InFocus Projector IN5102/IN5104/IN5106 User Manual

							20
Lamp won’t turn on, Temp light is lit (page 15)Make sure vents aren’t blocked; allow 
projector to cool for one minute Unplug projector; wait 20 minutes; plug in 
projector and turn it on: lamp lights
Lamp won’t turn on, Lamp light is lit (page 15)Lamp may need to be replaced (page 36)
Lamp turns on
Temperature light
 
startup
screen
Lamp light
startup
screen 
						

							21 Still having problems?
If you need assistance, visit our website or call us. See the inside of the back cover for a list of all relevant web addresses.
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we 
recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its 
full value.Image not centered on screenMove projector, adjust zoom or lens shift, 
adjust heightCorrect image
Adjust horizontal or vertical position in 
Picture>Advanced menu 
						

							22
Using the keypad buttonspower–turns the projector on (page 10) and off (page 15).
menu–opens the on-screen menus (page 27).
up/down arrows–navigates to and adjusts settings in the menus (page 27).
select–confirms choices made in the menus (page 27).
source–switches among active sources 
						

							23
Using the remote control The remote uses two (2) provided AAA batteries (Hitachi Maxell, part num-
ber LR03). They are easily installed by sliding the cover off the remotes 
back, aligning the + and - ends of the batteries, sliding them into place, and 
then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not 
at the computer). The range of optimum operation is about 16 feet (5m).For 
best results, aim the remote directly at the projector.
To use the laser pointer, press and hold the Laser button. The laser turns off 
when the button is released, or times out after two (2) minutes of continu-
ous operation.
WA R N I N G: Do not look into the laser beam emitted from the top of the 
remote control.
The remote contains four Source buttons that allow you to assign a particu-
lar input to a specific source. Simply press the numbered Source buttons to 
travel to whatever four sources you wish to have available. 
Press the remotes Menu button to open the projectors menu system. Use 
the arrow buttons to navigate, and the Select button to select features and 
adjust values in the menus. 
The remote also has a power button to turn the projector on and off, volume 
buttons and a mute button to control the sound, a backlight button to light 
the remotes buttons in the dark, and a video and computer button to switch 
between those two sources.
Two presentation-specific features are also provided. Use the blank button 
to display a blank screen instead of the current slide; use the effect button to 
invoke a user-definable action, such as freeze, PiP, or magnify.
The Auto Image button reacquires the computer image and the Presets but-
ton lets you customize the settings for each source. Up to three Preset set-
tings can be customized and saved.
Troubleshooting the remote Make sure the batteries are installed in the proper orientation and are 
not dead. The LED at the top of the remote lights when any button is 
pressed when the battery power is adequate.
 Make sure you’re pointing the remote at the projector, not the com-
puter, and are within the remote range of 16 feet (5m).
backlight button
navigation buttons
LED
source buttons
laser
button 
						

							24
Using the audio To play sound from the projector, connect your source to an Audio In con-
nector on the projector.
To adjust the volume, mute, or loudness, use the Audio menu (see page 31).Troubleshooting audioIf there is no sound, check the following:
 Make sure the audio cable is connected.
 Make sure mute isn’t active. 
 Make sure the volume is turned up enough.
 Make sure you are connected to the corresponding audio in for your 
source. By default, Audio 1 corresponds to Computer 2, Audio 2 cor-
responds to Computer 3, Audio 3 corresponds to Video 2 and 3, and 
Audio 4 corresponds to Video 1. You can change these assignments, 
see page 31.
 Adjust the audio source.
 If playing a video, make sure the playback has not been paused.Connecting external speakersThe projector can be attached to external speakers that have their own 
power source by plugging a speaker cable into the projector ’s Audio Out 
connector. 
connect audio cable
adjust volume
external speakersspeaker
cable 
						

							25
Optimizing computer imagesAfter your computer is connected properly and the computer ’s image is on 
the screen, you can optimize the image using the onscreen menus. For gen-
eral information on using the menus, see page 27.
 Adjust the Keystone, Contrast, or Brightness in the Picture menu. 
 Change the Aspect Ratio. Aspect Ratio is the ratio of the image width to 
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV 
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your 
input source. See page 28 for details.
 Adjust the Color Temperature in the Advanced menu.
 Adjust the Phase, Tracking, or Horizontal or Vertical position in the 
Advanced menu.
 Once you have optimized the image for a particular source, you can 
save the settings using Presets. This allows you to quickly recall these 
settings later. See page 29.
Presentation featuresSeveral features are provided to make giving presentation easier. The fol-
lowing is an overview, details are found in the menu section on page 27.
The Custom key, available on several optional remotes only, allows 
you to assign various features to the key. The default effect is Source 
Info. You can select from Blank, Mute, AV Mute, Aspect Ratio, Source, 
Auto Image, Freeze, Magnify, Source Info, and Service Info. See page 33 
for details. 
 The Freeze effect allows you to freeze the displayed image. This is use-
ful if you want to make changes on your computer without your audi-
ence seeing them. 
 The Startup Logo menu option lets you change the default startup 
screen to a black, white, blue, or a custom logo screen via Capture New. 
See page 32.
 Two menu options, Power Save and Screen Save, are provided to auto-
matically shut down the projector after several minutes of inactivity or 
display a blank screen. This helps preserve lamp life. See page 32.
 A Low Power menu option is also available to help lower the projec-
tor ’s fan sound volume. See page 31. 
						

							26
Optimizing video imagesAfter the video device is connected properly and the image is on the screen, 
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 27.
 Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture 
menu. See page 28. 
 Change the Aspect ratio. Aspect ratio is the ratio of the image width to 
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV 
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your 
input source. See page 28.
 Select a Sharpness setting. See page 29.
 Adjust the Color Temperature. Select a listed value, or select User and 
individually adjust the intensity of the red, green, and blue color. See 
page 29.
Customizing the projectorYou can customize the projector for your specific setup and needs. See 
page 31 to page 34 for details on these features.
 For rear projection, turn Rear mode on in the Settings>System menu.
 For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu. 
 Specify which source the projector checks first for an active signal dur-
ing power-up. 
 Turn the projector ’s on-screen display messages on and off.
 Turn on power saving features. 
 Specify blank screen colors and startup logos.
 Specify the menu language.
 Control your projector using RS232 commands. See page 9 and page 42.
 Customize the projector for your specific installation using optional 
long or short throw lenses. See the inside back cover of this User ’s 
Guide for ordering information. 
						

							27
Using the menusTo open the menus, press the menu button on the keypad or remote. (The 
menus automatically close after 60 seconds if no buttons are pressed.) The 
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button. 
To change a menu setting, highlight it, press Select, then use the up and 
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm 
your changes. Use the arrows to navigate to another setting. When your 
adjustments are complete, navigate to Previous, then press Select to go to 
the previous menu; press the Menu button at any time to close the menus. 
Dots appear before the menu name. The number of dots indicate the menu’s 
level, ranging from one (the Main menu) to five (the most nested menus). 
The menus are grouped by usage:
 The Picture menu provides image adjustments.
 The Settings menu provides set-up type adjustments that are not 
changed often.
 The Source Info menu provides a read-only display of information 
about the projector and source. 
Certain menu items may be grayed out until a particular source is con-
nected. For example, Tint is only available for video sources and will be hid-
den when a computer source is active. Other menu items may be grayed out 
when they are not available. For example, Brightness is grayed out until an 
image is active.
Keypad navigation 
buttons
Main menuMenu
button
 
 
PictureSettings
menu DotsmenuSource Info menu 
						

							28
Picture menuTo adjust the following six settings, highlight the setting, press Select, use 
the up and down arrows to adjust the values, then press select to confirm 
the changes.
Ke y s t o n e  Ve r t i c a l: adjusts the image vertically and makes a squarer image 
by using an adjustable scale band. 
Ke y s t o n e  H o r i zo n t a l: adjusts the image horizontally and makes a squarer 
image by using an adjustable scale band.
Contrast: controls the degree of difference between the lightest and darkest 
parts of the picture and changes the amount of black and white in the 
image.
Brightness: changes the intensity of the image.
Color: (Computer 1 and video sources only) adjusts a video image from 
black and white to fully saturated color.
Tint: (Computer 1 and NTSC video sources only) adjusts the red-green 
color balance in the image.
Auto Image: resynchs the projector to the source.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. 
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are 
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or 
down to fill the display area.
increasing keystone Keystone Vertical
decreasing keystone
Keystone Horizontal
Aspect Ratio 
						

							29
Presets: Presets are provided that optimize the projector for displaying 
computer presentations and video images in different lighting conditions 
and on different backgrounds. 
There are also user-definable presets. To set a preset for the current source, 
adjust the image, select Save Settings in the Presets menu, then select Save 
User Presets 1 (or 2 or 3). You can recall these settings in the future by select-
ing the User 1 preset. If you select User Presets then further adjust the 
image, Presets Off will automatically be selected in the Preset menu to indi-
cate changes have been made. 
To restore the factory default settings, choose Factory Reset in the Set-
tings>Service menu. Advanced settingsSharpness: changes the clarity of the edges of a video image. Select a sharp-
ness setting.
Color Space: This option applies to computer and component video 
sources (except 480i/576i). It allows you to select a color space that has been 
specifically tuned for the input signal. When Auto is selected, the projector 
automatically determines the standard. To choose a different setting, turn 
off Auto, then choose RGB for computer sources, RGB Video for HDMI 
computer sources, and either REC709 or REC601 for component video 
sources.
Color Temperature: changes the intensity of the colors. Select a listed 
value, or select User and individually adjust the intensity of the red, green, 
and blue colors.
PresetsSave Settings
  
Sharpness
 
Color Space
Color Temperature