Home > JBL > Loudspeaker > JBL Studio 5 Manual

JBL Studio 5 Manual

Download as PDF Print this page Share this page

Have a look at the manual JBL Studio 5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 57 JBL manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

$Page 5 5www.jb\f.com English St\bdio 530 – S\bRRo\bNd CHANNELS (5.1-CHANNEL SyStEm) When you use Studio 530 speakers as surround-channel speakers in a 5.1-channel system\f place them slightly behind the listening position\f facing each other. Ideally\f they should be 3 – 4 feet (0.9m – 1.2m) above the floor. An alternate location would be on a wall behind the listening position\f facing forward. The surround speakers should not call attention to themselves while they’re playing. Experiment with their...$

$Page 6 6 St\bdio 530 – S\bRRo\bNd CHANNELS (7.1-CHANNEL SyStEm) When you use Studio 530 speakers as surround-channel speakers in a 7.1-channel system\f place the surround side speakers directly to the sides of the listening position\f at least 3 – 4 feet (0.9m – 1.2m) above the floor. Place the surround back speakers on the wall behind the listening position\f also at least 3 – 4 feet (0.9m – 1.2m) above the floor and 3 – 6 feet (0.9m – 1.8m) apart. St\bdio 590/580/ 570/530 Fro\ft Left Speaker St\bdio 530...$

$Page 7 7www.jb\f.com English REmoviNG St\bdio 520C GRiLLES To remove the Studio 520C grilles\f use the provided grille removal tool to pull the grilles away from the enclosure as shown\f then remove them the rest of the way by hand. Use Tool to P\bll Grilles\iAway from Cabi\fet AttACHiNG tHE HoRN CovERS If you remove the speakers’ grilles\f attach the provided horn covers as shown. Make sure that both rubber bumpers on the horn cover fit into the holes in the speaker. Fit Tab i\fto Slot Fit B\bmpers i\fto...$

$Page 8 8 The Studio 5 series speakers’ gold-plated speaker connectors can accept a variety of wire connector types: bare wire\f pin connectors\f spade connectors and banana connectors. \bSiNG BARE WiRE oR piN CoNNECtoRS: 1.2. 3. \bSiNG SpAdE CoNNECtoRS: 1.2. 3. \bSiNG BANANA CoNNECtoRS: 1.2. 3.4.$

$Page 9 9www.jb\f.com English BASiC SiNGLE-WiRE CoNNECtioN To connect the speakers using a single wire\f connect the amplifier to each speaker as shown in the illustration below. You can use either set of connectors on the connector panel. impoRtAN t: d o not remove the meta\f jumper bars from between the two sets of connectors when connecting the speaker wires. + – Use Either Set of Co\f\fectors Do Not Remove J\bmper Bars Receiver or Amplifier (O\fe Cha\f\fel Show\f) Speaker Co\f\fector Pa\fel$

$Page 10 10 Bi-WiRE CoNNECtioN All Studio 5 series speaker connector panels have two sets of input connectors that are joined by metal jumper bars. The upper set of connectors is for the compression-driver/horn assembly\f and the lower set of connectors is for the woofer(s). This arrangement allows you to bi-wire the speakers using a single stereo amplifier or using two stereo amplifiers. Bi-wiring can offer performance advantages and more flexibility in power-amplifier selection over a conventional...$

$Page 11 11www.jb\f.com English usin\b the POrt tuBe inserts (all MOdels exCePt studiO 520C) If\f due to speaker placement or your room's acoustics\f you feel that the speakers produce a bit too much bass output for your taste\f you can use the provided port tube inserts to slightly reduce the speakers' output in the 50Hz – 100Hz region. Insert the port tube insert about half way into the port tube opening as shown in the illustration. Be careful not to push the insert through the port tube and into...$

$Page 12 12 sPeCiFiCatiOns St\bdio 590 FLooRStANdiNG SpEAkER Speaker type: 2-1/2-way dual-woofer\f floorstanding Low-frequency transducer: Two 8" (200mm) PolyPlas™ cones with Symmetrical Field Geometry™ magnet structures\f cast frames and rubber surrounds\f magnetically shielded High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-piece Teonex \b diaphragm on a glass-filled ABS Bi-Radial\b horn\f magnetically shielded Recommended amplifier power: 250 watts Frequency...$

$Page 13 13www.jb\f.com English St\bdio 570 FLooRStANdiNG SpEAkER Speaker type: 2-way dual-woofer\f floorstanding Low-frequency transducer: Two 5-1/4" (130mm) PolyPlas cones with Symmetrical Field Geometry™ magnet structures\f cast frames and rubber surrounds\f magnetically shielded High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-piece Teonex \b diaphragm on a glass-filled ABS Bi-Radial\b horn\f magnetically shielded Recommended amplifier power: 150 watts...$

$Page 14 14 St\bdio 520C CENtER-CHANNEL SpEAkER Speaker type: 2-way dual-woofer\f center-channel Low-frequency transducer: Two 4" (100mm) PolyPlas cones with Symmetrical Field Geometry™ magnet structures\f cast frames and rubber surrounds\f magnetically shielded High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one- piece Teonex \b diaphragm on a glass-filled ABS Bi-Radial\b horn\f magnetically shielded Recommended amplifier power: 150 watts Frequency response: 60Hz –...$

$Page 15 15www.jb\f.com English © 2011 HARMAN International Industries\f Incorporated. All rights reserved. JBL and Bi-Radial are trademarks of HARMAN International Industries\f Incorporated\f registered in the United States and/or other countries. PolyPlas and Symmetrical Field Geometry are trademarks of HARMAN International Industries\f Incorporated. Teonex is a registered trademark of DuPont Tenjin Films. Features\f specifications and appearance are subject to change without notice.HARMAN Consumer\f Inc....$

View all the pages

Add page 11 to Favourites

image text

Enable zoom

							11www.jb\f.com
English
usin\b the POrt tuBe inserts (all MOdels exCePt studiO 520C)
If\f due to speaker placement or your room's acoustics\f you feel that the speakers produce a bit too much bass output 
for your taste\f you can use the provided port tube inserts to slightly reduce the speakers' output in the 50Hz – 100Hz 
region.
Insert the port tube insert about half way into the port tube opening as shown in the illustration. Be careful not to push 
the insert through the port tube and into the speaker cabinet.
Not E: The Studio 590 has two port tubes and includes two port tube inserts.
Carin\b FOr YOur sPea\fers
•     Wipe the cabinet with a clean\f dry cloth to remove dust. Damp cloth may dull the cabinet’s finish. Do not use 
volatile liquids such as benzene\f paint thinner or alcohol on the cabinet.
•      Do not spray insecticide near the cabinet.
•     
To remove dust from the grille fabric\f use a vacuum cleaner set to low suction. 
•     
Never apply suction or pressurized air to the horn opening.
•     
Do not wash the grilles in water\f as it may fade the color or make it uneven.
•     
If the surfaces of the woofer cones become dusty\f you can carefully sweep them clean with a soft\f dry calligraphy 
brush or paint brush. Do not use a damp cloth.

Add page 12 to Favourites

image text

Enable zoom

							12
sPeCiFiCatiOns
St\bdio 590 FLooRStANdiNG SpEAkER
Speaker type: 2-1/2-way dual-woofer\f floorstanding
Low-frequency transducer: Two 8" (200mm) PolyPlas™ cones with Symmetrical Field Geometry™ 
magnet structures\f cast frames and rubber surrounds\f magnetically 
shielded
High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-piece 
Teonex
\b diaphragm on a glass-filled ABS Bi-Radial\b horn\f magnetically 
shielded
Recommended amplifier power: 250 watts
Frequency response: 35Hz – 40kHz (–6dB)
Nominal impedance: 6 ohms
Sensitivity (2.83V/1m): 92dB
Crossover frequencies: 1.5kHz
Enclosure type: Ported
Connector type: Dual gold-plated binding posts (bi-wire capable)
Available finishes: Black or cherry
Dimensions (H x W x D): 49-3/4" x 12-11/16" x 16-1/4" 
 
(1263mm x 322mm x 413mm)
Weight: 69.5 lb (31.5kg)
St\bdio 580 FLooRStANdiNG SpEAkER
Speaker type: 2-way dual-woofer\f floorstanding
Low-frequency transducer: Two 6-1/2" (165mm) PolyPlas cones with Symmetrical Field Geometry™ 
magnet structures\f cast frames and rubber surrounds\f magnetically 
shielded
High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-piece 
Teonex
\b diaphragm on a glass-filled ABS Bi-Radial\b horn\f magnetically 
shielded
Recommended amplifier power: 200 watts
Frequency response: 40Hz – 40kHz (–6dB)
Nominal impedance: 6 ohms
Sensitivity (2.83V/1m): 90dB
Crossover frequencies: 1.5kHz
Enclosure type: Ported
Connector type: Dual gold-plated binding posts (bi-wire capable)
Available finishes: Black or cherry
Dimensions (H x W x D): 42-1/16" x 9-7/8" x 13-3/4" 
 
(1069mm x 250mm x 348mm)
Weight: 49 lb (22.2kg)

Add page 13 to Favourites

image text

Enable zoom

							13www.jb\f.com
English
St\bdio 570 FLooRStANdiNG SpEAkER
Speaker type: 2-way dual-woofer\f floorstanding
Low-frequency transducer: Two 5-1/4" (130mm) PolyPlas cones with Symmetrical Field Geometry™ 
magnet structures\f cast frames and rubber surrounds\f magnetically 
shielded
High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-piece 
Teonex
\b diaphragm on a glass-filled ABS Bi-Radial\b horn\f magnetically 
shielded
Recommended amplifier power: 150 watts
Frequency response: 45Hz – 40kHz (–6dB)
Nominal impedance: 6 ohms
Sensitivity (2.83V/1m): 88dB
Crossover frequencies: 1.5kHz
Enclosure type: Ported
Connector type: Dual gold-plated binding posts (bi-wire capable)
Available finishes: Black or cherry
Dimensions (H x W x D): 34-1/16" x 8-7/16" x 11-3/16" 
 
(896mm x 214mm x 284mm)
Weight: 34.4 lb (15.6kg)
St\bdio 530 BookSHELF SpEAkER
Speaker type:  2-way bookshelf
Low-frequency transducer: 5-1/4" (130mm) PolyPlas cone with Symmetrical Field Geometry™ 
magnet structure\f cast frame and rubber surround\f magnetically 
shielded
High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-
piece Teonex
\b diaphragm on a glass-filled ABS Bi-Radial\b horn\f 
magnetically shielded
Recommended amplifier power: 125 watts
Frequency response: 45Hz – 40kHz (–6dB)
Nominal impedance: 6 ohms
Sensitivity (2.83V/1m): 86dB
Crossover frequencies: 1.5kHz
Enclosure type: Ported
Connector type: Dual gold-plated binding posts (bi-wire capable)
Available finishes: Black or cherry
Dimensions (H x W x D): 18-3/8" x 8-7/16" x 8-3/4" 
 
(467mm x 214mm x 222mm)
Weight: 17 lb (7.7kg)

Add page 14 to Favourites

image text

Enable zoom

							14
St\bdio 520C CENtER-CHANNEL SpEAkER
Speaker type: 2-way dual-woofer\f center-channel
Low-frequency transducer: Two 4" (100mm) PolyPlas cones with Symmetrical Field Geometry™ 
magnet structures\f cast frames and rubber surrounds\f magnetically 
shielded
High-frequency transducer: 1" (25mm) compression driver with neodymium magnet and one-
piece Teonex
\b diaphragm on a glass-filled ABS Bi-Radial\b horn\f 
magnetically shielded
Recommended amplifier power: 150 watts
Frequency response: 60Hz – 40kHz (–6dB)
Nominal impedance: 6 ohms
Sensitivity (2.83V/1m): 88dB
Crossover frequencies: 1.5kHz
Enclosure type: Ported
Connector type: Dual gold-plated binding posts (bi-wire capable)
Available finishes: Black or cherry
Dimensions (H x W x D): 6-3/4" x 21-7/8" x 6-5/8" 
 
(172mm x 555mm x 168mm)
Weight: 16.6 lb (7.5kg)

Add page 15 to Favourites

image text

Enable zoom

							15www.jb\f.com
English
© 2011 HARMAN International Industries\f Incorporated. All rights reserved. 
JBL and Bi-Radial are trademarks of HARMAN International Industries\f Incorporated\f 
registered in the United States and/or other countries.
PolyPlas and Symmetrical Field Geometry are trademarks of HARMAN International Industries\f Incorporated.
Teonex is a registered trademark of DuPont Tenjin Films.
Features\f specifications and appearance are subject to change without notice.HARMAN Consumer\f Inc. 
8500 Balboa Boulevard\f Northridge\f CA 91329 USA
 www.jbl.com

All JBL manuals Comments (0)

Related Manuals for JBL Studio 5 Manual

JBL Control 1 Manual
7 pages | JBL Loudspeaker