InFocus Projector Work Big In5106 User Manual

							30
Video Standard: when set to Auto, the projector attempts to automatically 
pick the video standard based on the input signal it receives. (The video 
standard options may vary depending on your region of the world.) If the 
projector is unable to detect the correct standard, the colors may not look 
right or the image may appear “torn.” If this happens, manually select a 
video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu. 
Active Iris: when on, the projector monitors the image brightness and mod-
ifies the light output if the image is dark, which improves black levels. In 
Presentation mode, it looks at peak brightness, in Theater mode it looks at 
average brightness.
Overscan: (Computer 1 and video sources only) removes noise around the 
video image.
The following 4 options are for computer sources only: 
Phase: adjusts the horizontal phase of computer 2, 3 and component (except 
480i and 576i) sources. 
Tr a c k i n g: adjusts the horizontal scan of a computer source (except Com-
puter 1).
Horizontal / Vertical Position: adjusts the position of a computer source 
(except Computer 1) and Video 1 source (except 480i and 576i).
Computer 2: allows you to turn Sync on Green on for this source.
Computer 3: allows you to turn Sync on Green on for this source..
Video Standard
Active Iris
Computer 2
Computer 3 
						

							31
Settings menuAudio: allows adjustments to the volume. Also allows you to turn on and 
off the Internal speakers and assign a particular source to a specific audio 
input. If your HDMI source has problems with its audio stream, you can 
mute it by selecting HDMI Noise Cancel. 
Sources
: allows you to assign a particular input to a specific source key 
when using the remote. Also allows selection of a default Startup Source 
and enables or disables Autosource. 
Sources>Power-up Source: this determines which source the projector 
checks first for active signal during power-up. 
Sources>Autosource: When Autosource is not checked, the projector 
defaults to the source selected in Powerup Source. If no source is found, a 
blank screen displays. When Autosource is checked, Powerup Source deter-
mines which source the projector defaults to at power-up. If no signal is 
present, the projector checks the sources in order until a source is found or 
until power down. 
System>Rear: reverses the image so you can project from behind a 
translucent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
WARNING: To prevent eye injury if the projector is ceiling mounted, 
wear protective eyewear before opening lamp door. A warning sticker is 
included with the user documentation. Place this sticker on the lamp 
door if the projector is mounted on the ceiling.
IR Receivers: turns individual IR receivers off or on to avoid environ-
mental interference.
Auto Power: When Auto Power is checked, the projector automatically 
goes into the startup state after the projector is powered on. This allows 
control of ceiling mounted projectors with a wall power switch.
Display Messages: displays status messages (such as “Searching”) in the 
lower-left corner of the screen.
Low Power: toggles between on and off. Turn it on to lower the light out-
put of the lamp. This also lowers the fan speed, making the projector qui-
eter.PC Screen Saver Off: prevents your notebook computer from going into 
Screen Save mode. The projector must be connected to the PC via a USB 
cable for this feature to work. 
Audio Settings
menu
SourcesPowerup 
SourceSystem 
IR Receivers 
						

							32
Pow e r  S av e: automatically turns the lamp off after no signals are 
detected for 20 minutes. After 10 additional minutes with no signal, the 
projector powers down. If an active signal is received before the projec-
tor powers down, the image will be displayed. 
Screen Save: automatically blanks the screen after no signals are 
detected for five minutes. The image returns when an active source is 
detected or a remote or keypad button is pressed. Screen Save is disabled 
when Power Save is enabled.
Startup Logo: allows you to display a blank Black, White, or Blue screen 
instead of the default screen when no source is detected at startup. It also 
allows you to capture and display a custom startup screen. 
To capture a custom logo, display the image you want to capture on your 
computer and select the Capture New option. From the Capture New 
menu, use the Capture Position X and Capture Position Y adjustments to 
frame the logo to be captured. Press Capture Start in the Capture New 
menu. The projector will let you know if the capture was a success or a 
failure.
The next time you start the projector, the custom logo you captured dis-
plays.
Blank Screen: determines what color is displayed when you press the 
Blank button on an optional remote.
Screen Save
Startup Logo
Capture New
Blank Screen 
						

							33
Custom Key (for use with optional remote only): allows you to assign a dif-
ferent function to the Custom key on the optional remote to quickly and 
easily use the effect. Only one effect can be enabled at a time. The default is 
Source Info; highlight an effect and press Select to choose a different one.
Blank: shows an empty screen. 
Mute: turns off all sound. 
AV  M u t e: turns off all sound and displays a blank screen.
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Image: causes all sources to be reacquired.
Freeze: pauses the projected image.
Magnify: allows you to enlarge a section of the projected image.
Source Info: displays the Source Info menu.
Service Info: displays the Service Info menu.
Network: The projector has an RJ45 Ethernet connector that supports net-
work connections and TCP/IP protocols. This will allow for the control and 
management of the projector over a corporate network. Visit our website for 
complete details on using the networking functionality. The following fields 
are accessible when DHCP is not checked and available for manual entry of 
data.
IP Address: Identifies the projector on the network.
Subnet Mask: Separates the network address part of the IP address.
Default Gateway: The IP address of the local router.
DNS Server: Shows the address of the DNS server.
DHCP: Select this to automatically obtain an IP address, Subnet mask, 
and Default gateway.Network Restart: Disconnects the projector from the network, gets a 
new IP address, and reconnects.
Network Info: Provides information on the network configuration.
Custom KeyNetwork
Network
Info 
						

							34
Language: allows you to select a language for the onscreen display of 
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp and Filter Hours and Net-
work settings) to their default after displaying a confirmation dialog box.
Reset Lamp Hours: resets the lamp hours counter in the Service Info menu 
to zero. Do this only after changing the lamp. It displays a confirmation dia-
log box.
Reset Filter Hours: resets the filter counter in the Service Info menu to 
zero. Do this only after cleaning the filter. It displays a confirmation dialog 
box.
Lens Type: change this setting only if you purchase an optional lens. The 
projector customizes its keystone settings based on the lens used. Select 
your optional lens from the menu. A sticker containing a number between 1 
and 5 is attached to the lens to help you identify which type of lens you pur-
chased.
Service Info: provides information for service.
Service Code: only used by authorized service personnel.
Language
Service menuLens Type
Service Info 
						

							35
MaintenanceCleaning the lens1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion. If you 
don’t intend to use the projector immediately, replace the lens cap.
Replacing the clock batteriesThe projector has a lithium Hitachi Maxell battery (part number CR2032) on 
the bottom that is used to power the clock used for networking applications. 
Visit our website for complete details on using the networking functionality.1
Turn off the projector and unplug the power cable. 
2
Wait 45 minutes to allow the projector to cool thoroughly.
3
Turn the projector upside down and use a coin to turn the battery cover 
to the “Open” position.
4
Remove the battery and dispose of in an environmentally proper man-
ner.
5
Install a new battery with the “+” side facing up.
6
Press the battery into place, then replace the battery cover.
NOTE: The clock time will need to be reset in the web browser application 
after replacing the battery. 
clean the lens 
with a soft dry cloth
and non-abrasive
cleaner
turn off and unplug
the projector
wait 45 minutes
120
%.15
open battery cover
close battery cover install new battery, 
+ side up
press battery into position 
						

							36
Replacing the projection lampThe lamp hour timer in the Service Info menu counts the number of hours 
the lamp has been in use. Twenty hours before the specified end of the 
lamp’s life, the message “Change lamp” briefly appears on the projected 
screen. 
NOTE: You can order new lamp housings from www.infocus.com (in select 
areas), your retailer or your dealer. Only genuine InFocus lamps are tested 
for use in this projector. InFocus is not liable for the performance, safety or 
certification of any other lamps. The use of other lamps violates the projec-
tor warranty and voids all certification marks on this projector.1
Turn off the projector and unplug the power cable. 
2
Wait 45 minutes to allow the projector to cool thoroughly.
3
Loosen the lamp cover screw on the right side of the projector (marked 
by the arrow) then slide and lift the lamp cover off.
WARNINGS: 
 To avoid burns, allow the projector to cool for at least 45 minutes before 
you replace the lamp.
 Only genuine InFocus lamps are tested with this projector. Use of other 
lamps may cause electrical shock and fire.
 To prevent eye injury if the projector is ceiling mounted, wear protec-
tive eyewear before opening lamp door. A warning sticker is included 
with the user documentation. Place this sticker on the lamp door if the 
projector is mounted on the ceiling.
 Do not drop the lamp module. The glass may shatter and cause injury. 
Do not touch the glass lamp screen. Fingerprints can obscure projection 
sharpness.
 Be extremely careful when removing the lamp housing. In the unlikely 
event that the bulb ruptures, small glass fragments may be generated. 
The lamp housing is designed to contain these fragments, but use cau-
tion when removing the lamp housing. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands 
after lamp replacement. 
Hg – Lamp contains mercury. Manage in accordance with local 
disposal laws. See www.lamprecycle.org.
lamp hours
turn off and unplug
the projector
wait 45 minuteslamp cover screw 
						

							37 4
Loosen the three captive screws (marked by the arrows) on the lamp 
module. When replacing the lamp, never touch any screws without the 
arrow mark.
5
Carefully remove the lamp module by grasping and lifting the handle. 
Dispose of the lamp in an environmentally proper manner. 
6
Install the new lamp module, making sure that it is properly seated, and 
tighten the three captive screws.
7
Replace the cover over the lamp module by sliding it back into place and 
tightening the screw.
8
Plug in the power cable, press the power switch then press the Pow e r 
button to turn the projector back on. Reset the lamp hour timer by navi-
gating to the Settings>Service menu and selecting Reset Lamp Hours.
loosen the captive screws on lamp module
lamp module handle
reset lamp hours in Service menu 
						

							38
Cleaning the dust filter1
Turn off the projector and unplug the power cable. 
2
Wait 45 minutes to allow the projector to cool thoroughly.
WA R N I N G: To avoid burns, allow the projector to cool for at least 45 
minutes before you clean or replace the dust filter. 
3
Remove the dust filter cover on the side of the projector by pressing up 
on the two tabs at the cover ’s bottom. 
4
Pull the tab on the center of the black dust filter bracket and lift it off.
5
Clean the filter, cover, and vent using a vacuum set on low power. 
Replace the filter if it is damaged or too dirty to clean.
6
Replace the dust filter and the bracket on the cover, then replace the dust 
filter cover.
7
Reset the filter hour timer by navigating to the Settings>Service menu 
and selecting Reset Filter Hours.
Using the security lockThe projector has a security lock for use with a cable lock system. See the 
Accessories catalog that came with the projector, or visit our website, for 
ordering information. Refer to the information that came with the lock for 
instructions on how to use it.
turn off and unplug
the projector
wait 45 minutes
tabs
dust filter cover
reset filter hours in Service menu
 
security lock 
						

							39
AppendixProjected image sizeNOTE: Visit the Service section of our website for interactive image size cal-
culators for the standard and optional lenses.
Table 2: Projection sizes: Standard lens (1.5 - 1.8:1 throw ratio)
The image offset range for the standard lens is 9:1 (90%) to 1:1 (50%). 
Optional lensesWARNING: When replacing the lens, turn off the projector and pull out the 
power cord from the receptacle. Loosen the screws marked with a triangle 
to remove the lens. 
NOTE: You can order optional lenses from www.infocus.com (in select 
areas), your retailer or your dealer.
Table 3: Projection sizes: Short Fixed lens (0.8:1 throw ratio)
Minimum Image Maximum Image
Distance 
(feet/m) Diagonal 
Image
(feet/m)Image 
Width 
(feet/m) Diagonal 
Image
(feet/m)Image 
Width 
(feet/m)
Min Distance
3/0.92.1/0.66 1.7/0.53 2.6/0.79 2.1/0.63
5/1.5 3.5/1.1 2.8/0.86 4.2/1.3 3.4/1.0
10/3.0 7.0/2.1 5.6 1.7 8.3/2.5
15/4.6 10.4/3.2 8.3/2.5 12.5/3.8 10/3
20/6.1 13.8/4.2 11/3.4 16.6/5.1 13.3/4
25/7.6 17.2/7.6 13.8/4.2 20.7/6.3 16.6/5
Max Distance
30/9.120.6/6.3 16.5/5 24.8/7.6 19.8/6.1
Projection Distance 
(inch/m)
Screen Size (inch/m)  Minimum
40/1 24/0.6
60/1.5 35/0.9
70/1.8 43/1.1
100/2.5 63/1.6
120/3 75/1.9
150/3.8 94/2.4
200/5.1 130/3.3
250/6.4 161/4.1
300/7.6 193/4.9
350/8.9 224/5.7