InFocus Projector Lp800 User Manual

21
BASIC OPERATION
Press FREEZE button on Remote Control Unit to freeze picture on-screen.  To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT / RIGHT CLICK / LASER button.
PICTURE FREEZE FUNCTION
Press P-TIMER button on Remote Control unit.  Timer display “00 : 00”
appears on screen and timer starts to count time (00 : 00 ~ 59 : 59).  
To stop P-TIMER display, press P-TIMER button.  And then, press P-
TIMER button again to cancel P-TIMER function....

22
COMPUTER INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
Choose Computer by pressing INPUT button on Top Control or on
Remote Control Unit.
If projector cannot reproduce proper image, select correct input source
through MENU OPERATION (see below).
INPUT button
Input 1
Input 2
Input 3
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to RGB, and then press...

23
COMPUTER INPUT
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to
“COMPATIBLE COMPUTER SPECIFICATION” on page 26).  When selecting Computer, this projector automatically tunes
to incoming signal and projects proper image without any special setting.  (Some computers need setting manually.)
Note : Projector may display one of following messages.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto...

24
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed.  However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector.  If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a...

25
COMPUTER INPUT
NOTE :  Display area (H/V) and Full screen cannot be adjusted when
“1035i (HDTV)” or “1080i (HDTV)” is selected on PC
SYSTEM Menu (P23).
Selects area displayed with this projector. Select resolution at
Display area dialog box.
Display area
Adjustment of horizontal area displayed with this projector.  Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area H
Adjustment of vertical area displayed with this projector.  Press
POINT LEFT/RIGHT...

26
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 160 MHz of Dot Clock.
NOTE :Specifications are subject to change without notice.
ON-SCREEN
DISPLAYRESOLUTIONH-Freq.
(kHz)V-Freq.
(Hz)
VGA 1640 x 48031.4759.88
VGA 2720 x 40031.4770.09
VGA 3640 x 40031.4770.09
VGA 4640 x 48037.8674.38
VGA 5640 x 48037.8672.81
VGA 6640 x 48037.5075.00
MAC LC13640 x 48034.9766.60
MAC 13640 x 48035.0066.67
MAC...

27
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENTS
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.1
2Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.
Move a red frame icon to level and
press SELECT button.
Level being selected.
IMAGE SELECT MENU
Normal picture level preset on this projector.
Standard
Picture level with improved halftone...

28
COMPUTER INPUT
Press POINT LEFT/RIGHT buttons
to adjust value.
Reset all adjustment to previous figure.
Reset
Store
Closes IMAGE MENU.
Quit
Other icons operates as follows.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.1
2Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed.  Adjust each level by pressing POINT
LEFT/RIGHT...

29
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. Zoom +” is displayed.  Press SELECT button to
expand image size.  And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image.  Panning function can work...

30
VIDEO INPUT
When video input signal is connected to Y-Pb/Cb-
Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.Y,Pb/Cb,Pr/Cr
SELECTING INPUT SOURCE
Press MENU button and ON-SCREEN MENU will appear.  Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.1
Move a pointer to source
and press SELECT button.
Source Select Menu (VIDEO)
Move a pointer to source that you want to select and then press
SELECT button.3
When video input signal is connected to VIDEO jack,
select Video.Video
When video...