InFocus Projector IN34 User Manual

IN32/IN34Reference Guide 

1
Declaration of ConformityManufacturer: InFocus Corporation, 27700B SW Parkway Avenue, Wilsonville, 
 
Oregon 97070 USA
 
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
 
We declare under our sole responsibility that this projector conforms to the following 
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
 
EMC: EN 55022
 
           EN 55024
 
 EN 61000-3-2
 
 EN 61000-3-3
 
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
 
Safety: IEC 60950-1: 1
st...

2
Table of Contents 
Introduction 3
Connecting a computer  5
Required computer connections  5
Displaying a computer image  7
Adjusting the image  8
Connecting a video device   9
Displaying a video image  10
Shutting down the projector  12
Troubleshooting your setup  12
Using the keypad buttons  20
Using the remote control  21
Using the audio  22
Optimizing computer images  23
Presentation features  23
Optimizing video images  23
Customizing the projector  23
Using the menus  24
Picture menu  25
Settings...

3
IntroductionYour new digital projector provides computer and video inputs and has 
XGA 1024x768 resolution. The projector is easy to connect, easy to use, and 
easy to maintain. Product specificationsTo read the latest specifications on your multimedia projector, be sure to 
visit our website at www.infocus.com, as specifications are subject to 
change. AccessoriesThe standard accessories that came with your projector are listed in the 
included user ’s guide. Optional accessories can be found on our...

4
Connector PanelThe projector provides computer and video connectors:  one M1-D/A (HD, DVI, and computer) one VESA (HD, HD component, and computer) one VESA (monitor out) one S-video one composite RCA video one audio in/one audio outIt also has an RJ-45 connector for serial control. The Command Line Inter
-
face (CLI) specifications and commands are on our website.
Connector panel 
 
lock
power
connector M1-D/A
s-video composite
external
speaker
(audio out) RJ-45 serial control
video
computer...

5
Connecting a computerRequired computer connectionsConnect the black end of the computer cable to the Computer 1 connector 
on the projector. Connect the blue end to the video port on your computer. If 
you are using a desktop computer, you first need to disconnect the monitor 
cable from the computer ’s video port. 
 
Some Macintosh® computers do not have a standard VESA-out video port. 
If the supplied computer cable will not connect to your computer, purchase 
the appropriate adapter from your Apple®...

6
If you are using a desktop computer and want to see the image on your 
computer screen as well as on the projection screen, plug the monitor cable 
to the Monitor Out connector on the projector. If you prefer connecting your projector to your computer with an optional 
VESA cable, connect one end of the cable to the VESA port on your com
-
puter, and connect the other end of the cable to the blue Computer 2 con
-
nector on the projector. You can control the projector from an LCD control panel or...

7
Displaying a computer image Remove the lens cap.
 
    Press the Pow e r button on the top of the projector or the remote.The Power light on the Status Indicator Panel (
page
 12) blinks green and the 
fans start to run. When the lamp comes on, the start up screen displays and 
the Power light is steady green. It can take a minute for the image to achieve 
full brightness. 
? No startup screen? Get help on 
page
 13. 
Turn on your computer.The computer ’s image should appear on the projection screen....

8
Adjusting the imageAdjust the height of the projector, if necessary, by pressing the release but
-
ton to extend the elevator foot. Rotate the leveling foot (located at the bottom back right corner), if neces
-
sary.
 
Position the projector the desired distance from the screen, so that the lens is 
perpendicular to the screen. See 
page
 36 for a table listing screen sizes and distances.
 
    Adjust the zoom or focus rings by rotating them until the desired image size 
and focus are produced....

9
Connecting a video device No video or audio cables are included with your projector.If the video device uses a round, four-prong S-video connector, plug an 
 
S-video cable into that connector on the video device and into the Video 2 
connector on the projector. If the device uses a composite video connector, 
plug a composite video cable into that connector on the video device and 
into the Video 1 connector on the projector. For audio, plug a mini-plug audio Y-cable
 into the Audio in connector on...