Home > InFocus > Projector > InFocus Projector X16 User Manual

InFocus Projector X16 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual InFocus Projector X16 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 493 InFocus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Positioning your projector 11
    How to determine the position of the projector 
    for a given screen size
    1. Select your screen size.
    2. Refer to the table and find the closest match to your screen size in the left 
    columns labelled 4:3 screen diagonal. Using this value, look across this row 
    to the right to find the corresponding average distance from screen value in 
    the column labelled Average. This is the projection distance.
    3. On that same row, look across to the right column and make note of the 
    Vertical offset in mm value. This will determine the final vertical offset 
    placement of the projector in relation to the edge of the screen.
    4. The recommended position for the projector is aligned perpendicular to the 
    horizontal center of the screen, at the distance from the screen determined in 
    step 2 above, and offset by the value determined in step 3 above.
    For example, if you are using a 108-inch screen, the average projection distance is 
    4362 mm and with a vertical offset of 165 mm.
    If you place the projector in a different position (to that recommended), you will 
    have to tilt it down or up to center the image on the screen. In these situations, 
    some image distortion will occur. Use the Keystone function to correct the 
    distortion. See Correcting keystone on page 25 for details.
    How to determine the recommended screen size 
    for a given distance
    This method can be used for situations where you have purchased this projector 
    and would like to know what screen size will fit in your room.
    The maximum screen size is limited by the physical space available in your room. 
    1. Measure the distance between the projector and where you want to position 
    the screen. This is the projection distance.
    2. Refer to the table and find the closest match to your measurement in the 
    average distance from screen column labelled Average. If the min and max 
    values are available on the table, check that your measured distance is 
    between the min and max distances listed on either side of the average 
    distance value.
    3. Using this value, look across that row to the left to find the corresponding 
    screen diagonal listed in that row. That is the projected image size of the 
    projector at that projection distance.
    4. On that same row, look across to the right column and make note of the 
    Vertical offset in mm value. This will determine the final placement of the 
    screen in relation to the horizontal plane of the projector. 
    For example, if your measured projection distance was 4.5 m (4500 mm), the 
    closest match in the Average column is 4362 mm. Looking across this row shows 
    that a 108-inch screen is required. 
    						
    							Positioning your projector 12
    Projection dimensions
    Refer to Dimensions on page 52 for the center of lens dimensions of this projector 
    before calculating the appropriate position.
    There is 3% tolerance among these numbers due to optical component variations. InFocus 
    recommends that if you intend to permanently install the projector, you should physically test 
    the projection size and distance using the actual projector in situ before you permanently 
    install it, so as to make allowance for this projectors optical characteristics. This will help you 
    determine the exact mounting position so that it best suits your installation location.
    4:3 screen diagonalRecommended projection distance 
    from screen in mmVertical offset in 
    mm
    FeetInchesmmMin length 
    (with max. 
    zoom)AverageMax length 
    (with min. 
    zoom)
    4 48 1219 1846 1938 2031 73
    59 1500 2271 2385 2498 90
    5 60 1524 2308 2423 2538 91
    6 72 1829 2769 2908 3046 110
    79 2000 3028 3180 3331 120
    7 84 2134 3231 3392 3554 128
    8 96 2438 3692 3877 4062 146
    98 2500 3786 3975 4164 150
    9 108 2743 4154 4362 4569 165
    118 3000 4543 4770 4997 180
    Projection distanceCenter of lens Screen
    Vertical offset Maximum zoom
    Minimum zoom 
    						
    							Connection 13
    Connection
    When connecting a signal source to the projector, be sure to:
    1. Turn all equipment off before making any connections.
    2. Use the correct signal cables for each source.
    3. Ensure the cables are firmly inserted. 
    In the connections shown below, some cables may not be included with the projector (see 
    Shipping contents on page 4). They are commercially available from electronics stores.
    Connecting a computer or monitor
    Connecting a computer
    The projector provides a VGA input socket that allows you to connect it to both 
    IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are 
    connecting legacy version Macintosh computers.
    To connect the projector to a notebook or desktop computer:
    1. Take the supplied VGA cable and connect one end to the D-Sub output 
    socket of the computer.
    2. Connect the other end of the VGA cable to the D-SUB IN signal input socket 
    on the projector.
    3. If you wish to make use of the projector (mixed mono) speaker in your 
    presentations, take a suitable audio cable and connect one end of the cable to 
    the audio output socket of the device, and the other end to the AUDIO socket 
    of the projector. 
    Once connected, the audio can be controlled by the projector On-Screen 
    Display (OSD) menus. See Adjusting the sound on page 34 for details.
    The final connection path should be like that shown in the following diagram:
    Many notebooks do not turn on their external video ports when connected to a projector. 
    Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a 
    function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press 
    FN and the labeled function key simultaneously. Refer to your notebooks documentation to 
    find your notebooks key combination.
    Notebook or desktop computer
    Audio 
    cable VGA cable 
    						
    							Connection 14
    Connecting a monitor
    If you want to view your presentation close-up on a monitor as well as on the 
    screen, you can connect the D-SUB OUT signal output socket on the projector to 
    an external monitor with a VGA cable following the instructions below:
    To connect the projector to a monitor:
    1. Connect the projector to a computer as described in Connecting a computer 
    on page 13.
    2. Take a suitable VGA cable (only one supplied) and connect one end of the 
    cable to the D-Sub input socket of the video monitor. 
    Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A 
    cable and connect the DVI end of the cable to the DVI input socket of the 
    video monitor.
    3. Connect the other end of the cable to the D-SUB OUT socket on the projector.
    The final connection path should be like that shown in the following diagram:
    • The D-Sub output only works when an appropriate D-Sub input is made to the projector.
    • If you wish to use this connection method when the projector is in standby mode, make 
    sure the VGA Out function is turned on in the SYSTEM SETUP: Advanced menu. See VGA 
    Out on page 41 for details.
    Notebook or desktop computer
    VGA cable
    VGA cableVGA to DVI-A 
    cable 
    						
    							Connection 15
    Connecting Video source devices
    You can connect your projector to various Video source devices that provide any 
    one of the following output sockets:
    • Component Video
    • S-Video
    • Video (composite)
    You need only connect the projector to a Video source device using just one of the 
    above connecting methods, however each provides a different level of video 
    quality. The method you choose will most likely depend upon the availability of 
    matching terminals on both the projector and the Video source device as described 
    below:
    Best video quality
    The best available video connection method is Component Video (not to be 
    confused with composite Video). Digital TV tuner and DVD players output 
    Component Video natively, so if available on your devices, this should be your 
    connection method of choice in preference to (composite) Video.
    See Connecting a Component Video source device on page 16 for how to 
    connect the projector to a component video device.
    Better video quality
    The S-Video method provides a better quality analog video than standard 
    composite Video. If you have both composite Video and S-Video output terminals 
    on your Video source device, you should elect to use the S-Video option.
    See Connecting an S-Video source device on page 17 for how to connect the 
    projector to an S-Video device.
    Least video quality
    Composite Video is an analog video and will result in a perfectly acceptable, but 
    less than optimal result from your projector, being the least video quality of the 
    available methods described here.
    See Connecting a composite Video source device on page 18 for how to connect 
    the projector to a composite Video device.
    Connecting audio
    The projector has one built-in mono speaker which is designed to provide basic 
    audio functionality accompanying data presentations for business purposes only. 
    They are not designed for, nor intended for stereo audio reproduction use as might 
    be expected in home theater or home cinema applications. Any stereo audio input 
    (if provided), is mixed into a common mono audio output through the projector 
    speaker. 
    						
    							Connection 16
    Connecting a Component Video source device
    Examine your Video source device to determine if it has a set of unused 
    Component Video output sockets available: 
    • If so, you can continue with this procedure.
    • If not, you will need to reassess which method you can use to connect to the 
    device.
    To connect the projector to a Component Video source device:
    1. Take a Component Video to VGA (D-Sub) adaptor cable and connect the end 
    with 3 RCA type connectors to the Component Video output sockets of the 
    Video source device. Match the color of the plugs to the color of the sockets; 
    green to green, blue to blue, and red to red.
    2. Connect the other end of the Component Video to VGA (D-Sub) adaptor cable 
    (with a D-Sub type connector) to the D-SUB IN socket on the projector.
    3. If you wish to make use of the projector (mixed mono) speaker in your 
    presentations, take a suitable audio cable and connect one end of the cable to 
    the audio output socket of the device, and the other end to the AUDIO socket 
    of the projector. 
    Once connected, the audio can be controlled by the projector On-Screen 
    Display (OSD) menus. See Adjusting the sound on page 34 for details.
    The final connection path should be like that shown in the following diagram:
    • The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
    connected. See Connecting audio on page 15 for details.
    • If the selected video image is not displayed after the projector is turned on and the correct 
    video source has been selected, check that the Video source device is turned on and 
    operating correctly. Also check that the signal cables have been connected correctly.
    AV device
    Component Video to 
    VGA (D-Sub) adaptor 
    cable Audio 
    cable 
    						
    							Connection 17
    Connecting an S-Video source device
    Examine your Video source device to determine if it has an unused S-Video output 
    socket available: 
    • If so, you can continue with this procedure.
    • If not, you will need to reassess which method you can use to connect to the 
    device.
    To connect the projector to an S-Video source device:
    1. Take an S-Video cable and connect one end to the S-Video output socket of 
    the Video source device.
    2. Connect the other end of the S-Video cable to the S-VIDEO socket on the 
    projector.
    3. If you wish to make use of the projector (mixed mono) speaker in your 
    presentations, take a suitable audio cable and connect one end of the cable to 
    the audio output socket of the device, and the other end to the AUDIO socket 
    of the projector. 
    Once connected, the audio can be controlled by the projector On-Screen 
    Display (OSD) menus. See Adjusting the sound on page 34 for details.
    The final connection path should be like that shown in the following diagram:
    • The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
    connected. See Connecting audio on page 15 for details.
    • If the selected video image is not displayed after the projector is turned on and the correct 
    video source has been selected, check that the Video source device is turned on and 
    operating correctly. Also check that the signal cables have been connected correctly.
    • If you have already made a Component Video connection between the projector and this 
    S-Video source device using Component Video connections, you need not connect to this 
    device using an S-Video connection as this makes an unnecessary second connection of 
    poorer picture quality. See Connecting Video source devices on page 15 for details.
    AV device
    S-Video cableAudio cable 
    						
    							Connection 18
    Connecting a composite Video source device
    Examine your Video source device to determine if it has a set of unused composite 
    Video output sockets available:
    • If so, you can continue with this procedure.
    • If not, you will need to reassess which method you can use to connect to the 
    device.
    To connect the projector to a composite Video source device:
    1. Take a Video cable and connect one end to the composite Video output 
    socket of the Video source device.
    2. Connect the other end of the Video cable to the VIDEO socket on the 
    projector.
    3. If you wish to make use of the projector (mixed mono) speaker in your 
    presentations, take a suitable audio cable and connect one end of the cable to 
    the audio output socket of the device, and the other end to the AUDIO socket 
    of the projector. 
    Once connected, the audio can be controlled by the projector On-Screen 
    Display (OSD) menus. See Adjusting the sound on page 34 for details.
    The final connection path should be like that shown in the following diagram:
    • The projector is only capable of playing mixed mono audio, even if a stereo audio input is 
    connected. See Connecting audio on page 15 for details.
    • If the selected video image is not displayed after the projector is turned on and the correct 
    video source has been selected, check that the Video source device is turned on and 
    operating correctly. Also check that the signal cables have been connected correctly.
    • You need only connect to this device using a composite Video connection if Component 
    Video and S-Video inputs are unavailable for use. See Connecting Video source devices 
    on page 15 for details.
    AV device
    Video cable  Audio cable 
    						
    							Operation 19
    Operation
    Starting up the projector
    1. Plug the power cord into the projector and 
    into a wall socket. Turn on the wall socket 
    switch (where fitted). Check that the 
    POWER indicator light on the projector 
    lights orange after power has been applied.
    2. Remove the lens cap. If it is closed, it 
    could become deformed due to the heat 
    produced by the projection lamp.
    3. Press POWER on the projector or 
    remote control to start the projector. The 
    POWER indicator light flashes green and 
    stays green when the projector is on.
    The start up procedure takes about 30 
    seconds. In the later stage of start up, a 
    startup logo is projected.
    (If necessary) Rotate the focus ring to adjust the image clearness.
    • If the projector is still hot from previous activity, it will run the cooling fan for 
    approximately 90 seconds before energizing the lamp. 
    • To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before 
    turning it off.
    4. If you are prompted for a password, press the arrow keys to enter a six-digit 
    password. See Utilizing the password function on page 21 for details.
    5. Switch all of the connected equipment on.
    6. The projector will start to search for input signals. The current input signal 
    being scanned displays in the upper left corner of the screen. If the projector 
    doesnt detect a valid signal, the message No Signal will continue displaying 
    until an input signal is found.
    You can also press SOURCE on the projector or remote control to select your 
    desired input signal. See Switching input signal on page 23 for details.
    If the frequency/resolution of the input signal exceeds the projectors operating range, you will 
    see the message Out of Range displayed on a blank screen. Please change to an input signal 
    which is compatible with the projectors resolution or set the input signal to a lower setting. 
    See Timing chart on page 52 for details.
    II 
    						
    							Operation 20
    Using the menus
    The projector is equipped with On-Screen Display (OSD) menus for making various 
    adjustments and settings.
    Below is the overview of the OSD menu.
    To use the OSD menus, please set them to your familiar language first.
    1. Press MENU/EXIT on the projector or 
    remote control to turn the OSD menu 
    on.3. Press  to highlight 
    Language and press  /  
    to select a preferred 
    language.
    2. Use  /  to highlight the SYSTEM 
    SETUP: Basic menu.4. Press MENU/EXIT twice* on 
    the projector or remote 
    control to leave and save the 
    settings.
    *The first press leads you back to 
    the main menu and the second 
    press closes the OSD menu.
    Current input signal
    Main menu icon
    Main menu
    Sub-menu
    Highlight
    Press MENU/
    EXIT to the 
    previous 
    page or to 
    exit.Status
    DISPLAY
    Wall Color
    Aspect Ratio
    Phase
    H. Size
    Digital ZoomOff
    Auto
    16
    0
    MENU ExitAnalog RGB
    ENTER KeystonePosition
    DISPLAYWall Color
    Aspect Ratio
    Position
    Phase
    H. Size
    Digital ZoomOff
    Auto
    MENU Exit
    Keystone
    16
    0
    Analog RGBSYSTEM SETUP: Basic
    Projector Position
    Auto Power Off
    Blank Timer
    Timer Controller Panel Key Lock
    Splash Screen
    Analog RGB
    MENU Exit
    Front Table
    Disable
    Disable
    Off
    Disable
    InFocus Presentation TimerEnglish Language
    SYSTEM SETUP: Basic
    Projector Position
    Auto Power Off
    Blank Timer
    Timer Controller Panel Key Lock
    Splash Screen
    Analog RGB
    MENU Exit
    Front Table
    Disable
    Disable
    Off
    Disable
    InFocus Presentation Timer
    English Language 
    						
    All InFocus manuals Comments (0)

    Related Manuals for InFocus Projector X16 User Manual