InFocus Projector IN5555L User Manual

30
Using Projector Web Controls
Projector Web Controls allow you to configure and control a networked projector 
via a web browser. NOTE: Projector web pages are always displayed in English.
Configuring and Controlling the Projector via a Web Browser
Before using Projector Web Controls, your projector must be configured properly 
with your network. Consult your network administrator before connecting the 
projector to your network. Incorrect network configuration of the projector may 
cause problems on...

31
Using Projector Web Controls
Changes you make are applied immediately. 
•
T
o change a numeric setting  (e.g. Brightness): Click the corresponding up 
or down button.
• T
o perform a command  (e.g. Source): Click the corresponding button.
Controls Menu
Source/General Submenu: allows you to change the video source, turn the 
projector on or put it into  standby, open and close th e shutter, and set the projec -
tor control to network or RS232 control.
Image Settings Submenu:  allows you to adjust...

32
Edge Blend Submenu: allows you to adjust edge blend, blend width, black level 
uplift and black level uplift.
Advanced Control Submenu:  allows you to adjust the color temperature, 
color offset and color gain of the projector.
Configuration Menu
IP Configuration Submenu:  allows you to manually enter the IP address con -
figuration for your projector. Cons ult with your network administrator before mak -
ing any changes on this page; incorrect network configuration of the projector may 
c ause...

33
Information Submenu: displays a read-only page of projector information.To upgrade Projector Network Firmware : Upgrades the firmware for the 
projectors network features (this firmware is separate from the regular projector 
firmware). Key in the IP address follow ed by “/firmwareUpdate.htm” on the URL 
box to activate the firmware  update procedure. Follow the prompts to accomplish 
the upgrade.
Note:  DHCP 
 must be disabled or OFF in order for the /firmwareUpdate.htm fea -
ture to work....

34
Maintenance
Cleaning the lens
1Turn the projector off and unplug the power cord.
2Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner d
 irectly to the lens. Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
3Lightly wipe the cleaning cloth over  the lens in a circular motion.
WARNINGS:  
• Turn the projector off and unplug power cord before cleaning any part of the  pr
 ojector.
• Do not...

35
1
Turn the projector off and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly.
3Remove the lamp doors by loosening 2 ca
ptive screws on each lamp door and 
pulling the doors straight off being careful not to damage the ground wires 
connecting the doors to the projector. Note: Do not remove the ground wires.
4Loosen the 3 captive shoulder screws (marked by arrows) that attach the first 
lamp module to the projector. Carefully remove the lamp module. Do the same 
for...

36
Replacing the lens
This projector is shipped without a lens. You can order a lens from 
www.infocus.com (in select areas), your retailer or your dealer.
1Turn the projector off and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3If a lens is not attached, remove the dust  cap from the projector and go to Step 
6. 
4If a lens is attached, press and hold th e release button located near the lens 
(marked “Press: Release lens”) to release the lock.
5Twist the lens...

37
Replacing the filters
It is recommended that you clean the filters every 250 hours (or as needed 
depending on your room environment) and replace the filters at the same time as 
you replace the lamps. Follow the instructions below.
1Turn the projector off and unplug the power cord. Wait 60 minutes to allow the 
projector to cool thoroughly. 
2Press the release levers on the filter cover (located on the front corner of the 
projector) and swing the cover to remove it. Repeat for the filter cover...

38
Replacing the color wheel
The color wheel of your projector is user replaceable. The color wheel which was 
installed by the factory is designed for maximum color brightness and has 6 color 
segments (RYGCWB). The optional color wheel which came as an accessory is 
designed for fully saturated color and contains 6 color segments (RGBCMY). Follow 
the instructions below to replace your color wheel.
1Turn the projector off and unplug the power cord.
2Wait 60 minutes to allow the projector to cool...

39
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the 
information that came with the lock for instructions on how to use it.
Security lock