InFocus Projector IN8606HD User Manual

IN8606HD User’s Manual 
Advanced 2 Features 
Press the Menu button to open the OSD menu. Press the  ◄► buttons to move to the  Settings 2 
menu. Press the  ▲▼ buttons to move to the  Advanced 2 menu and then press 
 (Enter) or ►. 
Press the ▲▼  buttons to move up and down in the  Advanced 2 menu. Press the  ◄► buttons to
 
enter and change setting values. 
 
ITEM DESCRIPTION 
Sleep Timer  Press the 
◄► buttons to enter and set the Sleep timer. The projector automatically 
turns off after the preset...

IN8606HD User’s Manual 
Source Filter 
Press the ENTER button to enter the  Source Filter sub menu. This sub menu allows you to enable 
and disable source inputs. 
 
ITEM DESCRIPTION 
VGA Press  the ◄►  buttons to enter and enable or disable the VGA1 source. 
Component Video  Press the ◄► buttons to enter and enable or disable the Component Video source. 
Composite Video  Press the ◄► buttons to enter and enable or disable the Composite Video source. 
S-Video Press  the ◄►  buttons to enter and enable or...

IN8606HD User’s Manual 
–36  – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in a ccordance with the regulations of your...

IN8606HD User’s Manual 
2.  Remove the lamp 
compartment cover. 
 
3.  Remove the three screws 
from the lamp module. 
4.  Lift the module handle up. 
5.  Pull firmly on the module 
handle to remove the lamp 
module. 
 
6.  Reverse steps 1 to 5 to 
install the new lamp 
module.  
While installing, align the 
lamp module with the 
connector and ensure it is 
level to avoid damage. 
Note:  
The lamp module must sit 
securely in place and the 
lamp connector must be 
connected properly before 
tightening...

IN8606HD User’s Manual 
Resetting the Lamp Timer 
After replacing the lamp, you should reset the lamp hour timer to zero. Refer to the following: 
1.  Press the MENU button to open 
the OSD menu. 
2.  Press the  ◄► buttons to move to 
the Settings 2 menu. Press the  ▼ 
button to move down to 
Advanced 1 and press enter. 
3.  Press the  ▼▲ buttons to move 
down to Lamp Hour Reset. 
4.  Press the  (Enter) or ►  button. 
A message screen appears. 
5.  Press the  ▼▲◄► buttons in 
sequence to reset the lamp...

IN8606HD User’s Manual 
– 39  – 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1. Be sure to turn off and unplug the projector at  least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Only use a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior  while cleaning, leave the projector...

IN8606HD User’s Manual 
Using the Cable Lock System and Security Bar 
 
Using the Cable Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
Note: A Cable Lock System can be purchased from InFocus  or your dealer. Refer to the information that 
comes with the lock for instructions on how to use it. 
The security lock slot corresponds to Kensington’s  MicroSaver Security System. If you have any comment, contact:...

IN8606HD User’s Manual 
– 41  – 
TROUBLESHOOTING 
Common problems and solutions 
These guidelines provide tips to deal with problem s you may encounter while using the projector. If 
the problem remains unsolved, cont act your dealer for assistance. 
After spending time troubleshooting,  the problem can often be traced to something as simple as a 
loose connection. Chec k the following before proceeding to  the problem-specific solutions. 
  Use some other electrical device to confirm that the...

IN8606HD User’s Manual 
–42  – 
LED Error Messages 
ERROR CODE MESSAGES POWER LED 
BLUE 
LAMP LED 
RED 
System initialization  Flashing OFF 
Ready to power on (Standby)  ON OFF 
System powering up Flashing OFF 
Lamp lit, normal operation  ON OFF 
Cooling Flashing OFF 
Overheating  3 blinks OFF 
Thermal break sensor error 4 blinks OFF 
Lamp failure 5 blinks ON 
Lamp temperature shut down 5 blinks 1 blink 
Short circuit in lamp output detected 5 blinks 2 blinks 
End of lamp life detected 5 blinks 3 blinks...

IN8606HD User’s Manual 
– 43  – 
Problem: The image is wider at the top or bottom (trapezoid effect)  
1.  Position the projector so it is as perpendicular to the screen as possible.  
2.  Use the  Keystone button on the remote control to correct the problem. 
Problem: The image is reversed  
Check the  Projection setting on the  Settings 1 menu of the OSD. 
Problem: The image is streaked  
1. Set the  Frequency  and Tracking  settings on the  Image->Computer menu of the OSD to 
the default settings. 
2....