InFocus Projector ScreenPlay 7210 User Manual

							20
Using the keypad buttonsMost buttons are described in detail in other sections, but here is an over-
view of their functions:
Pow e r–turns the projector on (page 9) and off (page 9).
Menu–opens the on-screen menus (page 23).
Select–confirms choices made in the menus (page 23).
Up/down arrows–navigates to and adjusts settings in the menus (page 23).
Auto image–resets the projector to the source.
Presets–cycles through the 3 available user preset settings (page 26).
Key s t o n e–adjusts squareness of the image (page 10).
Brightness–adjusts intensity of the image (page 24).
Resize–changes the aspect ratio (page 24). 
Source–changes the active source (page 29). 
menu navigation buttons 
						

							21
Using the remote controlThe remote uses two (2) provided AAA batteries. They are easily installed 
by sliding the cover off the remote’s back, aligning the + and - ends of the 
batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not 
at the video device or computer). The range of optimum operation is up to 
30 feet (9.14m).
Press the remote’s Menu button to open the projector ’s menu system. Use 
the arrow buttons to navigate, and the Select button to select features and 
adjust values in the menus. See page 23 for more info on the menus.
The remote also has:
Pow e r button to turn the projector on and off (see page 12 for shut-
down info)
 backlight button to light the remote’s buttons in the dark
Brightness and Contrast buttons to adjust the image
Blank button to display a blank screen instead of the current image (to 
change the color of the blank screen, see page 30)
Source buttons to switch among sources (to assign a particular source 
to a source button, see page 29) and a source toggle
Resize button to change the Aspect Ratio (see page 24)
Auto Image button to resynchronize the projector to the source
Preset button to restore stored settings (see page 26)
Overscan button to remove noise in a video image (page 26)Troubleshooting the remote Make sure the batteries are installed in the proper orientation and are 
not dead.
 Make sure you’re pointing the remote at the projector or the screen, not 
at the video device or the computer, and are within the remote range of 
30 feet (9.14m).
backlight button
navigation buttons 
						

							22
Optimizing video imagesAfter the video device is connected properly and the image is on the screen, 
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 23.
 Change the Aspect ratio. Aspect ratio is the ratio of the image width to 
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV 
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your 
input source in the menus, or press the Resize button on the remote to 
cycle through the options. See page 24.
 Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture 
menu. See page 24. 
 Select a different Color Temperature or use the Color Control to adjust 
the gain and offset of the red, green, and blue color. See page 28.
 Select a specific Color Space or Gamma. See page 26 and page 28.
 Select a different Video Standard. Auto tries to determine the standard 
of the incoming video. Select a different standard if necessary. See 
page 28.
 Turn Overscan on to remove noise around the video image. See 
page 26. 
 Fine tune component inputs using the TrueLife™ adjustments. See 
page 27.
 Tune colors to your specifications using Blue Only and ADC Calibra-
tion. See page 31.
 Choose High Power to maximize the light output. See page 29.
 Make sure your DVD player is set for a 16:9 television. See your DVD 
player ’s user ’s guide for instructions.
Customizing the projectorYou can customize the projector for your specific setup and needs. See 
page 29 to page 31 for details on these features.
 For rear projection, turn Rear mode on in the Settings>System menu.
 For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu. 
 Turn the projector ’s display messages and power-on chime on and off.
 Turn on power saving features. 
 Specify blank screen colors and startup logos. Make the menus translu-
cent.
 Specify the menu language. 
						

							23
Using the menusTo open the menus, press the menu button on the keypad or remote. (The 
menus automatically close after 60 seconds if no buttons are pressed.) The 
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button. 
To change a menu setting, highlight it, press Select, then use the up and 
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm 
your changes. Use the arrows to navigate to another setting. When your 
adjustments are complete, navigate to Previous, then press Select to go to 
the previous menu; press the Menu button at any time to close the menus. 
Dots appear before the menu name. The number of dots indicate the menu’s 
level, ranging from one (the Main menu) to five (the most nested menus). 
The menus are grouped by usage:
 The Picture menu provides image adjustments.
 The Settings menu provides set-up type adjustments that are not 
changed often.
 The About menu provides a read-only display of information about the 
projector and source. 
Certain menu items may be hidden until a particular source is connected. 
For example, Tint is only available for NTSC video sources and will be hid-
den when other sources are active. Other menu items may be grayed out 
when they are not available. For example, Brightness is grayed out until an 
image is active.
Keypad navigation 
buttons
Main menuMenu
button
 
 
Picture menuSettings menu Dots
About menu 
						

							24
Picture menuTo adjust the following five settings, highlight the setting, press Select, use 
the up and down arrows to adjust the values, then press select to confirm 
the changes. All menu defaults are listed in a table starting on page 38.
Key s t o n e: adjusts the image vertically and horizontally to make a squarer 
image. The two keystones ranges are interdependent. The combined num-
ber of steps for both is 50. If one keystone is set to 65, it is 15 steps above the 
center position of 50. This leaves 35 steps that the other keystone can vary 
from the center of 50. This means it cannot go below 15 or above 85.
Contrast: controls the degree of difference between the lightest and darkest 
parts of the picture and changes the amount of black and white in the 
image.
Brightness: changes the intensity of the image. You can also adjust bright-
ness from the keypad.
Color: (video sources only) adjusts a video image from black and white to 
fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the 
image.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. 
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 
1.78:1, or 16:9. You can choose Native, 4:3, 16:9, Letterbox, or Natural Wide. 
The default is 16:9. The goal is to show the most detail on the screen while 
preserving the ratio of width to height. The native resolution of the projec-
tor is 1280x720. Use Native, 4:3 or Natural Wide for 4:3 input sources; use 
Native, 16:9 or Letterbox for 16:9 input. Pressing the Resize button on the 
remote cycles through these options.
Native: this mode bypasses the internal scaler, displaying the image with no 
resizing. Since the native resolution is 1280x720 and 4x3 video images are 
approximately 640x480, 4x3 images will always be smaller than the display 
and will be centered in the display. Computer images 1024x768 or smaller 
will also be centered in the display. If a 16x9 video source or a 1280x1024 or 
larger computer source is viewed, it will display up to 1280 pixels and 720 
lines from the center of the input.
Keystone 
Picture menu
Aspect ratio 
						

							25
16:9: the default is 16:9, which preserves the 16:9 aspect ratio and is 
designed to be used with content that is Enhanced for Widescreen TVs. 
4:3: resizes the image from its original version to fit a standard 4:3 
aspect ratio screen. If you have a 4:3 source on a 16:9 screen, the image 
is placed in a 16:9 space, so black bars appear at the sides of the image.
Letterbox: preserves the 16:9 aspect ratio. If you have a 16:9 source and 
screen, the image fills the screen. If your source is letterboxed, the 
image is expanded to fill the screen.
Natural Wide: this mode stretches a 4:3 image to fill the entire 16:9 
screen. The center two-thirds of the image is unchanged; the edges of 
the image are stretched. The mode is only available when TrueLife is 
active (see page 27).
16
16 99 16:9 image input16:9 image 
16:9
aspect ratio16 9
4 34:3 image input4:3 image on 16:9 screen
black bars
black bars
4:3 aspect ratio
16 9 letterbox image input
16:9 image fills 16:9 screen
black bars
black bars
4 3 letterbox
aspect ratio
4:3 image fills 16:9 screen
natural wide
aspect ratio4:3 image input
4 3
16 9 
						

							26
Presets: This allows you to customize settings and save the settings to be 
restored later. To restore the factory default settings, choose Factory Reset in 
the Settings>Service menu. 
To set a preset for the current source, adjust the image, select Save Settings 
in the Presets menu, then choose Save User 1, 2, or 3. You can recall these 
settings in the future by selecting the appropriate user presets. 
Gamma: Gamma tables contain preset intensity configurations optimized 
for the input source. You can select a gamma table that has been specifically 
tuned for either film, CRT (Cathode Ray Tube), video, Bright Room, or PC 
input. (Film input is material originally captured on a film camera, like a 
movie; video input is material originally captured on a video camera, like a 
TV show or sporting event.) White Peaking increases the brightness of 
whites that are near 100%.
NOTE: Your viewing preferences may vary. Cycle through the gamma 
options and pick the one you like the best.
Overscan: (video sources only) removes noise around the video image.
Save User Presets
Presets
GammaOverscan 
						

							27 Advanced settings
The following 4 options are for computer or HDTV sources only. 
Phase: adjusts the phase of the video signal’s digital conversion.
Tr a c k i n g: adjusts the frequency of the video signal’s digital conversion. 
Horizontal/Vertical Position: adjusts the position of the source.
Sync Threshold Adjust: If a hardware device, such as a DVD player, is not 
syncing properly with the projector, adjust this option to help it to sync 
when connected to the projector. 
Tr u e L i f e: This option refers to Faroudja’s TrueLife processing of the image. 
All standard definition interlaced video signals (composite, S-video and 
component) are routed through this processor. Extended and High Defini-
tion progressive component sources are not routed though this processor by 
default. You can turn TrueLife on to route these signals through the proces-
sor and then adjust the following 3 options:
Chroma Detail: This adjusts the color sharpness.
Luma Detail: This adjusts the overall sharpness (edge enhancement) of 
the Luma signal. 
Chroma Delay: aligns the Luma and Chroma signals.
CCS: (Cross Color Suppression) processes the signal to remove any color 
information from the luma portion of the signal. It is On for all composite 
signals, Off for all component signals, and can be turned on or off for all S-
video signals.
Film Mode: controls deinterlacing. If 2:2/3:2 Enable is selected, the deinter-
lacer attempts to perform a 3:2 pulldown, assuming the source was origi-
nally created on 24fps film. If the original source is 30fps film, you should 
select NTSC 2:2 pulldown.
Noise Reduction: adjusts signal noise reduction. Choose Off to have no 
noise reduction, choose Auto to have the software determine the amount of 
noise reduction, or choose Manual and adjust the Level. Skintone Bypass 
prevents the noise reduction from being performed on skin tones, thus pre-
venting them from appearing overly softened.
AdvancedTrueLifeFilm ModeNoise Reduction 
						

							28
Color Space: This option applies to computer and HDTV sources (it won’t 
appear in the menu for video sources). It allows you to select a color space 
that has been specifically tuned for the video input. When Auto is selected, 
the projector automatically determines the standard. To choose a different 
setting, turn off Auto, then choose RGB for computer sources, choose 
REC709 for component 1080i or 720p sources, or choose REC601 for compo-
nent 480p or 576p sources.
Color Temperature: changes the intensity of the colors. Select a listed 
value.
Color Control: allows you to individually adjust the gain (relative warmth 
of the color) and the offset (the amount of black in the color) of the red, 
green, and blue colors. 
Video Standard: When it is set to Auto, the projector attempts to pick the 
video standard automatically based on the input signal it receives. (The 
video standard options may vary depending on your region of the world.) If 
the projector is unable to detect the correct standard, the colors may not 
look right or the image may appear “torn.” If this happens, manually select 
a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-
dard menu.
VCR: When checked, the VCR option is used to eliminate discoloration of 
about 25% of the image near the top caused by poor quality input image 
content.
Color SpaceColor TemperatureColor ControlVideo Standard 
						

							29
Settings menuSources
: allows you to assign a particular input to a specific source key on 
the remote and enables or disables Autosource. When Autosource is not 
checked, the projector defaults to the last-used source. If no source is found, 
a blank screen displays. When Autosource is checked, the projector checks 
the last-used source first at power up. If no signal is present, the projector 
checks the sources in order until a source is found or until power down. 
You can use the Source Enable feature to eliminate certain sources from this 
search, which will speed the search. By default, the check boxes for all 
sources are checked. Uncheck a source’s box to eliminate it from the search.
System
All options in this menu toggle between on and off.
Rear: reverses the image so you can project from behind a translucent 
screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
NOTE: It is recommended that all final image adjustments in Ceiling 
mode are made once the unit has fully warmed up (approximately 20 
minutes).
Auto Power: When Auto Power is checked, the projector automatically 
goes into the startup state after the projector receives power. This 
allows control of ceiling mounted projectors with a wall power switch.
Display Messages: displays status messages (such as “Searching”) in 
the lower-left corner of the screen.
High Power: Turn this on to increase the light output of the lamp. This 
also shortens lamp life and increases fan noise.
Sources Settings menu
Source Enable
Source 1
System menu