JBL Dcr600 2 Manual

							21
Component Video Outputs:If your TV or
video projector has component video inputs,
you may connect these output jacks to the set
for the highest video quality available. Note
that the component video inputs may be
labeled as Y/Pr/Pb or Y/Cr/Cb but, for connec-
tion purposes, they are the same. The outputs
of these jacks should NOT be connected to a
standard composite video input.
S-Video Output:Connect this jack to the
S-Video input on a television or video projector,
or to an S-Video input on an A/V receiver or
processor if you are using that type of device
for S-Video input switching.
Composite Video Output:Connect this
jack to the video input on a television or video
projector, or to a video input on an A/V receiver
or processor if you are using that type of
device for video input switching.
Coaxial Digital Output:Connect this jack
to the coaxial digital input of an A/V receiver
or surround processor for Dolby Digital, DTS or
PCM audio playback. 
NOTE:The coaxial digital output should only
be connected to a digital input. Even though it
is the same RCA-type connector as standard
analog audio connections, DO NOT connect it
to a conventional analog input jack.
Remote Control Output:Connect this
jack to the infrared (IR) input jack of another
JBL (or other compatible) remote-controlled
product to have the built-in 
Remote Sensor
on the DVD600IIprovide IR signals to
other compatible products.
Remote Control Input:Connect the out-
put of a remote infrared sensor, or the remote
control output of another JBL (or other compat-
ible) product, to this jack. This will enable theremote control to operate even when the front
panel 
Remote Sensor is blocked. This
jack may also be used with compatible IR
remote control-based automation systems.
AC Power Cord:Connect this plug to 
an AC outlet. If the outlet is controlled by a
switch, make certain that it is in the ON 
position.
DVD600IIRear Panel Connections 
						

							22
Remote Control Functions
IMPORTANT NOTE:The remote control for
the JBL Cinema ProPack 600
IImay be pro-
grammed to control up to eight devices, includ-
ing the DCR600
IIand DVD600II. It is helpful to
think of the remote as being organized into
“pages,” with one page for each device.
Depending on which device has been selected,
the buttons on that device’s page will perform
different functions, as listed starting on the
next page. These functions may vary from the
labels on the remote, and from one device to
the next.  Some buttons may perform no func-
tion at all for a given device.
In order to go to the page for a particular
device, such as the DVD600
II, you will need to
press the Input Selector button for that device
(DVD in this case), located in a grouping just
below the power buttons. The remote will then
function as if it were dedicated to the DVD600
II.
If you would like to make an adjustment that
affects the DCR600
IIreceiver, such as turning
the volume up or down, you must first go to
the page for the DCR600
IIby pressing its Input
Selector button. This button is labeled “Main”
on the remote. The exception to this rule is
that the transport functions of the DVD600
II–
Play, Forward and Reverse Search, Stop,
Pause, and Previous and Next Chapter/Track
Skip – may be accessed from the “Main” page,
without having to jump to the DVD page.
-        -
PROGRAM
INDICATOR LEDaPower Off Button:Turns off the power
to a device selected by pressing its Input
Selector.
bPower On Button:Turns on the power 
to a device selected by pressing its Input
Selector.
cMute Button:Press to momentarily
silence the DCR600
IIor TV set being con-
trolled, depending on which device has been
selected.
When the remote is being programmed to
operate an external device, such as a CD
player
, this button is pressed, together with
the Input Selector button for the new device,
to begin the programming process.
dDVD Input Selector:Pressing this 
button will perform three actions: 1) If the
DCR600
IIis not turned on, it will power up. 
2) It will select DVD as the input source. 
3) It will switch to the page for the DVD600
II,
which will cause the remote to operate only
the DVD changer. Press the 
Main Buttonh
to return the remote to control of the DCR600II
receiver. 
						

							23
eStatus Button: This button operates only
when the DVD600
IIhas been selected. When a
disc is playing, pressing this button will display
the Status Banner, which contains information
about the disc and enables you to change the
functions.
fgM1 and M2 Macro Buttons/Open-
Close Button:
Press these buttons to store or
recall a “Macro”, which is a preprogrammed
sequence of commands stored in the remote.
When the DVD600
IIhas been selected, the M1
Button
ffunctions to open or close the disc
tray drawer. (
M2ghas no function.) If the
drawer is opened while a disc is still playing,
playback will continue and discs not in use
may be changed. If the drawer is opened while
the unit is stopped, the disc that was playing
will be presented at the front-center position
of the tray.
hMain Input Selector:Pressing this 
button will perform two actions: 1) If the
DCR600
IIis not turned on, it will power up. 
2) It will switch to the page for the DCR600
II,
which will cause the remote to operate only
the receiver and the transport functions of 
the DVD600
II.
iCD Input Selector:Pressing this button
will perform three actions: 1) If the DCR600
IIis
not turned on, it will power up. 2) It will select
CD as the input source. 3) It will switch to the
page for the CD player whose codes have been
programmed into the remote, which will cause
the remote to operate only the CD player. Press
the 
Main Button hto return the remote to
control of the DCR600
IIreceiver.
jTape Input Selector:Pressing this 
button will perform three actions: 1) If the
DCR600
IIis not turned on, it will power up. 
2) It will select TAPE as the input source. 
3) It will switch to the page for the tape deck
whose codes have been programmed into the
remote, which will cause the remote to oper-
ate only the tape deck. Press the 
Main Button
hto return the remote to control of the
DCR600
IIreceiver.
kAM/FM Tuner:Selects the receiver’s
tuner as the listening choice. Pressing this but-
ton when the tuner is already in use will select
between the AM and FM bands.
lVideo 1 Input Selector (VCR 1):Press-
ing this button will perform three actions: 1) If
the DCR600
IIis not turned on, it will power up.
2) It will select VIDEO 1 as the input source. 3)
It will switch to the page for the video device
whose codes have been programmed into theremote, which will cause the remote to oper-
ate only that video device. You may find it con-
venient to connect your VCR to the Video 1
input, since it is the only video source that also
features outputs for recording. Press the 
Main
Button
hto return the remote to control of
the DCR600
IIreceiver.
mVideo 2 Input Selector (VCR 2):Press-
ing this button will perform three actions: 1) If
the DCR600
IIis not turned on, it will power up.
2) It will select VIDEO 2 as the input source. 3)
It will switch to the page for the video device
whose codes have been programmed into the
remote, which will cause the remote to oper-
ate only that video device. You may find it con-
venient to connect a video cassette player to
the Video 2 input. Press the 
Main Buttonh
to return the remote to control of the DCR600II
receiver.
nVideo 3 Input Selector (Cable or
Satellite): 
Pressing this button will perform
three actions: 1) If the DCR600
IIis not turned
on, it will power up. 2) It will select Video 3
(the front panel input) as the input source. 
3) It will switch to the page for the video
device whose codes have been programmed
into the remote, which will cause the remote
to operate only that device. You may find it
convenient to connect your cable television box
or satellite receiver to this input. Since it is
located on the front panel of the receiver, you
may also wish to use this input to temporarily
connect a portable camcorder or video game to
your system. Press the 
Main Buttonhto
return the remote to control of the DCR600
II
receiver.
oTV Input Selector:Pressing this button
will perform three actions: 1) If the DCR600
IIis
not turned on, it will power up. 2) It will select
TV as the input source. 3) It will switch to the
page for the television whose codes have been
programmed into the remote, which will cause
the remote to operate only that device. You
may find it convenient to connect your televi-
sion to this input, particularly since it does not
have a video input associated with it, the
assumption being that the program signal orig-
inates at the TV, and that the TV is already dis-
playing the video portion of the signal. Press
the 
Main Buttonhto return the remote to
control of the DCR600
IIreceiver.
pSleep:Places the DCR600IIin the Sleep
Timer mode. After the time shown in the 
display has elapsed, the DCR600
IIwill auto-
matically go into Standby. Each press of this
button changes the time until turn-off in inter-
vals of 10 minutes, starting with a maximum 
of 90 minutes.This button is also used to change channels on
your TV when the TV is selected.
This button is also used during the “Auto Search”
procedure when programming the remote.
qTest:Begins the sequence used to 
calibrate the speaker output levels.
When the CD input has been selected and a CD
recorder is in use, this button is used to select
among the analog and digital inputs to the CDR.
r6CH (TV/VID):Press to select the 
6-Channel Direct Input∞as the input
source. When used with a compatibly pro-
grammed VCR, DVD, TV or Satellite receiver
that has a “TV/Video” function, pressing this
button will switch between the output of that
device and the external video input to that
device. Consult the owner’s manual for your
specific player or satellite receiver for the
details of how it implements this function.
sVolume Up:Use to raise the system
volume.
tSurround Mode/Audio:Begins the
process of changing the surround mode when
the DCR600
IIis selected. After the button has
been pressed, use the ⁄/¤Buttonsy
to select the desired surround mode.  
When the DVD600
IIis selected, this button
allows you to select from the available audio
tracks (including audio surround modes) or lan-
guages on a DVD disc that is currently playing.
Press this button repeatedly until the desired
audio selection appears.
This button is also used to tune channels when
the TV is selected.
This button is also used during the “Auto
Search” procedure when programming the
remote.
uAll Off:This feature of the JBL One-Click™
(patent pending) remote simultaneously sends
Power Off commands to all programmed
devices controlled by the remote.
vAll On:This feature of the JBL One-Click
remote simultaneously sends Power On com-
mands to all programmed devices controlled by
the remote.
wVolume Down:Use to lower the system
volume.
xChannel/Title/Guide:Starts the process
of setting the receiver’s speaker output levels
using an input source rather than the test tone.
Press this button, then use the 
⁄/¤Buttons 
						

							24
yto select the channel being adjusted,
followed by the 
Set Button. You may 
then use the ⁄/¤Buttons yagain to
change the level for that channel. Press the
Set Buttonto lock in the setting.
When using the DVD600
IIto play a DVD disc,
this button functions as a Title button, and dis-
plays the disc’s Title Select Menu, or a symbol
(

) if the disc either does not offer this func-
tion or has only one title.
When the Video 3 input has been programmed
for a cable or satellite service, this button will
access the service’s programming guide, if the
service is active.
y⁄:Used to change or scroll through items
in the on-screen menus, or to change configu-
ration settings, such as output levels. When
changing an item such as the surround mode
or digital input directly, first press the function
or mode to be changed, such as Surround
Mode or Digital Input, and then press this button
to scroll through the list of available choices. 
In
DVD mode, press this button to skip to the
next higher chapter of the current disc.
zMenu:Used only with video sources.
When DVD is selected, pressing this button
while a DVD disc is playing stops playback and
displays the disc’s menu. When the unit is
stopped, pressing this button displays the DVD
player’s Setup Menu. 
`‹:Used to change the menu selection 
or setting during some of the setup or other
procedures. In DVD mode, press this button to
play the current disc in Fast Reverse mode.
Set:Used to enter settings into the mem-
ory of the DCR600
II, DVD600IIor video device
selected. Also used in the setup procedures for
delay time, speaker configuration and channel
output level adjustment. When the DVD600
II
has been selected, pressing this button will
select the item that is highlighted in the Status
Banner, or in the on-screen menu displayed by
a DVD disc. When the Status Banner has not
been activated, pressing this button will alter-
nately Play or Pause the current disc. When
the On Screen Library is displayed on-screen,
pressing this button will begin play of the 
currently selected disc. 
›:Used to change the menu selection 
or setting during some of the setup or other
procedures. In DVD mode, press this button to
play the current disc in Fast Forward mode.
Digital/Subtitle/Exit:When the DCR600II
is selected, press this button to assign one ofthe digital inputs to a source. When the
DVD600
IIis selected, this button is used to
change the subtitle choice. For other video
devices, it exits the menu.
¤:Used to change or scroll through
items in the on-screen menus, or to change
configuration settings, such as output levels.
When changing an item such as the surround
mode or digital input directly, first press the
function or mode to be changed, such as 
Surround Mode or Digital Input, and then 
press this button to scroll through the list of 
available choices. In DVD mode, press this but-
ton once to return to the beginning of the cur-
rent chapter or track, and twice to skip to the
next lower chapter or track of the current disc.
Delay/Return/Prev Ch.:Begins the
process for setting the delay times used by the
DCR600
IIwhen processing surround sound.
After pressing this button, the delay times are
entered by pressing the 
Set Buttonand
then using the ⁄/¤Buttonsyto
change the setting. Press the 
Set Button
again to complete the process.
This button is also used when viewing a menu
display from a DVD disc. Press it to return to
the previous menu screen.
When the 
Video 3 Input#$has been pro-
grammed for a cable or satellite service, this
button will skip to the previous channel.
–
,
Numeric Keys:These
buttons serve as a ten-button numeric keypad
to enter tuner preset positions. They are also
used with the DVD600
IIto directly access a
disc (when pressed within 3 seconds after the
Disc Skip Button) or track (when
pressed while a disc is playing), to enter data
for sequential programming, to enter or change
the access password for parental control, to
enter a language code, or to respond to menu
options presented by a disc. When the TV or
another video device is selected, they are used
to select channel numbers. They may also be
used to select track or chapter numbers when
playing a CD or DVD.
Tuner Mode/Angle:Press this button
when the tuner is in use to select between
automatic tuning and manual tuning. When 
the button is pressed so that the 
AUTO
Indicator
Tgoes out, pressing the Tuning
Buttons
8will move the frequency
up or down in single-step increments. When
the 
AUTO Indicator T Tis lit, pressing the
Tuning Buttons 8 8will cause the
tuner to search for the next station with an
acceptable signal. When the FM band is in
use, pressing this button when a station’s sig-nal is weak will change to monaural reception. 
When a DVD encoded with multiple-angle
information is playing, press to change the
angle in use. This function is only available 
on discs that are specially prepared to take
advantage of the multiple-angle function, and
only for those parts of the disc that are recorded
with multiple-angle content. The DVD600IIwill
display a camera icon on the screen to indicate
when this feature is available.
Memory:Enters a radio station into the
DCR600II’s preset memory. Once the MEMORY
IndicatorQflashes, you have five seconds
to enter a preset memory location using the
Numeric Keys–
,. Repeat
the process to enter additional stations.
Tuning Up/Down/Step (Frame
Advance) Buttons:
When the tuner is in use,
these buttons will tune up or down through the
selected frequency band. If the 
Tuner Mode
Button
@has been pressed so that the
AUTO IndicatorTis illuminated, pressing
either of the buttons will cause the tuner to
seek the next station with acceptable signal
strength for quality reception. When the 
AUTO
Indicator
Tis NOT illuminated, pressing
these buttons will tune stations in single-step
increments.
When a DVD disc is playing, press these 
buttons to move forward or backward one
frame at a time. Press the 
Play/Pause Button
to resume normal play. These 
buttons do not function when a CD is playing.
Direct/Program Button:Pressing this
button in tuner mode, or while a CD or DVD is
playing, starts the sequence for direct entry of
a station’s frequency, a CD track or a DVD chap-
ter. After pressing the button, simply press the
proper 
Numeric Keys–
,to
select a station, track or chapter. You may also
skip to a track or chapter by entering its number,
without first pressing the 
Direct Button.
When the DVD600IIis stopped, press this 
button to display the program menu and enter
a programmed play sequence. When a disc is
playing, press to switch between normal play
and programmed playback, if a playlist has
been programmed.
Clear Button:Erases incorrect entries
when using the remote to directly enter a radio
station’s frequency.
When the DVD600
IIhas been selected, press
this button to remove the Status Banner or
other displays from your video screen. This
button is also used to clear items from 
programmed playlists. 
						

							25
Preset Up/Down/Slow-Play
Buttons:
When the tuner is in use, press these
buttons to scroll through the stations pro-
grammed into the receiver’s memory.  
When a DVD disc is playing and the DVD600
II
has been selected, press these buttons to
move forward or backward through the disc in
slow speed. Each press of these buttons
changes the slow-play speed in the following
order: 1/16 Normal Speed 
➔1/8 Normal
Speed 
➔1/4 Normal Speed ➔1/2 Normal
Speed. To resume normal play, press the
Play/Pause Button. These buttons
do not function when a CD is playing.
Night Mode/Random:Activates the
Night mode of the DCR600
II. This mode is
available in specially encoded digital sources,
and it preserves dialogue (center channel)
intelligibility at low volume levels.
When the DVD600
IIhas been selected, press
to begin the playback of all tracks on a disc in
random order.
Disc Skip Button:Press twice in rapid
succession to move to the next available disc
in the tray when using a DVD or CD player.
This button has no direct effect on the
DCR600
II. When a single press of this button is
followed by a disc number, the DVD600
IIwill
skip directly to that disc.
Check:This button only functions when
the DVD600
IIhas been selected. When a CD is
playing, press this button to check the status
of the current disc via the on-screen display.
This button is also used to verify the contents
of a programmed playlist via the front-panel
Information Display.
Subtitle On/Off:This button only 
functions when the DVD600
IIhas been selected.
When a DVD is playing, press this button to
turn the Subtitle Display on or off.
Repeat:This button only functions when
the DVD600
IIor a CD player has been selected.
Press to select one of the Repeat-Play modes:
Repeat All (discs), Repeat 1 Disc, Repeat Title,
Repeat Track/Chapter. Each press of the 
button shows the choice selected in both the
on-screen Status Banner display or in the
Repeat Indicators in the front panel
Information Display.
Repeat A–B:This button only functions
when the DVD600
IIhas been selected. Press
once to begin the selection of a portion of a
disc to be repeated. Press it again to choose
the end point of the repeat-play selection. This
function is unavailable during programmed or
random play.
NOTE:When any of the following buttons–is pressed while the remote has
selected the Main Page, the remote will 
automatically switch to control of the DVD, as
indicated by the 
DVD Input Selectord
lighting.
Reverse Search/Rewind:When the
DVD600
IIhas been selected, press to move
backward through a CD or DVD at one of four
speeds. Each press and release will increase
the search speed, in the following order: R.
Search x 2 
➔R. Search x 4 ➔R. Search x 8
➔R. Search x 16. Once you have selected the
desired speed, release the button, and the 
disc will continue to search at fast speed. 
To resume normal playback, press the 
Play/
Pause Button
.
When a tape deck or VCR has been selected,
this button rewinds the tape.
Play Button:Press to begin playback
when the DVD600
IIhas been selected. If the
disc tray drawer is open, it will automatically
close when the button is pushed. Pressing the
Play button when the unit is in the Standby
mode will turn the unit on and begin playback
of the last disc in use.
When a CD player, tape deck or VCR has been
selected, pressing this button will also begin
playback. See the owner’s manual for that
device for more information on the operation
of the play function as it affects that device.
Forward Search/Fast Forward:When 
the DVD600
IIhas been selected, press to move 
forward through a CD or DVD at one of four
speeds. Each press and release will increase
the search speed, in the following order: 
F. Search x 2 
➔ F. Search x 4 ➔F. Search 
x 8 
➔F. Search x 16.  Once you have selected
the desired speed, release the button, and the
disc will continue to search at fast speed. To
resume normal playback, press the 
Play/
Pause Button
. When a tape deck 
or VCR has been selected, this button fast-for-
wards the tape.
Record Button:This button only func-
tions when a CD/CD-R, tape deck or VCR con-
nected to the Video 1 input has been selected.
See the owner’s manual for that device for fur-
ther information on how to make recordings.
Stop Button:This button has no effect
on the DCR600
II. When the DVD600IIhas been
selected, press this button once to place the
disc in the Resume mode. Playback will stop,
and as long as the tray is not opened or the
disc changed, DVD playback will continue 
from the same point on the disc when the
Play/Pause Buttonis pressed
again, even if the unit has been turned off inthe interim. To stop a disc without entering
Resume mode, press the Stop button twice.
This button also performs the Stop function
when a CD player, tape deck or VCR connected
to the Video 1 input has been selected.
Pause Button:Press to pause the disc in
use. To resume playback, either press the
Pause button again, or press the 
Play/Pause
Button
.
Previous/Next:Press to move 
backward or forward through the music tracks
on a CD disc or the chapters on a DVD disc.
This button also scans backward or forward
when a VCR connected to the Video 1 input
has been selected.
On Screen Library™ (patent pending):
This feature lists the titles and disc types of all
discs currently loaded in the DVD600
IIon your
video screen. The On Screen Library resets
automatically every time the DVD600
II’s disc
tray is opened. When the tray is closed, the On
Screen Library will need to read and identify
all five discs, a process which will take approx-
imately one minute. You may interrupt this
process by pressing the 
Stop Button  .
The On Screen Library will resume the process
of identifying the discs when you press the 
On
Screen Library Button 
. You may also
prevent the On Screen Library from reading
and identifying the discs by closing the tray
with a press of one of the 
Direct Access
Buttons ,
which will begin play of that
numbered disc.
If you have not opened the disc tray since the
last time the On Screen Library was accessed,
and if the current disc is stopped, you may
press this button to display the On Screen
Library, even if you have not selected DVD as
the input source on the DCR600
II. While in
DVD mode, use the ⁄/¤Buttonsyto
scroll through the list. Press the 
Set Button
to play the selected disc. Do not press a
Numeric Key–
,while the
On Screen Library is displayed, as it will
remove the display without skipping to a 
different disc.
Program Indicator LED:Lights while 
programming the remote with device codes,
macros, punch-through functions and device
reassignments, or while resetting the remote
memory. 
						

							26
Remote Control Function Grid
MAIN
DVD CD/CD-R Tape VCR 1 (VID 1) VCR 2 (VID 2) CBL (VID 3) SAT (VID 3) TV#ButtonDCR600II+DVD600II
01 POWER OFF Power Off Power Off Power Off Power Off Power Off Power Off Power Off Power Off
02 POWER ON Power On Power On Power On Power On Power On Power On Power On Power On
03 MUTE Mute
04 DVD DVD Input Select DVD  Select DVD  Select DVD  Select DVD  Select DVD  Select DVD  Select DVD  Select DVD  Select
05 STATUS STATUS
06 M1 M1 Open/Close Open/Close Cancel Cancel PPV Cancel Sleep
07 M2 M2 Repeat FAV FAV
08 MAIN DCR Select DCR Select DCR Select DCR Select DCR Select DCR Select DCR Select DCR Select DCR Select
09 CD CD Input Select CD Select CD Select CD Select CD Select CD Select CD Select CD Select CD Select
10 TAPE Tape Input Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select Tape Select
11 AM/FM Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select Tuner Select
12 VID1 Video 1 Select Video 1 Select Video 1 Select Video 1 Select Video 1 Select Video 1 Select Video 1 Select Video 1 Select Video 1 Select
13 VID2 Video 2 Select Video 2 Select Video 2 Select Video 2 Select Video 2 Select Video 2 Select Video 2 Select Video 2 Select Video 2 Select
14 VID3 Video 3 Select Video 3 Select Video 3 Select Video 3 Select Video 3 Select Video 3 Select Video 3 Select Video 3 Select Video 3 Select
15 TV TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select TV Select
16 Sleep Sleep Channel+ Channel+ Channel+ Channel+ Channel+
17 Test Test Tone Input Select
18 6 CH6-Channel Direct Input SelectTV/DVD CDP Select TV/VCR TV/VCR TV/Cable TV/Sat TV/VCR
19 Volume UP Volume Up Volume Up Input Level Up Volume Up Volume Up Volume Up Volume Up Volume Up
20 Surround SelectSurround Mode SelectAudio CDR Select Channel–- Channel– Channel–- Channel– Channel–
21 ALL OFF Sends OFF Commands Simultaneously for ALL 8 Devices
22 ALL ON Sends ON Commands Simultaneously for ALL 8 Devices
23 Volume Down Volume Down Volume Down Input Level Down Volume Down Volume Down Volume Down Volume Down Volume Down
24 Channel/Guide Channel Trim TitleInfo/Guide Info/Guide
25 Up Move/Adjust Up Up, Chapter + Track + Up Up Up Up Up
26 Menu Menu Menu Menu Menu Menu Menu
27 Left Move/Adjust Left Left, Fast Search Fast Search Left Left Left Left Left
28 Set Set Enter, Play/Pause Play/Pause Enter Enter Enter Enter Enter
29 Right Move/Adjust Right Right, Fast Search Fast Search Right Right Right Right Right
30 Digital/Exit Digital Input Select Subtitle Exit Exit Exit Exit Exit
31 Down Move/Adjust Down Down, Chapter – Track– Down Down Down Down Down
32 Delay/Prev. Ch. Delay Adjust Return Time Prev. Channel Prev. Channel Prev. Channel
33 1 1 1 1 1 1 1 1 1
34 2 2 2 2 2 2 2 2 2
35 3 3 3 3 3 3 3 3 3
36 4 4 4 4 4 4 4 4 4
D
e
v
i
c
e 
						

							27
Remote Control Function Grid
#MAIN DVD CD/CD-R Tape VCR 1 (VID 1) VCR 2 (VID 2) CBL (VID 3) SAT (VID 3) TV
37 5 5 5 5 5 5 5 5 5
38 6 6 6 6 6 6 6 6 6
39 7 7 7 7 7 7 7 7 7
40 8 8 8 8 8 8 8 8 8
41 Tun-M Tuner Mode Angle Select Random Play Bypass Next
42 9 9 9 9 9 9 9 9 9
43 0 0 0 0 0 0 0 0 0
44 Memory Memory
45 Tuning Up Tune Up Step +Day+ Day+
46 Direct Direct Tuner EntryProgram, Chapter DirectTrack Direct
47 Clear Clear Clear Clear Clear Clear Clear Clear Clear
48 Preset Up Preset Tune Up Slow Forward (+10) Page+ Page+
49 Tuning Down Tune Down Step– Track Increment Day– Day–
50 Night Night Mode Select Random
51 D. Skip Disc Skip Disc Skip Disc Skip
52 Preset Down Preset Tune Down Slow Reverse Intro Scan Page– Page–
53 CHECK Check
54 Subtitle On/Off Subtitle On/Off
55 REPEAT Repeat Repeat
56 A–B A–B
57‹‹REW (DVD) R. Search R. Search Rewind Rewind
58 PLAY (
‹›)PLAY (DVD) Play PlayF. Play
Play PlayR. Play
59››FF (DVD) F. Search F. Search Fast Fwd. Fast Fwd. Fast Fwd.
60 RECORD Record Record Record
61 STOP STOP (DVD) Stop Stop Stop Stop Stop
62 PAUSE PAUSE (DVD) Pause Pause Pause Pause Pause
63 PREV. PREV. CHAP (DVD) Prev. Skip– Scan– Scan–
64 NEXT NEXT CHAP (DVD) Next  Skip+ Scan+ Scan+
65 On Screen On Screen On Screen On Screen On Screen On Screen On Screen On Screen On Screen On Screen
Library Library Library Library Library Library Library Library Library Library
D
e
v
i
c
e
Button 
						

							28
Remote Control Code Tables
TV
Maker (Brand) Name Setup Code Number
A-MARK 103 132 
ADMIRAL 192
AKAI 123 160
AMPRO 164
ANAM 045 103 106 109 112 122
AOC 103 123 128
BLAUPUNKT 084
BROKSONIC 205 206
CANDLE 123 128
CAPEHART 059
CENTURION 123 171
CETRONIC 045
CITIZEN 045 123 128 132
CLASSIC 045
CONCERTO 128
CONTEC 045
CORANDO 172
CORONADO 132
CRAIG 045 157 158 159
CROWN 045 132
CURTIS MATHES 123  128  132
CXC 045
DAEWOO 045 087 102 105 106 108 111 114 116 119 127 128 132
DAYTRON 128 132
CIGI LINK 200
DYNASTY 045
DYNATECH 063
ELECTROHOME 115 132
EMERSON 045 123 128 132 139 157 158 159 162 205
FUNAI 045
FUTURETECH 045
GE 087 121 123 128 133 145 159 163
GOLDSTAR 101 103 110 128 132
GRUNDIG 193
HALL MARK 128
HARMAN KARDON 201
HITACHI 123 128 132 144 147
INFINITY 148
INKEL 120
JBL 148
JC PENNEY 115  123  128  132  145
JENSEN 019
JVC 079 087 134
KAWASHO 173
KEC 045
KENWOOD 123 204
KMC 132
KTV 045 123 132 162
LLOYTRON 172 173
LODGENET 069 
LOGIK 069
LUXMAN 128
LXI 077 145 148
MAGNAVOX 123 128 132 145 148
MARANTZ 115 123 148
MATSUI 148
MEMOREX 069 128
METZ 084 
						

							29
Remote Control Code Tables
TV
Maker (Brand) Name Setup Code Number
MGA 115 123 128
MINERVA 084
MITSUBISHI 077 115 123 128 160 167 168
MTC 175 176
NATIONAL 148 177 179 180 181 182
NEC 115 121 123 125
NIKEI 045 
ONKING 045
ONWA 045
OPTONICA 077
ORION 207 208 209 210 211
PANASONIC 087 148 169
PHILCO 045 115 123 128 132 148
PHILIPS 123 128 132 145 148
PIONEER 024 123 128 213 214
PORTLAND 128 132
PROSCAN 133
PROTON 059 122 128 132 165
QUASAR 087
RADIO SHACK 045  128  132  180  196  197
RCA 115 123 128 133 145 161 163
REALISTIC 045 196 167
RUNCO 152 153
SAA 183
SAMPO 059 123 128
SAMSUNG 124 128 132 145
SANYO 054
SCOTT 045 128 132
SEARS 128 132 145
SHARP 077 128 132
SIEMENS 084
SIGNATURE 069
SONY 117 130 136 194 212
SOUNDESIGN 045 128
SPECTRICON 103
SSS 011 045
SYLVANIA 123 128 145 148
SYMPHONIC 184
TANDY 077
TATUNG 063
TECHNICS 080
TECHWOOD 128
TEKNIKA 045 069 115 123 128 132
TELERENT 069
TERA 156
THOMSON 190 191
TMK 128
TOSHIBA 063 129 202
TOTEVISION 132
VIDEO CONCEPTS 160
VIDTECH 128
WARDS 069 128 132 148
YAMAHA 123 128
YORK 128
YUPITERU 045
ZENITH 069 090
ZONDA 103 
						

							30
Remote Control Code Tables
VCR
Maker (Brand) Name Setup Code Number
AIWA 040
AKAI 048 108 109 126
AMPRO 076
AMSTRAD 133
ASA 134
AUDIO DYNAMICS 018  048
BROKSONIC 110 147 166
CANDLE 134 135 140
CANON 135 140
CAPEHART 094
CITIZEN 134 140
CRAIG 094
DAEWOO 134
DAYTRON 045 116
DBX 017 094 104 105
DUAL 094
DYNATECH 018 048
ELECTROHOME 136
EMERSON 040
FERGUSON 131
FINLUX 013 040 042 105 110 112 119 134 143
FISHER 136
FUNAI 133
GE 017 142
GO VIDEO 113  117
GOLDSTAR 018 107 134
GRAETZ 136
HARMAN KARDON 018  049
HITACHI 040 048 118 130
ITT 136
JC PENNEY 018  045  134
JENSEN 048
JVC 018 048 111  130  132
KENWOOD 020 048
LLOYD 040
LXI 020 040 134
MAGIN 045
MAGNAVOX 040
MARANTZ 018
MARTA 134
MATSUI 036
MEMOREX 017 020 040  076  115 120 134
MGA 049 131 
MITSUBISHI 049 131 145 146
MTC 133
MULTITECH 040
NAD 139
NATIONAL 140
NEC 018 048