JBL Wem1 Manual

JBL®ON AIR
WEM-1
OWNER’S GUIDE
English
0053CSK - JBL OnAir WEM-1 ENG v6:34199_Control_2_4G_Eng  22/08/08  14:27\
  Side 1 

2
IMPORTANT SAFETY
INSTRUCTIONS
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no...

Wireless Transmitter
Wireless Receiver
3
THANK YOU FOR CHOOSING 
A JBL®PRODUCT
For more than 60 years, JBL has been involved in every aspect of
music and film recording and reproduction, from live performances 
to the recordings you play in your home, car or office.
We’re confident that the JBL system you have chosen will provide
every note of enjoyment that you expected   – and that when you think
about purchasing additional audio equipment for your home, car or
office, you will once again choose JBL....

4
WARNING: The minimum load impedance that this
system can handle safely is 4 Ohms. Using lower
impedance loads can damage the unit and will void
your warranty.
Notes: For the sake of simplicity, throughout this manual we have
used the term “source” when describing connections and operation.
This would apply to any device such as an A/V receiver, audio
component, computer or portable music player.
The JBL On Air WEM-1 may be connected to your source in several
ways. First, determine how you would like to...

5
English
Step 3.
Connect the speaker wire to the push terminals on the receiver
module 
and the terminals on the rear of your speakers, as shown in Figure
4. Please note that the speaker wire features a polarity indicator to
help distinguish its two conductors. Use this polarity indicator to
ensure that you are connecting the positive (+) terminal on one
speaker to the positive (+) terminal on the other, and the negative (–)
to the negative (–).
Figure 4.
Step 4.
Plug the transmitter module  and...

6
Auto On/Standby
The JBL On Air WEM-1 will automatically enter       Standby mode after
approximately 10 minutes when no signal is detected from your
system. The WEM-1 will then power ON instantly when a signal is
detected.When Mute \b is engaged, auto turn-off is deactivated. 
LED Color Transmitter Module Receiver Module
GreenTransmitter and receiver module Transmitter and receiver 
module
are communicating (RF lock) are communicating (RF 
lock)
Blinking Green Transmitter and receiver are Transmitter...

7
English
Push small tab
toward battery slot. Pull battery
drawer out. Insert new battery
with “+” side up, and slide battery drawer back into remote.
Declaration of Conformity
We, Harman Consumer Group, Inc.
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product
described in this owner’s manual is in compliance
with technical standards:
EN 55013:2001+A1:2003 
EN 55020:2002+A1:2003 
EN 61000-3-2:2000 
EN 61000-3-3:1995+A1:2001
EN 60065:2002
Laurent Rault
Harman...

JBL and Control Series are trademarks of Harman International Industries\
, Incorporated, 
registered in the United States and/or other countries. Pro Sound Comes \
Home are trademark
of Harman International Industries, Incorporated.
®PRO SOUND COMES HOME™
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797, USA
8500 Balboa Boulevard, Northridge, CA 91329, USA
2, route de Tours, 72500 Château du Loir, France
516.255.4JBL (4525) (USA only)   www.jbl.com
© 2008 Harman International...