InFocus Projector SP1080 User Manual

1 Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 
97223-8368 USA
We declare under our sole responsibility that this projector conforms to the following 
directives and norms:
ErP Directive 2009/125/EC
EMC Directive 2004/108/EC
EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1:2005 (2nd Edition) + A1: 2009 and EN 60950-1:2006 + A11:2009 + 
A1:2010 + A12:2011
Trademarks
Apple, Macintosh,...

2 Table of Contents
Introduction 4
Positioning the projector  6
Connecting a computer source  7
VGA connection  7
Connecting power  7
Optional computer connections  7
Displaying an image  8
Adjusting the image  9
Connecting a video device  10
HDMI connection  10
VGA connection  10
Component video connection  10
Audio 10
Shutting down the projector  11
Troubleshooting your setup  11
Using the remote control  19
Using the audio  20
Using the keypad buttons  21
Optimizing computer images  22
Presentation...

3 Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 15 degrees off 
axis.
• Locate the projector at least 4 (1.2m) away from any heating or cooling vents.
• Do not block ventilation openings. Locate the projector in a well-ventilated 
area without obstructions to intake or exhaust vents. Do not place the...

4
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to 
maintain. It is a versatile projector that is flexible enough for home video viewing 
and business presentations too. The SP1080 has native 1080p 1920 x 1080 
resolution. It is compatible with a wide variety of computers and video devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our 
website at www.infocus.com, as specifications are subject...

5 Connector panel
The projector provides both computer and video connection options.
• VGA computer (1)
•HDMI
• USB connector for firmware upgrades, mouse control and Screen Save mode.
• Audio inputs for video and computer.
• Audio output to external speakers.
• RS-232 serial control. Command control codes are on our support website at 
www.infocus.com/support. 
RS232
computer
audio in/out
security lockHDMIUSB 

6
Positioning the projector
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The 
projector must be at least 39.4” (1.0m) from the projection screen.
• If you are installing the projector on the ceiling, we strongly recommend using 
InFocus approved...

7
Connecting a computer source
VGA connection
Connect one end of the provided computer cable to the Computer 1 connector 
on the projector and the other to the VGA connector on your computer. If you 
are using a desktop computer, you will need to disconnect the monitor cable from 
the computer’s video port first.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI 
provides an interface between sources, such as set-top boxes, DVD players, and 
receivers and your...

8
Displaying an image
Press the Power button.
The Power LED blinks green, and the fans start to run. When the lamp comes on, 
the start up screen displays and the Power LED turns solid green. It can take up to 
a minute for the image to achieve full brightness. Note: When the feature, AC 
Power On, is enabled, the projector automatically turns on when power is 
connected. This allows control of ceiling mounted projectors with a wall power 
switch.
No start up screen? Get help on page 12.
Turn on your...

9
Adjusting the image
If necessary, adjust the height of the projector by rotating the elevator foot to 
extend the foot.
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the front of the projector.
Position the projector the desired distance from the screen at a 90 degree angle to 
the screen.
See page 6 for a table listing screen sizes and distances.
Adjust the zoom or focus.
If the image is not square, first make sure...