InFocus ScreenPla 5700 Projector User Manual

							21
Using the menusTo open the menus, press the menu button on the keypad or remote. (The 
menus automatically close after 60 seconds if no buttons are pressed.) The 
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button. 
To change a menu setting, highlight it, press Select, then use the up and 
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm 
your changes. Use the arrows to navigate to another setting. When your 
adjustments are complete, navigate to Exit, then press Select to navigate to 
the previous menu; press the Menu button at any time to close the menus. 
Dots appear before the menu name. The number of dots indicate the menu’s 
level, ranging from one (the Main menu) to four (the most nested menus). 
The menus are grouped by usage:
 The Picture menu provides image adjustments.
 The Settings menu provides set-up type adjustments that are not 
changed often.
 The About menu provides a read-only display of information about the 
projector and source. 
Certain menu items may be hidden until a particular source is connected. 
For example, Tint is only available for NTSC video sources and will be hid-
den when other sources are active. Other menu items may be grayed out 
when they are not available. For example, Brightness is grayed out until an 
image is active.
Keypad navigation 
buttons
Main menuMenu
button
 
 
Picture menuSettings menu Dots
About menu 
						

							22
Picture menuTo adjust the following five settings, highlight the setting, press Select, use 
the up and down arrows to adjust the values, then press select to confirm 
the changes. All menu defaults are listed in a table starting on page 37.
Key s t o n e: adjusts the image vertically and makes a squarer image. You can 
also adjust keystone from the keypad.
Contrast: controls the degree of difference between the lightest and darkest 
parts of the picture and changes the amount of black and white in the 
image.
Brightness: changes the intensity of the image. You can also adjust bright-
ness from the keypad.
Color: (video sources only) adjusts a video image from black and white to 
fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the 
image.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. 
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 
1.78:1, or 16:9. You can choose Native, 4:3, 16:9, Letterbox, or Natural Wide. 
The default is 16:9. The goal is to show the most detail on the screen while 
preserving the ratio of width to height. The native resolution of the projec-
tor is 1024x576. Use Native, 4:3 or Naural Wide for 4:3 input sources; use 
Native, 16:9 or Letterbox for 16:9 input. Pressing the Resize button on the 
remote cycles through these options.
Native: this mode bypasses the internal scaler, displaying the image 
with no resizing. 
Since the native resolution is 1024x576 and 4x3 video images are 
approximately 640x480, 4x3 images will always be smaller than the dis-
play and will be centered in the display.  Computer images 1024x768 or 
smaller will also be centered in the display.  If a 16x9 video source or a 
1280x1024 or larger computer source is viewed, it will display up to 
1024 pixels and 576 lines from the center of the input.
increasing keystone
decreasing keystone
Aspect ratio 
						

							23
16:9: the default is 16:9, which preserves the 16:9 aspect ratio and is 
designed to be used with content that is Enhanced for Widescreen TVs. 
4:3: resizes the image from its original version to fit a standard 4:3 
aspect ratio screen. If you have a 4:3 source on a 16:9 screen, the image 
is placed in a 16:9 space, so black bars appear at the sides of the image.
Letterbox: preserves the 16:9 aspect ratio. If you have a 16:9 source and 
screen, the image fills the screen. If your source is letterboxed, the 
image expanded to fill the screen.
Natural Wide: this mode stretches a 4:3 image to fill the entire 16:9 
screen. The center two-thirds of the image is unchanged; the edges of 
the image are stretched. 
16
16 99 16:9 image input16:9 image 
16:9
aspect ratio16 9
4 34:3 image input 4:3 image on 16:9 screen
black bars
black bars
4:3 aspect ratio
16 9 letterbox image input
16:9 image fills 16:9 screen
black bars
black bars
4 3 letterbox
aspect ratio
4:3 image fills 16:9 screen
natural wide
aspect ratio4:3 image input
4 3
16 9 
						

							24
Presets: This allows you to customize settings and save the settings to be 
restored later. To restore the factory default settings, choose Factory Reset in 
the Settings>Service menu. 
To set a preset for the current source, adjust the image, select Save Settings 
in the Presets menu, then choose Save User 1, 2, or 3. You can recall these 
settings in the future by selecting the appropriate user presets. 
Gamma: Gamma tables contain preset intensity configurations optimized 
for the input source. You can select a gamma table that has been specifically 
tuned for either film, video, Bright Room, or PC input. (Film input is mate-
rial originally captured on a film camera, like a movie; video input is mate-
rial originally captured on a video camera, like a TV show or sporting 
event.) White Peaking increases the brightness of whites that are near 100%.
NOTE: Your viewing preferences may vary. Cycle through the gamma 
options and pick the one you like the best.
Overscan: lets you crop the input or zoom the input if desired.
Save User Presets Presets
Gamma
Overscan 
						

							25 Advanced settings
The following 4 options are for computer or HDTV sources only. 
Phase: adjusts the phase of the video signal’s digital conversion.
Tr a c k i n g: adjusts the frequency of the video signal’s digital conversion. 
Horizontal/Vertical Position: adjusts the position of the source.
Tr u e L i f e: This option refers to Faroudja’s TrueLife processing of the image. 
All standard definition interlaced video signals (composite, S-video and 
component) are routed through this processor.  Extended and High Defini-
tion progressive component sources are not routed though this processor by 
default.  You can turn TrueLife on to route these signals through the proces-
sor and then adjust the following 3 options:
Chroma Detail: This adjusts the color sharpness.
Luma Detail: This adjusts the sharpness. 
Chroma Delay: aligns the Luma and Chroma Detail
CCS: (Cross Color Suppression) processes the signal to remove any color 
information from the luma portion of the signal. It is On for all composite 
signals, and can be turned off for S-video and inter-laced component sig-
nals.
Film Mode: controls deinterlacing. 2:2/3:2 Enable If selected, the deinter-
lacer attempt to perform 3:2 pulldown, assuming the source was originally 
created on 24fps film.  If the original source is 30fps film, you should select 
NTSC 2:2 pulldown.
Noise Reduction: adjusts signal noise reduction. Choose Off to have no 
noise reduction, choose Auto to have the software determine the amount of 
noise reduction, or choose Manual and adjust the Level. 
Skintone Bypass prevents the noise reduction processing from being 
applied to skin tones. Images of people often look better with less process-
ing. Available when Auto or Manual are selected.
Advanced
True LifeFilm Mode
Noise reduction 
						

							26
Color Space: This option applies to computer and HDTV sources (it won’t 
appear in the menu for video sources). It allows you to select a color space 
that has been specifically tuned for the video input. When Auto is selected, 
the projector automatically determines the standard. To choose a different 
setting, turn off Auto, then choose RGB for computer sources, choose 
REC709 for component 1080i or 720p sources, or choose REC601 for compo-
nent 480p or 576p sources.
Color Temperature: changes the intensity of the colors. Select a listed 
value.
Color Control: allows you to individually adjust the gain (relative warmth 
of the color) and the offset (the amount of black in the color) of the red, 
green, and blue colors. 
Video Standard: When it is set to Auto, the projector attempts to pick the 
video standard automatically based on the input signal it receives. (The 
video standard options may vary depending on your region of the world.) If 
the projector is unable to detect the correct standard, the colors may not 
look right or the image may appear “torn.” If this happens, manually select 
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu.
Color Space
Color Temperature
Color ControlVideo Standard 
						

							27
Settings menuSources
: allows you to assign a particular input to a specific source key on 
the remote and enables or disables Autosource. When Autosource is not 
checked, the projector defaults to the last-used source. If no source is found, 
a blank screen displays. When Autosource is checked, the projector checks 
the last-used source first at power up. If no signal is present, the projector 
checks the sources in order until a source is found or until power down. 
You can use the Source Enable feature to eliminate certain sources from this 
search, which will speed the search. By default, the check boxes for all 
sources are checked. Uncheck a source’s box to eliminate it from the search.
System
All options in this menu toggle between on and off.
Rear: reverses the image so you can project from behind a translucent 
screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
NOTE: It is recommended that all final image adjustments in Ceiling mode 
are made once the unit has fully warmed up (approximately 20 minutes).
Auto Power: When Auto Power is checked, the projector automatically 
goes into the startup state after the projector receives power. This allows 
control of ceiling mounted projectors with a wall power switch.
Display Messages: displays status messages (such as “Searching”) in the 
lower-left corner of the screen.
High Power: Turn this on to increase the light output of the lamp. This also 
shortens lamp life and increases fan noise.
Sources
Settings menu
Source Enable
Source 1
System menu 
						

							28
Tr a n s l u c e n t  O S D: makes the menus translucent. This prevents the image 
from being completely covered by the menus while you are making image 
adjustments.
Chime: turn this on to hear a sound when the Powe r button is pressed.
Sleep Timer: allows you to force the projector to automatically shutoff after 
4 hours.
Pow e r  S av e: when On, the lamp is automatically turned off after no signals 
are detected for 20 minutes. After 10 additional minutes with no signal, the 
projector powers down. If an active signal is received before the projector 
powers down, the image will be displayed. 
Startup Logo: allows you to display a blank Black, White, or Blue screen 
instead of the default screen at startup and when no source is active or 
detected. 
Blank Screen: determines what color displays when you press the Blank 
button on the remote or when no source is detected.
Language: allows you to select a language for the onscreen display of 
menus and messages.
System menu
Startup logo
Blank ScreenLanguage 
						

							29
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours) to their default 
after displaying a confirmation dialog box.
Te s t  P a t t e r n: displays a test pattern when the Blank button on the remote is 
pressed. To select the patterns, use the up/down arrows on the remote or 
keypad.
Blue Only: turns off the Red and Green portions of the input, allowing you 
to properly adjust the color balance with a SMPTE color bar pattern.
Color Wheel Index: makes the hue of various gray levels consistent. 
ADC Calibration: allows adjustment of the calibrated ADC values so that 
color accuracy can be optimized. Adjust the slidebars for each value and 
note the change in the appropriate color.  Use a component input when 
adjusting the Component controls.
Service Code: only used by authorized service personnel.MaintenanceCleaning the lens1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you 
don’t intend to use the projector immediately, replace the lens cap.
Service menu
clean the lens 
with a soft dry cloth
and non-abrasive
cleaner 
						

							30
Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the 
lamp has been in use. After 1980 hours, the message “Change lamp” briefly 
appears on the screen at each startup. To maintain optimal video perfor-
mance, we recommend changing the lamp after 2000 hours, depending on 
usage. You can order new lamp modules from your dealer. See “Accesso-
ries” on page 32 for information.1
Turn off the projector and unplug the power cable. 
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside down and remove the lamp door by removing 
the two screws and sliding the lamp door tabs out of the three tab bays.
CAUTION: Never operate the projector with the lamp door removed. 
This disrupts the air flow and causes the projector to overheat.
4
Loosen the captive screw on the lamp module.
Lamp hours used
turn off and unplug
the projector
wait 60 minutesloosen the screw on lamp module
bail wire