
NOTES
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed including the following:
1. Read all instructions.
2. To protect against risk of electrical shock do not put cord, plugs, or
appliance in water or other liquid.
3. Close supervision is necessary when any appliance is used by or 
near children.
4. Unplug from outlet when not in use, before putting on or taking off
parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate...

TROUBLESHOOTING  
(Continued)
Possible CorrectionImproper fit between the Blade Basket and Hub can cause parts of 
the Juice Bowl to rub against the Blade Basket. If this is the case, 
call Consumer Service at (800) 233-9054.
Certain produce (pineapples and overripe produce) may build up on
Blade Basket, causing pulp to eject before juice is completely extracted.
Fruit tends to produce wetter pulp than vegetables. If problem persists,
rinse Blade Basket.
Try a different wall outlet. Also let Juicer sit...

TROUBLESHOOTING
Possible CorrectionTry juicing slower, as wet produce is more likely to build up in Cover.
To release pulp, lightly tap on the side of the Cover. Empty Pulp
Basket if full.
Blade Basket may not have been seated correctly, causing it to
become unseated during use. Should this be the case, check  the 
gear teeth of the Blade Basket and the Motor Base for damage. If any
teeth are damaged, call Consumer Service at (800) 233-9054.
Snug seating is desirable. To insert, try seating the Blade...

11
CLEANING YOUR JUICER  
(Continued)
After cleaning and reassembly is complete, your new Juicer is
ready to go to work! Before starting, make sure the Blade
Basket is securely seated and the Pulp Basket is at the rear of
the Juicer to receive pulp. The pulp from your Juicer can be
used in many different applications such as breads, muffins,
cakes, soup stocks, compressed facial packs and garden compost
material. Refer to the 
Fresh Juice Recipes & Menu Planner
for
juice recipes, pulp recipes, sample...

Clean Your
Juicer
Thoroughly
Before Retiring
For The DayPLEASE NOTE:CLEANING YOUR JUICER
10 •Unplug from outlet before assembling or removing parts and before
cleaning.
Do not immerse the Motor Base in water or spray it with water. Clean
only by wiping with a damp sponge, cloth, or paper towel. Use any
liquid dishwashing detergent but do not use any products containing
ammonia or scouring powders. These products will dull, scratch or
mar the plastic surface.•All parts (except the Motor Base) are washable...

9
ASSEMBLY INSTRUCTIONS  
(Continued)
Step FourPlace the  Juicer Cover on over
the Juice Bowl with the large pulp
ejection opening towards the back
of the Juicer. Swing the Clamps
upward as shown in the
illustration.Step FivePlace the tops of the Clamps
on the respective slots on the
Juicer Cover, leaving the
Clamp Hinges resting out.
Press the bottom of the
Clamps in, until they snap
snugly into place.Step SixPlace the Pulp Basket behind
the Juicer under the Pulp Spout
(located on the back of the
Juicer...

8
Step OnePlace Juice Bowl on top of the Motor Base.
The Juice Spout fits over the front of the
Juicer.  Two tabs located on the underside of
the Juice Bowl should rest in the two
complimentary slots on top of the Motor Base.
The tabs and slots are located by each Clamp.
See illustration.Step TwoSet the Blade Basket on the Motor Hub in the
center of the Juice Bowl, and press down on the
outer rim until it feels snug.Step ThreeGently rotate the Blade Basket to ensure that it
turns freely. If initially it...

8
Step OnePlace Juice Bowl on top of the Motor Base.
The Juice Spout fits over the front of the
Juicer.  Two tabs located on the underside of
the Juice Bowl should rest in the two
complimentary slots on top of the Motor Base.
The tabs and slots are located by each Clamp.
See illustration.Step TwoSet the Blade Basket on the Motor Hub in the
center of the Juice Bowl, and press down on the
outer rim until it feels snug.Step ThreeGently rotate the Blade Basket to ensure that it
turns freely. If initially it...

9
ASSEMBLY INSTRUCTIONS  
(Continued)
Step FourPlace the  Juicer Cover on over
the Juice Bowl with the large pulp
ejection opening towards the back
of the Juicer. Swing the Clamps
upward as shown in the
illustration.Step FivePlace the tops of the Clamps
on the respective slots on the
Juicer Cover, leaving the
Clamp Hinges resting out.
Press the bottom of the
Clamps in, until they snap
snugly into place.Step SixPlace the Pulp Basket behind
the Juicer under the Pulp Spout
(located on the back of the
Juicer...