InFocus Projector Lp600 User Manual

							41
 Be extremely careful when removing the lamp housing. In the unlikely 
event that the lamp ruptures, small glass fragments may be generated. 
The lamp module is designed to contain most of these fragments, but 
use caution when removing it. Before replacing a ruptured lamp, clean 
the lamp compartment and dispose of cleaning materials. Wash hands 
after lamp replacement. This product has a lamp which contains a very 
small amount of mercury. Dispose of it as required by local, state or fed-
eral ordinances and regulations. For more information see 
www.eiae.org.5
Detach the lamp connector from the projector by gently pulling the con-
nector until it is disconnected from the projector.
6
Carefully remove the lamp module by grasping and lifting the metal 
bail wire. Dispose of the lamp in an environmentally proper manner. 
7
Install the new lamp module, making sure that it is properly seated. Be 
careful not to touch the interior components of the projector.
8
Snap the bail wire back into its flat position against the lamp module.
9
Re-attach the lamp connector to the projector. Make sure the connector is 
fully inserted.
10
Tighten the screw on the lamp module.
11
Replace the lamp door.
12
Plug in the power cable then press the Powe r button to turn the projec-
tor back on, then reset the lamp hour timer. 
Resetting the lamp timerIf the lamp timer has reached the maximum number of hours for the projec-
tor lamp, the LED on the projector ’s keypad will show a lamp error (see 
“LED behavior and meaning” on page 16). To reset the lamp timer, press the 
decrease volume button on the keypad and the increase volume button 
simultaneously for 10 seconds. You can also navigate to the Settings>Ser-
vice menu and select Lamp Reset to reset the lamp timer. 
disconnect lamp connectorremove module using bail wire
reset lamp time in Service menu 
						

							42
Cleaning the lamp filter screensIn dirty or dusty environments, the dust filter screens on the lamp module 
and lamp door and in the lamp compartment
 can become clogged, causing 
high temperatures inside the lamp module. These high temperatures can 
impact lamp performance and operating life. Routine maintenance to 
remove dust and dirt from the screens lowers the lamp operating tempera-
ture and prolongs lamp life. To maximize lamp life you will need to clean 
the screens every 250 hours. Lamp screen maintenance may need to occur 
more often than 250 hours depending on your installation/use environ-
ment.
1
Remove the lamp module. Refer to page 40 for instructions.
2
Examine the dust filter screens on each side of the lamp module. If nec-
essary, use compressed or canned air to clean the screens. Then use a 
cotton swab dipped in isopropyl alcohol to lightly wipe each screen. 
After youve wiped each screen, blow away any remaining contami-
nants.
3
Before you replace the lamp, repeat the cleaning process on the screen in 
the lamp compartment in the projector.
4
Examine the dust filter screen on the lamp door. If necessary, use com-
pressed or canned air to clean the screen.
5
Replace the lamp module and lamp door.
screen
screen
screen
screen 
						

							43
AppendixAccessoriesNOTE: Use only approved accessories. Standard Accessories
(ship with the projector)
Part Number
Carry Case 110-0819-xx
Computer Cable 6 ft (1.8 m) SP-DVI-A
Video Cable 6 ft (1.8 m) 210-0176-xx
Audio Cable 6 ft (1.8 m) 210-0118-xx
Audio Cable Adapter 210-0177-xx
Power Cable*  516-0052-xx
Navigator Remote 590-0728-xx
Projection Lamp Module (included 
in projector)SP-LAMP-019
Lens Cap 340-1347-xx
Lens Cap Tether 321-0192-xx
Quick Setup card 009-0911-xx
User’s Guide with CD 010-0546-xx
Safety Card 009-0659-xx
Color-coded Cable Ties, 3 set SP-CABLETIES
SCART Adapter* 301130
*country-dependent
Optional Accessories  Part Number
Shipping Case (ATA approved)  CA-ATA-020
Projector Mount SP-CEIL-011
False Ceiling Plate for Projector Mount SP-LTMT-PLT
Extension Arm for Projector Mount 
26” - 47”SP-LTMT-EXTP
Organizer Carry Case CA-C230
DVI-D Cable 6 ft (1.8 m) SP-DVI-D
M1 to Component Adaptor SP-M1-ADPT
LiteShow Wireless Connection LP-LITESHOW
Audio/Video Cable, 30 ft (9m) SP-AV30
Projector Cable Lock System SP-LOCK-B
50” Diagonal Screen (portable) A650
60” Diagonal Screen (portable) HW-DLXSCRN
84” Diagonal Wall/Ceiling Mounted Screen HW-WALLSCR84
Replacement Lamp Module SP-LAMP-019
RF Presenter Remote Control HW-PRESENTER-RF
IR Presenter Remote Control HW-PRESENTER
IR Conductor + Remote Control HW-CONDUCTOR+ 
						

							44
Red LED behavior and projector errorsIf the projector is not functioning properly and the red LED is blinking, con-
sult Ta b l e  4 to determine a possible cause. There are two second pauses 
between the blinking cycles. Visit our website for more details on the red 
LED error codes. See the inside back cover for contact information.
Projected image sizeNOTE: Visit our website for an interactive image size calculator.
Table 4: 
Red LED Behavior Explanation
One (1) blink The lamp wont strike after five (5) 
attempts. Check the lamp and lamp door 
installations for loose connections.
Two (2) blinks The lamp counter hours have exceeded 
lamp life hours. Replace the lamp and 
reset the lamp hours counter.
Three (3) blinks The projector has shut down the lamp. 
Replace the lamp. Contact Technical Sup-
port for repair if replacing the lamp does 
not solve the problem.
Four (4) blinks The fan has failed. Contact Technical Sup-
port for repair.
Five (5) blinks The projector is overheating. Check for a 
blocked air vent. Contact Technical Sup-
port for repair if clearing the air vents 
does not solve the problem.Table 5: 
Image sizes 
Distance 
to screen 
(feet/m) Minimum 
Diagonal
(feet/m)Maximum 
Diagonal
(feet/m)Minimum 
Horizontal
(feet/m) Maximum
Horizontal 
(feet/m)
5/1.5 2.75/0.83 3.4/1.02 2.2/0.66 2.73/0.82
10/3 5.5/1.65 6.8/2.04 4.41/1.32 5.46/1.64
15/4.6 8.25/2.53 10.2/3.13 6.61/2.03 8.2/2.51
20/6.1 11/3.36 13.6/4.15 8.81/2.69 10.93/3.33
30/9.1 16.5/5.01 20.4/6.19 13.22/4.01 16.39/4.97
32.8/10 18.0/5.5 22.3/6.8 14.45/4.41 17.92/5.46 
						

							45
INDEX
Numerics
1024x768 resolution 5
A
About menu 30, 38
Advanced setting 33
advancing PowerPoint slides 7
advancing PowerPoint slides with LitePort 27
Aspect Ratio 31, 38
audio 28
audio adapter 13
Audio In connector 7, 13
audio volume 15
audio, troubleshooting 28
Auto Advance 36
Auto Ceiling 34
Auto Image 38
Auto Play 36
Auto Power 34
Autosource 34
B
Blank screen 37, 38
blinking green 16
blinking red 16
Brightness 12C
cables
optional 43
standard 43
Ceiling 34
cleaning the lamp filter screens 42
cleaning the lens 39
Color 15, 31
Color Control 33
Color Space 33
Color Temperature 33
colors are incorrect 22
Computer 2 connector 8
computer connections
optional 7
required 7
computer image
optimize 29
troubleshooting 17
connecting
computer 7
external speakers 28
USB device 8
video device 13
connector panel 6
contacting InFocus 24
Contrast 12, 15, 31
customer service contact information 24 
						

							46
D
Display Messages 34
displaying
computer image 9
JPEG image 27
video image 14
displaying JPEG images with LitePort player 27
Drivers 10
USB 11
Windows 98 11
E
Effect Key 38
elevator foot 12
F
Factory Reset 38
first time use
driver installation 10
Fit to Screen 36
focus 12, 15
Freeze 38
fuzzy image 18I
image
display computer 9
display JPEG 27
display video 14
image does not fit screen 21
image not centered 23
image not sharp 21
image not square 21
image reversed 22
image size matrix 44
image upside down 22
Interactive Display 5
K
keypad buttons 25
keystone 12, 31
L
lamp
cleaning filter screens 42
lamp replacement 40
Lamp Reset 38
lamp screens, cleaning 42
lamp won’t turn on 23, 24
Language 38
laptop
connecting 7
external video port 9
LED
blinking green 16
blinking red 23
solid green 16
solid red 24
LED behavior 16
lens cap tether 5 
						

							47
lens, cleaning 39
leveling foot 12
LitePort
connector 6, 8
menu 36
player 6, 8, 27, 36
player modes 27
Rotate effect key 38
rotating images 38
LitePort Utility software 6
LiteShow 6
lock, security 39
Low Power 34
M
Macintosh troubleshooting 19
Main menu 30
menu system 30
Monitor connector 8
Monitor Out Enable 34
Mute 38
N
no computer image 18
no startup screen 17
O
online registration 5
only startup screen appears 17
onscreen menus 30
optional accessories 43
Overscan 33P
Picture menu 31
Play All 36
Position 33
power cable 7, 13
Power Save 16, 35
PowerPoint, advancing slides 7
Power-up Source 34
presentation features 29
projected image sizes 44
projector
adjusting the height 12, 14
connector panel 6
customizing 29
LitePort player 8, 27
optional accessories 43
positioning 12
shutdown 16
standard accessories 43
troubleshooting problems 16
USB connector 8
R
Rear 34
registering your projector 5
remote control 26
advancing slides 26
Effect key 26
not working 20
Previous/Next buttons 26
replacing the lamp 40
Reset 38
resetting the lamp timer 41
resolution 5
RS-232 6, 8 
						

							48
S
safety considerations 4
Screen Save 16, 35
Screen Saver 35
screens, cleaning 42
security lock 39
serial connection 8
Service 38
Settings menu 34
Sharpness 33
shutting down the projector 16
Slide Transition 36
solid green 16
solid red 16
Source troubleshooting 17
Sources 34
speakers, connecting 28
standard accessories 43
Startup Logo 37
S-video connector 13
Sync Threshold Adjust 33
T
Tint 15, 31
Tracking 33
Troubleshooting 16, 17
Turning off the projector 16U
USB drivers 11
USB mass storage device 8
USB, connecting 7
using the keypad buttons 25
V
VESA connector 8
video connections
optional 13
standard 13
Video connector 13
video images, optimizing 29
Video Standard 33
W
White Peaking 33
Windows 2000 11
Windows 98 10
Windows ME, XP 11
wireless projection 6
X
XGA 5
Z
zoom 12, 15 
						

							49
Limited Warranty
Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-
poration (“InFocus”) warrants that the Projector, Lamps and Accessories 
(hereinafter collectively or individually referred to as “Product” as appro-
priate) purchased from InFocus, an InFocus distributor, or an InFocus 
reseller will conform to InFocus’ specifications and be free from defects in 
material or workmanship for the respective Limited Warranty period pro-
vided below. InFocus does not warrant that the Product will meet the spe-
cific requirements of the end-user customer.
If the Product while subject to this Limited Warranty, is defective in material 
or workmanship during the warranty period, then InFocus, at its option, 
will REPAIR or REPLACE the Product.
All exchanged parts and Products replaced under this Limited Warranty 
will become property of InFocus. InFocus sole obligation is to supply (or 
pay for) all labor necessary to repair the Product found to be defective 
within the Limited Warranty period and to repair or replace defective parts 
with new parts or, at the option of InFocus, serviceable used parts that are 
equivalent or superior to new parts performance. Limited Warranty periods 
are as follows: 
Projector Product Limited Warranty Period (Excluding Lamps)
: 
Two (2) years from date of purchase. 
Lamp Product Limited Warranty Periods
: From the date of Projector 
Product purchase, the original installed lamp shall have a 90-day or 500 
hours usage Limited Warranty Period, whichever comes first.
Replacement Lamps purchased at the time of Projector Product pur-
chase will have a 90-day or 500 hours usage Limited Warranty Period 
from the date of installation, whichever comes first.
Replacement lamps purchased after the time of Projector Product pur-
chase shall have a 90-day or 500 hours usage Limited Warranty Period 
from the date of replacement lamp purchase, whichever comes first. 
Accessory Product Limited Warranty Period
: one (1) year from date 
of purchase. WARRANTY LIMITATION AND EXCLUSION
THIS WARRANTY SETS FORTH INFOCUS’ MAXIMUM LIABILITY FOR 
ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-
CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER. 
InFocus shall have no further obligation under the foregoing Limited War-
ranty if the Product has been damaged due to abuse, misuse, neglect, smoke 
exposure (cigarette or otherwise), accident, unusual physical or electrical 
stress, unauthorized modifications (including use of an unauthorized 
mount), tampering, alterations, or service other than by InFocus or its 
authorized agents, causes other than from ordinary use or failure to prop-
erly use the Product in the application for which said Product was intended.
This Limited Warranty excludes Product cleaning, repair, or replacement of 
plastics due to cosmetic damage and damage as a result of normal wear. 
Product repair outside of the terms of the Limited Warranty will be on a 
time and materials basis. Prolonged Product “demonstration” causes 
unusual Product wear and is not considered normal use under the terms of 
this Limited Warranty.
The Accessory Product Limited Warranty covers the accessory item only 
and excludes normal wear. The Lamp Product Limited Warranty excludes 
expected lamp degradation.
Remanufactured Products and Software Products are exempt from the fore-
going Limited Warranty. Please refer to the appropriate Remanufactured 
Product Limited Warranty or Software Product Limited Warranty for appli-
cable Warranty information.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-
CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR 
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-
RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR 
PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT 
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF 
AND 
THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED 
OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS. 
SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW 
LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS 
MAY NOT APPLY TO YOU. 
						

							50
Limited Warranty PeriodThe Limited Warranty periods hereof commence on the date of purchase by 
the end-user customer. These Limited Warranty provisions shall apply only 
to the end-user purchaser (first person or entity that purchased a new Prod-
uct for personal or business use and not for the purpose of distribution or 
resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS 
WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE 
DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL 
SUCH CONSUMER RIGHTS.
To Be Eligible For Limited Warranty CoverageAny person exercising a claim under this Limited Warranty must establish 
to the satisfaction of InFocus both the date of purchase and that the Product 
was purchased new. The sales receipt or invoice, showing the date of pur-
chase of the Product is the proof of the date of purchase.
To Obtain Warranty ServiceDuring the Limited Warranty period, to exercise this Limited Warranty, the 
purchaser must first contact 1) InFocus, 2) a service facility authorized by 
InFocus or 3) the place of original purchase. InFocus Customer Service – 
1-503-685-8888 or visit www.infocus.com/service
For Warranty service, the purchaser will be advised to return or deliver the 
defective Product freight and all fees prepaid, to an InFocus Service Center 
or to a service facility authorized by InFocus. When returning Product to 
InFocus, a Service Request Number (SR #) is required and must be clearly 
displayed on the outside of the shipping carton or a similar package afford-
ing an equal degree of protection. InFocus or the service facility authorized 
by InFocus will return the repaired/replaced Product freight prepaid to the 
purchaser.
Products returned for Warranty service must be accompanied by a written 
letter that: (i) explains the problem; (ii) provides proof of date of purchase; 
(iii) provides the dealer ’s name; and (iv) provides the model and serial 
number of the Product. Upon request of InFocus Corporation or an autho-
rized repair center for InFocus, proof of legal import must accompany the 
warranty repair Product, otherwise the Product must be returned to the 
place of original purchase, to the manufacturer (Purchaser must bear all tax, 
duty and freight), or the Purchaser must bear charges for the warranty 
repair.No repair or replacement of Product or part thereof shall extend the Limited 
Warranty period as to the entire Product. Warranty on the repair part and 
workmanship shall only be effective for a period of ninety (90) days follow-
ing the repair or replacement of that part or the remaining period of the 
Product Limited Warranty whichever is greater.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY 
WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN 
NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF 
THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND 
UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-
CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR 
LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE 
STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING 
INFOCUS’ LIABILITY.
Limitation on Bringing Action
 - No action, regardless of form, arising out 
of the agreement to purchase the Product may be brought by purchaser 
more than one year after the cause of action has accrued.
Governing Law
 - Any action, regardless of form, arising out of the agree-
ment to purchase the Product is governed by Oregon law.
Mandatory Arbitration
 – Any action, regardless of form, arising out of the 
agreement to purchase the Product is subject to mandatory arbitration.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE 
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS 
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND 
YOU MAY ALSO HAVE OTHER RIGHTS, DEPENDING ON JURISDIC-
TION.