InFocus Projector Learn Big In2104ep User Manual

							10
Displaying an image Press the Pow e r button.The Power light on the Status Indicator Panel (
page
 14) blinks green and the 
fans start to run. When the lamp comes on, the start up screen displays and 
the Power light is steady green. It can take a minute for the image to achieve 
full brightness. 
? No start up screen? Get help on 
page
 14. 
 
Turn on your computer or video device.The image should appear on the projection screen. If it doesn’t, press the 
Source button on the projector’s keypad or remote. If using a laptop, make sure it’s external video port is active. Many laptops do not automatically turn on their external video port when a 
projector is connected. Usually a key combination like FN + F8 or CRT/LCD 
key turns the external display on and off. Locate a function key labeled 
CRT/LCD or a function key with a monitor symbol. Press FN and the 
labeled function key simultaneously. Refer to your laptop’s documenta
-
tion to learn your laptop’s key combination. 
? No laptop image? Try pressing the Auto Image button on the key
-
pad. Get help on 
page
 15. 
 press Power buttonturn on computer or video deviceactivate laptop’s external port
FN keymonitor key
or LCD/CRT key  
						

							11
Adjusting the imageIf necessary, adjust the height of the projector by pressing the elevator foot 
release button to extend the foot. If necessary, rotate the leveling foot located at the rear of the projector.
 
 Avoid placing your hands near the hot exhaust vent at the side of the projec
-
tor.Position the projector the desired distance from the screen at a 90 degree 
angle to the screen. See 
page
 5 for a table listing screen sizes and distances.
 
  Adjust the zoom or focus.
 
    If the image is not square, first make sure that the projector is perpendicular 
to the screen. If the image is larger or smaller on the top or bottom edge of 
the screen, press the top Key s t o n e button to reduce the upper part of the 
image, and press the bottom Key s t o n e button to reduce the lower part.If the left or right side of the screen is larger or smaller the other, you can 
turn the projector to the left or to the right a few degrees to square the 
image.Adjust the Contrast or Brightness in the Basic Picture menu. See 
page
 28 for 
help with these menu adjustments.For Aspect Ratio, keep in mind that DVD players must be configured for 
16:9 in order to view the highest quality image. For more information 
regarding Aspect Ratio, see 
page
 12.
adjust height
elevator
foot
release button
adjust distanceadjust zoom or focus
focus
(front ring)
(rear ring)zoom
adjust keystoneadjust Basic Picture menu 
						

							12
Connecting a video deviceYou can connect video devices such as VCRs, DVD players, camcorders, 
digital cameras, video game consoles, HDTV receivers, and TV tuners to the 
projector. You can connect the audio directly to the projector to get sound 
from the built-in speaker, or you can bypass the projector ’s audio system 
and connect the audio directly from your source to a stereo or home theater 
system.You can connect the projector to most video devices that can output video. 
You cannot directly connect the coaxial cable that enters your house from a 
cable or satellite company, the signal must pass through a tuner first. Exam
-
ples of tuners are digital cable boxes, VCRs, digital video recorders, and sat
-
ellite TV boxes. Basically, any device that can change channels is considered 
a tuner.Before connecting your projector, you should decide which aspect ratio you 
want to use. The projector ’s Aspect Ratio setting is accessed through the 
Resize button on the remote or through the projector ’s Basic Picture Menu. 
See 
page
 28 for more information.
What is Aspect Ratio?Aspect ratio is the ratio of the image width to image height. TV screens are 
usually 4:3, which is the default for this projector. HDTV and most DVDs 
are 16:9. If you’re projecting onto a screen, the size/shape of the screen may 
determine which aspect ratio to use. If you are projecting onto a blank wall, 
you don’t have the screen size restriction. What you plan to project will also 
help you choose between 4:3 and 16:9. Most TV shows are 4:3, while most 
movies are 16:9.If you have a 16:9 screen then you should select an aspect ratio of 16:9 for 
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3 
screen you should still use 16:9 for anamorphic movies or HDTV, but you 
also have the option of using either 4:3 (to fill the screen) or Native (for 
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies 
only appear correctly if the DVD player is set to output to a 16:9 television. 
4:3 screen16:9 screen
Do Not Use4:3
mode
16:9
mode
Native
mode
(NTSC
only) 
						

							13
Video device connectionsNo video cables are provided with the projector. You can order cables from 
InFocus or provide your own.Composite video connectionPlug the composite video cable’s yellow connector into the video-out con
-
nector on the video device. Plug the other yellow connector into the yellow 
Video 2 connector on the projector. Plug the white connector of a Mini-plug audio Y-cable into the left audio out 
connector on the video device and plug the red connector into the right 
audio out connector on the video device. Plug the other end of the cable into 
the Audio In Video connector on the projector.Keep in mind that video output from composite connections is not as high 
quality as S-video.S-video connectionIf your video device uses a round, four-prong S-video connector, plug an 
 
S-video cable into the S-video connector on your video device and into the 
Video 1 connector on the projector. Use the audio cable as described above.Keep in mind that S-video delivers higher quality video output than com
-
posite.VESA connectionIf your video device has a 15-pin VGA output, plug one end of the included 
computer cable into the VGA connector on your video source. This connec
-
tor may be labeled “To Monitor” on the video source. Plug the computer 
cable into the Computer 1 or Computer 2 connector on the projector. 
Component video connectionIf your HD video device has component connectors, an optional Compo
-
nent to VESA adapter can be used. Plug the component cable into the video 
device. Plug the other end of the component cable into the adapter and plug 
the adapter into the Computer 1 or Computer 2 connector. Component 
offers the highest quality video output. 
						

							14
Shutting down the projectorThe projector automatically displays a black screen after no active source is 
detected for 30 minutes. This black screen helps preserve the life of the pro
-
jector. The image returns when an active source is detected or a remote or 
keypad button is pressed.Screen Save TimeYou can make the black screen appear after a preset number of minutes by 
turning on the Screen Save Time feature in the Setup menu. See 
page
 30.
Auto Off TimeThe projector also has a Auto Off Time feature that automatically turns the 
lamp off after no active sources are detected and no user interaction with 
the projector is performed for 30 minutes. By default, this feature is off. You 
can change the length of time, see 
page
 30.
Turning off the projectorTo turn the projector off, press the Pow e r button on the remote or keypad. 
The lamp turns off and the LED blinks amber for 1 minute while the fans 
continue to run to cool the lamp. When the lamp has cooled, the LED lights 
amber and the fans stop. Unplug the power cable to completely power off 
the projector.Troubleshooting your setupIf your image appears correctly on the screen, skip to the next section. If it 
does not, troubleshoot the setup. 
The Status Indicator Panel on top of the projector indicates the state of the 
projector and can help you troubleshoot
. 
Table 2: Status indicator light behavior and meaning
Status Indicator Panel icons 
Meaning
Power, solid amberPower, blinking greenPower, solid greenPower, blinking amber
The projector is plugged in.The power button has been pressed and 
the software is initializing.The projector is on and initialized.The power button has been pressed to 
turn the projector off and the fans are 
running to cool the projector.
Thermometer
The projector is too hot. Make sure the 
vents aren’t blocked (see 
page
 20). Turn 
off the projector and wait one minute, 
then turn the projector on again. Contact 
Technical Support if the problem persists
.
Lamp
Turn off the projector and wait one 
minute, then turn the projector on again. 
If the lamp light turns on again, replace the 
lamp and reset the lamp timer. 
Wrench/Service
Turn off the projector and wait one 
minute, then turn the projector on again. 
If the service lamp turns on again, service 
is required. Visit www.infocus.com/service 
to contact Service. 
						

							15
Problem 
Solution
Result
no start up screen
plug power cord into the projector
 
press power button
correct image
only start up screen appears
press the Source button 
 
activate laptop’s external port
computer image projected
Startup
Screen
A
Startup
Screen
restart laptop
A
A 
						

							16
no computer image, just the words “Signal out of 
range” 
press the Auto Image button on keypad
computer image projected
Only my laptop’s background appears, not the 
Desktop icons 
Disable “Extend my Windows Desktop” in Control Panel>Display>Settings>Display 2 
(location varies by operating system)
Background and Desktop projected
A
Signal out of
range
Panel>Display>Settings>Advanced>Adapter
(location varies by operating system)
you may also need to set a different 
resolution on your computer, as shown
in the following problem, “image fuzzy
or cropped” adjust computer refresh rate in Control 
A
A
A
A
 
Uncheck thisoption, thenclick Apply
A
A 
						

							17
Problem 
Solution
Result
image fuzzy or cropped 
set your computer’s display resolution to the native resolution of the projector 
(Start>Settings>Control 
Panel>Display>Settings tab) 
image clear and not cropped
image not centered on screen
move projector, adjust zoom, adjust height
correct image
A
A
For a laptop,
disable laptop
monitor
or turn-on dual-
display mode
A
adjust horizontal or 
Advanced Picture vertical position in 
menu 
						

							18
Problem 
Solution
Result
image not square
adjust Keystone on keypad
square image
image not sharp
adjust Sharpness in the Basic Picture menu
correct image
image does not fit 4:3 or 16:9 screen
change aspect ratio to 4:3 or 16:9 in Basic Picture>Aspect ratio menu
correct image
ABAB
AB 
						

							19
Problem 
Solution
Result
image upside down
turn off Ceiling Mount in Setup menu
correct image
image reversed left to right
turn off Rear Project in Setup menu
correct image 
projected colors don’t match source
adjust color, tint, brightness, contrast in the Basic Picture menu
correct image
AB
AB
A
AB
COLOR
COLOR