InFocus Projector Work Big In5104 User Manual

InFocus Corporate Headquarters:27500 SW Parkway Avenue Wilsonville, Oregon 97070-9215, USAPhone: 503-685-8888 1-800-294-6400 Fax: 503-685-8887
In EuropeInFocus International B.V.Louis Armstrongweg 1101311 RL Almere, The Netherlands Phone: (31) 36 5392000 Fax: (31) 36 5392999 
In Asia#07-01, Tanglin Shopping Centre19 Tanglin RoadSingapore 247909Phone: (65) 6334-9005Fax: (65) 6333-4525
IN5102/IN5104/IN5106
 User’s Guide
IN5102/IN5104/IN5106 
 Regulatory models W50, W55
User’s Guide
IN5102/IN5104/IN5106...

1
Declaration of ConformityManufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 
97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conform to the following 
directives and norms: 
EMC Directive 2004/108/EC
EMC: EN 55022
           EN 55024
 EN 61000-3-2
 EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 1
st Edition 
TrademarksApple, Macintosh, and PowerBook are...

2
Do not look into laser beam emitted from the front of the remote control
Location of laser beam warning labels on remoteLocation of laser beam warning labels on remote OR this label
Do not look into laser beam emitted from the front of the remote control
Location of laser beam warning labels on remoteLocation of laser beam warning labels on remote OR this label 

3
Table of Contents
Introduction 5
Included Items  5
Positioning the projector  7
Connecting a computer  8
Required computer connections  8
Displaying a computer image  10
Adjusting the image  11
Connecting a video device  12
Displaying a video image  13
Shutting down the projector  15
Troubleshooting your setup  15
Using the keypad buttons  22
Using the remote control  23
Using the audio  24
Optimizing computer images  25
Presentation features  25
Optimizing video images  26
Customizing the projector...

4
Important Operating Considerations for Safety
 Place the projector in a horizontal position no greater than 8 degrees off 
axis.
 Locate the projector in a well-ventilated area without any obstructions 
to intake or exhaust vents. Do not place the projector on a tablecloth or 
other soft covering that may block the vents. 
 Locate the projector at least 4 (1.2 m) away from any heating or cooling 
vents.
 Use only approved ceiling mounts.

Wa r n i n g
: To prevent eye injury if the projector is...

5
IntroductionYour new multimedia projector provides three computer, three video, and 
four audio inputs, one audio output, and RS-232 and Network control. It 
has XGA 1024x768 resolution. Optional user-changeable short, fixed short, 
long and ultra long throw lenses make this a flexible product suitable for 
many different uses. The projector is easy to connect, easy to use, and easy 
to maintain. Product specificationsTo read the latest specifications on your multimedia projector, be sure to 
visit our...

6 Connector Panel
The projector provides three computer and three video connection options: 
 one VESA computer
 one HDMI™ (High Definition Multimedia Interface)*
 one component BNC (G/Y, B/C
B/P
B, R/C
R/P
R, H, V)
 one component RCA video (Pr, Pb, Y)
 one S-video
 one composite RCA video
The projector provides computer and video connectors for audio support:
 
 two composite RCA stereo audio (L, R)
 one audio out
 two audio ins 
The projector also provides the following connectors:
 one wired...

7
Positioning the projectorTo determine where to position the projector, consider the size and shape of 
your screen, the location of your power outlets, and the distance between 
the projector and the rest of your equipment. Here are some general guide-
lines:
 Position the projector on a flat surface at a right angle to the screen. The 
projector (with the standard lens) must be at least 3 feet (0.9m) from the 
projection screen.
 Position the projector within 10 feet (3m) of your power source and...

8
Connecting a computerRequired computer connectionsConnect one end of the VESA computer cable to the Computer 2 connector 
on the projector. Connect the other end to the video port on your computer. 
If you are using a desktop computer, you first need to disconnect the moni-
tor cable from the computer ’s video port. 
Connect the black power cable to the connector on the back of the projector 
and to your electrical outlet.
NOTE: Always use the power cable that shipped with the projector. Optional...

9
If you are using a desktop computer and want to see the image on your 
computer screen as well as on the projection screen, plug the monitor cable 
to the Monitor out connector on the projector. 
You can control the projector from an LCD control panel, touch screen, or 
other control device or computer by connecting an RS-232 cable to the pro-
jector ’s Serial Control connector. Specific RS-232 commands can be found 
in the Service and Support section of our website and in the Appendix.
The projector...