InFocus Projector IN5100 User Manual
Here you can view all the pages of manual InFocus Projector IN5100 User Manual. The InFocus manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 2
1 Declaration of Conformity Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 97223 USA We declare under our sole responsibility that this projector conform to the following dire ctives and norms: EMC Directive 2004/108/EC EMC: EN 55022 EN 55024 EN 61000-3-2 EN 61000-3-3 Low Voltage Directive 2006/95/EC Safety: IEC 60950-1: 1 st Edition Trademarks Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple...
Page 3
WARNING: Do not look into laser beam emitted from the front of the remote control. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Class 2 Laser product; maximum output 1mW; wavelength 650nm. [Class 2 Laser Product] Wavelength 650nm; Maximum output 1mW; No beam divergence. [Laser Diode] Wave length 650nm; Maximum power 7mW; Beam diver- gence 33deg (perpendicular)/8deg (parallel). Location of...
Page 4
3 Table of Contents Introduction 5 Included Items 5 Positioning the projector 7 Connecting a computer 8 Required computer connections 8 Displaying a computer image 10 Adjusting the image 11 Connecting a video device 12 Displaying a video image 13 Shutting down the projector 15 Troubleshooting your setup 15 Using the keypad buttons 22 Using the remote control 23 Using the audio 24 Optimizing computer images 25 Presentation features 25 Optimizing video images 26 Customizing the projector...
Page 5
4 Important Operating Considerations for Safety • Place the projector in a horizontal position no greater than 8 degrees off axis. • Locate the projector in a well-ventilated are a without any obstructions to intake or exhaust vents. Do not pl ace the projector on a tablecloth or other soft covering that may block the vents. • Locate the projector at least 4 (1.2 m) away from any heating or cooling vents. • Use only approved ceiling mounts. • Warning: To prevent eye injury if the projector is...
Page 6
5 Introduction Your new multimedia projector provides three computer, three video, and four audio inputs, one audio output, and RS-232 and Network control. It has WUXGA 1920 x 1200 resolution. The projec tor is easy to connect, easy to use, and easy to maintain. Product specifications To read the latest specifications on your multimedia projector, be sure to visit our website. Web address information is located on the back inside cover of this User’s Guide. Online Registration Register your...
Page 7
6 Connector Panel The projector provides three computer and three video connection options: •one VGA computer • one HDMI™ (High Definition Multimedia Interface)* • one component BNC (G/Y, B/C B/PB, R/CR/PR, H, V) • one component RCA video (Pr, Pb, Y) •one S-video •one composite RCA video The projector provides computer and video co nnectors for audio support: • two composite RCA stereo audio (L, R) • one audio out •two audio ins The projector also provides the following connectors: • one wired...
Page 8
7 Positioning the projector To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your eq uipment. Here are some general guide- lines: • Position the projector on a flat surfac e at a ri ght angle to the screen. The projector must be at least 3 feet (0.9m) from the projection screen. • Position the projector within 10 feet (3m) of your power source and with in 6 feet...
Page 9
8 Connecting a computer Required computer connections Connect one end of the VGA computer cable to the Computer 2 connector on the projector. Connect the other end to the video port on your computer. If you are using a desktop computer, yo u first need to disconnect the moni- tor cable from the computer’s video port. Connect the black power cable to the co nnec tor on the back of the projector and to your electrical outlet. NOTE : Always use the power cable that shipped with the projector....
Page 10
9 If you are using a desktop computer and want to see the image on your computer screen as well as on the projection screen, plug the monitor cable to the Monitor out connector on the projector. You can control the projector from an LCD control panel, touch screen, or other control device or computer by connecting an RS-232 cable to the pro- jector’s Serial Control connec tor. Specific RS-232 commands can be found in the Service and Support section of our website and in the Appendix....