InFocus ScreenPlay 7205 Projector User Manual

							10
Adjust the zoom or focus rings by rotating them until the desired image size 
and sharpness are produced.
If the image is not square, adjust the keystone using the buttons on the key-
pad. Press the upper Ke y s t o n e  button to reduce the width of the upper por-
tion of the image, and press the lower Ke y s t o n e  button to reduce the width 
of the lower portion.
You can also adjust the horizontal and vertical keystone via the Picture 
menu. See page 24
The Contrast, Brightness, Color, and Tint are factory calibrated to D65 col-
ors, but you can adjust these settings in the Picture menu if necessary. 
See page 23 for help with the menus.
The focus ring is threaded, similar to a 35mm camera lens. To put a filter on 
your lens, simply screw it clockwise onto the threaded focus ring.
adjust zoom and focus
focus
zoom
adjust keystone
adjust Picture menuadd a lens filter 
						

							11
Connecting a computerConnect either a VESA cable or M1 cable into the appropriate connector on 
the projector. Connect the other end to the video port on your computer. If 
you are using a desktop computer, you first need to disconnect the monitor 
cable from the computer ’s video port. 
Connect the power cable to the connector on the back of the projector and to 
your electrical outlet.
The Power LED on the projector ’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector. 
Turn on the projector, then your computer.
You can control the projector from an LCD control panel or computer by 
connecting an RS-232 cable to the projector ’s Serial connector. Specific 
RS-232 commands can be found in the Appendix starting on page 38 and in 
the Service and Support section of our website at www.infocushome.com/
support.
IR in1
2 YY
Pr Pr Pb Pbserial control M1-DA
vesatrigger 1
8
2 1
34
6 57
trigger 2
components-videovideoD5
component
connect computer cable
IR in1
2 YY
Pr Pr Pb Pbserial control M1-DA
vesatrigger 1
8
2 1
34
6 57
trigger 2
components-videovideoD5
component
 connect power cable
IR in1
2 YY
Pr Pr Pb Pbserial control M1-DA
vesatrigger 1
8
2 1
34
6 57
trigger 2
components-videovideoD5
component
connect RS-232 cable
IR in1
2 YY
Pr Pr Pb Pbserial control M1-DA
vesatrigger 1
8
2 1
34
6 57
trigger 2
components-videovideoD5
component 
						

							12
Shutting down the projectorPowe r  S av e
The projector has a Power Save feature in the System menu that automati-
cally turns the lamp off after no signals are detected for 20 minutes. After 10 
additional minutes with no signal, the projector powers down. If an active 
signal is received before the projector powers down, the image is displayed. 
You must press the Pow e r button to display an image after 30 minutes have 
passed. 
Turning off the projector
To turn off the projector, press the Pow e r button. The lamp turns off and the 
LED blinks green for about one minute while the fans continue to run to 
cool the lamp. When the lamp has cooled, the LED lights green and the fans 
stop. Unplug the power cable to completely power off the projector.
Troubleshooting your setupIf your image appears correctly on the screen, skip to the next section 
(page 20). If it does not, troubleshoot the setup. 
The LED on top of the projector ’s keypad indicates the state of the projector 
and can help you troubleshoot. 
 
The following table shows some potential problems. In some cases, more 
than one possible solution is provided. Try the solutions in the order they 
are presented. When the problem is solved, you can skip the additional 
solutions.
Table 2: LED behavior and meaning
LED color/behavior
Meaning
solid green The projector is plugged in, or the projec-
tor has been turned on and the software 
has initialized. The projector has been 
turned off and the fans have stopped.
blinking green The Pow e r button has been pressed and 
the software is initializing, or the projec-
tor is powering down and the fans are 
running to cool the lamp.
blinking red
The projector will not start up if the LED 
is blinking red. You must correct the prob-
lem, disconnect and reconnect the power 
cable, then power on the projector. 
See page 34 for more information on 
blinking red LEDs.A fan (blinks 4 times) or lamp (blinks 3 
times) failure has occurred. Turn off the 
projector and wait one minute, then turn 
the projector on again. Also check for a 
blocked vent or a stopped fan (blinks 5 
times).
solid red An unidentifiable error: please contact 
Technical Support. 
						

							13
Problem Solution Result
No startup screenPlug power cable in and remove lens cap
press Power button
Correct image
Image not centered on screenMove projector, adjust zoom, adjust heightCorrect image
ScreenPlay
Adjust horizontal or vertical position in 
Picture>Keystone menuzoom 
						

							14
Image not squareAdjust keystone on keypad or Keystone 
menuSquare image
Image does not fit 16:9 screenChange aspect ratio to 16:9 in 
Picture>Aspect ratio menuCorrect image
Edges of image distortedTurn Overscan on in the Picture>Overscan 
menu
Correct image
AB
AB 
						

							15
1. Projected colors don’t match source
2. Colors are washed out or too deep
3. Image from component source appears greenish1. Adjust color, tint, color temperature, 
brightness, or contrast in the menus.
2. Pick another gamma setting
3. Pick another color space
Correct image
Image upside downTurn off Ceiling in Settings>System menuCorrect image
Image reversed left to right
Turn off Rear in Settings>System menu
Correct image 
COLOR
COLOR
A
B
AB
A
AB 
						

							16
Video image “torn” and fragmentedChange Video Standard in 
Picture>Advanced menuCorrect image
Lamp won’t turn on, LED blinking red (page 12)Make sure vents aren’t blocked; allow 
projector to cool for one minute Unplug projector; wait one minute; plug in 
projector and turn it on: lamp lights
A
AB
B
AB
blinksred
 
ScreenPlay 
						

							17
Computer-specific troubleshooting
Only startup screen appearsPress the Source button 
Activate laptop’s external portComputer image projected
No computer image, just the words “Signal out of 
range” Adjust computer refresh rate in Control 
Panel>Display>Settings>Advanced>
Adapter (location varies by operating 
system)Computer image projected
A
ScreenPlay
or restart
laptop
A
A
A
Signal out of
range
A
A 
						

							18
Image fuzzy or cropped Set your computer’s display resolution to 
the native resolution of the projector 
(Start>Settings>Control 
Panel>Display>Settings tab, select 
1280x720) Image clear and not cropped
The video embedded in my PowerPoint 
presentation does not play on the screenTurn off the internal LCD display on your 
laptopEmbedded video plays correctly
A
AA
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
A
A
B
AB
A
B 
						

							19 Still having problems?
If you need assistance, visit our website or call us. See the inside of the back 
cover for support contact information. 
This product is backed by a limited warranty. An extended warranty plan 
may be purchased from your dealer. When sending the projector in for 
repair, we recommend shipping the unit in its original packing material, or 
having a professional packaging company pack the unit. An optional ATA 
shipping case is available for purchase that provides adequate protection 
for shipping. Please insure your shipment for its full value.