InFocus Projector Work Big In10 User Manual

							
IN10 
Reference Guide 
						

							1
Declaration of ConformityManufacturer: InFocus Corporation, 27500 SW Parkway Avenue, Wilsonville, 
 
Oregon 97070 USA
 
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
 
We declare under our sole responsibility that this projector conforms to the following 
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
 
EMC: EN 55022
 
           EN 55024
 
 EN 61000-3-2
 
 EN 61000-3-3
 
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
 
Safety: IEC 60950-1: 1
st Edition 
 
May, 2004TrademarksMicrosoft, PowerPoint, Word, Excel and Windows are trademarks or registered trade
-
marks of Microsoft Corporation. Digital Light Processing is a trademark or registered 
trademark of Texas Instruments. Adobe and Acrobat are trademarks or registered 
trademarks of Adobe Systems Incorporated. InFocus, In Focus, and INFOCUS (styl
-
ized) are either registered trademarks or trademarks of InFocus Corporation in the 
United States and other countries. FCC WarningThis equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro
-
vide reasonable protection against harmful interference when the equipment is oper
-
ated in a commercial environment. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the instruc
-
tion manual, may cause harmful interference to radio communications. Operation of 
this equipment in a residential area is likely to cause harmful interference in which 
case the user will be required to correct the interference at his own expense. 
 
Changes or modifications not expressly approved by InFocus Corporation may void 
authority to operate the equipment.EN 55022 WarningThis is a Class A product. In a domestic environment it may cause radio interference, 
in which case the user may be required to take adequate measures. The typical use is 
in a conference room, meeting room or auditorium.
CanadaThis Class A digital apparatus complies with Canadian ICES-003.
 
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.Agency ApprovalsUL, CUL, TUV
 
Other specific Country Approvals may apply, please see product certification label. This user ’s guide applies to models IN10, M6, LP70+, and M2+.InFocus reserves the right to alter product offerings and specifications at any time. 
						

							2
Table of Contents 
Introduction 3
Connecting a computer  5
Required computer connections 5
Displaying a computer image  6
Adjusting the image  7
Connecting a video device  8
Shutting down the projector  9
Troubleshooting your setup  9
Using the keypad buttons  16
Using the remote control  17
Optimizing computer images  18
Presentation features  18
Optimizing video images  18
Customizing the projector  18
Using the menus  19
Picture menu  20
Settings menu  23
Maintenance 26
Cleaning the lens  26
Cleaning the lamp filter screens 26
Using the security lock  26
Replacing the projection lamp  27
Appendix 29
Projected image size  29
Important Operating Considerations for Safety
Place the projector in a horizontal position no greater than 15 degrees 
off axis.
 Locate the projector in a well-ventilated area without any obstructions 
to intake or exhaust vents. Do not place the projector on a tablecloth or 
other soft covering that may block the vents.  Locate the projector at least 4 (1.2 m) away from any heating or cooling 
vents. Use only the power cord provided. A surge-protected power strip is 
recommended. Refer to this guide for proper startup and shutdown procedures.Wa r n i n g : Hg – Lamp contains mercury. Manage in accordance 
with local disposal laws. See www.lamprecycle.org. In the unlikely event of a lamp rupture, particles may exit through the 
projector side vents. When the projector is turned on, keep people, 
food, and drinks out of the keep out area around the projector, as 
indicated by the X area below.Follow these instructions to help ensure image quality and lamp life over 
the life of the projector. Failure to follow these instructions may affect the 
warranty. For complete details of the warranty, see the Warranty booklet.
2’ / 0.6 m
3’ / 1 m 
						

							3
IntroductionYour new XGA 1024x768 resolution digital projector is
 specifically 
designed for portability, connectivity, and collaboration. It is easy to 
connect, easy to use, easy to transport, and easy to maintain
 
Product specificationsTo read the latest specifications on your multimedia projector, be sure to 
visit our website at www.infocus.com, as specifications are subject to 
change. AccessoriesThe standard accessories that came with your projector are listed in the 
included user ’s guide. Optional accessories can be found on our website at 
www.infocus.com or at your retailer or dealer.Online RegistrationRegister your projector on our website at www.infocus.com/register to acti
-
vate your warranty and receive product updates, announcements, and reg
-
istration incentives. 
Projector components and features
keypad zoom ring
focus ring
 
remote control sensor (IR)
adjustable footspeaker
foot release
lamp housing
leveling foot
connectors
 
power connectorsecurity lock
remote control sensor (IR) 
						

							4
Connector PanelThe projector provides computer and video connectors:  one M1-D/A (HD, DVI, and computer) one S-video one composite RCA videoone audio inConnector panel 
Audio inS-video
Composite videoComputer 
						

							5
Connecting a computerRequired computer connectionsConnect the black end of the computer cable to the Computer connector on 
the projector. Connect the blue end to the video port on your computer. If 
you are using a desktop computer, you first need to disconnect the monitor 
cable from the computer ’s video port. 
 
Some Macintosh® computers do not have a standard VESA-out video port. 
If the supplied computer cable will not connect to your computer, purchase 
the appropriate adapter from your Apple® reseller.Connect the black power cable to the connector on the back of the projector 
and to your electrical outlet.The LED turns amber.NOTE: Always use the power cable that shipped with the projector. 
 
Optional computer connectionsTo advance slides in a PowerPoint™ presentation using the up and down 
arrow buttons on the remote, plug the USB connector on the computer cable 
into the USB mouse connector on your computer.To have sound with your presentation, connect an audio cable (sold sepa
-
rately) to your computer and to the Audio In connector on the projector. 
 
 
connect computer cable
  audiocomputer 
						

							6
Displaying a computer image Remove the lens cap.
 
    Press the Pow e r button on the top of the projector or the remote.The LED blinks green and the fans start to run. When the lamp comes on, 
the start up screen displays and the Power light is steady green. It can take a 
minute for the image to achieve full brightness. 
? No startup screen? Get help on 
page
 9. 
Turn on your computer.The computer ’s image should appear on the projection screen. If it doesn’t, 
press the Source button. Make sure your laptop’s external video port is active. Many laptops do not automatically turn on their external video port when a 
projector is connected. Usually a key combination like FN + F8 or CRT/LCD 
key turns the external display on and off. Locate a function key labeled 
CRT/LCD or a function key with a monitor symbol. Press FN and the 
labeled function key simultaneously. Refer to your laptop’s documenta
-
tion to learn your laptop’s key combination.
? No computer image? Get help on 
page
 9. 
 remove lens cappress Power buttonturn on computeractivate laptop’s external port 
						

							7
Adjusting the imageAdjust the height of the projector, if necessary, by pressing the release but
-
ton to extend the elevator foot. Rotate the leveling foot (located at the bottom back left corner), if necessary.
 
Position the projector the desired distance from the screen, so that the lens is 
perpendicular to the screen. See 
page
 29 for a table listing screen sizes and distances.
 
   Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced.
 
   If the image is not square, adjust the vertical digital keystone by using the 
buttons on the keypad. Press the upper Key s t o n e  button to reduce the 
upper part of the image, and press the lower Key s t o n e  button to reduce the 
lower part.
 
You can also adjust the keystone via the menus. See 
page
 20. 
Adjust the Contrast or Brightness in the Picture menu. See 
page
 19 for help with the menus.
foot release button
levelin
g foot adjust height
adjust distance
3
.3
 ft.
/1m 22
.2
 f
t./
6
.
7 
ft/4.9 ft./ 9.9 ft./ 33 ft./
10m
6
.8
m
2
m
 
3m
1.5m
adjust zoom and focusfocus
zoomadjust keystone 
						

							8
Connecting a video device If your video device uses a round, four-prong S-video connector, plug the 
 
S-video cable into the S-video Out connector on the video device and into 
the Video 1 connector on the projector. If the device uses a composite video 
connector, plug the composite video cable into the Composite Out connec
-
tor on the video device and into the Video 2 connector on the projector. For audio, plug a mini-plug audio Y-cable
 into the Audio in connector on 
the projector and into the video device’s left and right audio out connectors.
Connect the black power cable to the connector on the back of the projector 
and to your electrical outlet.   NOTE: Always use the power cable that shipped with the projector.
 
 connect S-video and audio cables
audioS-video
S-videoaudio
connect composite video and audio cables
audiovideo
L R
audio video 
						

							9
Shutting down the projectorThe projector automatically blanks the screen after no active source is 
detected for 30 minutes. This blank screen helps preserve the life of the pro
-
jector. The image returns when an active source is detected or a remote or 
keypad button is pressed. Screen SaveYou can make the blank screen appear after five minutes by turning on 
Screen Save in the Settings>System menu. See 
page
 24. There are six time 
options for the Screen Save feature. They range from five minutes to 30 min
-
utes with five minute intervals.Pow e r  S av eThe projector also has a Power Save feature that automatically turns the 
lamp off after no signal is detected for 20 minutes. After 10 additional min
-
utes with no signal, the projector powers down. If an active signal is 
received before the projector powers down, the image is displayed. You 
must press the Pow e r button to display an image after 30 minutes have 
passed. When Power Save is enabled, Screen Save is disabled. See 
page
 24.
Turning off the projectorTo turn off the projector, press the Pow e r button and verify that you want to 
turn the projector off by pressing the Pow e r button again within 3 seconds. 
You can cancel the shutdown by not pressing the Pow e r button a second 
time. The lamp turns off and the LED blinks amber for 1 minute while the 
fans continue to run to cool the lamp. When the lamp has cooled, the LED 
lights amber and the fans stop. Unplug the power cable to completely 
power off the projector.Troubleshooting your setupIf your image appears correctly on the screen, skip to the next section 
(page
 17). If it does not, troubleshoot the setup. 
LEDsThe Lamp LED on top of the projector (
page
 16) will alert you to certain 
problems. A solid red Lamp LED means it is time to change the lamp. See 
page
 27.
A blinking red Lamp LED means different things based on the number of 
“blinks”. After blinking 1-5 times, the light turns off for 2 seconds, then the 
blinking repeats.
 1 blink, lamp won’t turn on: Turn the projector off for at least one 
minute, then turn it on again. If the blinking continues, the lamp may 
need to be replaced. 2 blinks: Remaining lamp life is low. Replace the lamp, see 
page
 27.
 3 or 4 blinks: Unexpected shut down (3 blinks) or fan failure (4 
blinks). Turn the projector off for at least one minute, then turn it on 
again. If the blinking continues, the projector may require service; go 
to www.infocus.com/support. 5 blinks: The projector is overheating. Turn the projector off and 
remove anything that may be blocking its air vents. Leave the projec
-
tor off for at least one minute to let it cool before turning it on again. 
Important: Continuous operation at high temperature may reduce the 
lifetime of the lamp and/or projector.
The other LED on top of the projector indicates the normal operating state 
of the projector.
 A solid green LED means the projector is on. A blinking green LED means the lamp is turning on. A green “blip” 
means the projector is in Screen Save or Power Save mode. A blinking amber LED means the lamp is either warming up or cool
-
ing down to enter standby mode; a solid amber LED means the pro
-
jector is in standby mode.