InFocus Projector IN3136a User Manual

							— 24 — 
Color Manager 
Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Image menu. 
Press the ▼▲ buttons to move to the Color Manager menu and then press  (Enter) or ►. Press 
the ▼▲ buttons to move up and down in the Color Manager menu.  
 
ITEM DESCRIPTION 
Red Select to enter the Red Color Manager.  
Press the ◄► buttons to adjust the Hue, Saturation, and Gain. 
Green Select to enter the Green Color Manager.  
Press the ◄► buttons to adjust the Hue, Saturation, and Gain. 
Blue Select to enter the Blue Color Manager.  
Press the ◄► buttons to adjust the Hue, Saturation, and Gain. 
Cyan Select to enter the Cyan Color Manager.  
Press the ◄► buttons to adjust the Hue, Saturation, and GainK 
Magenta Select to enter the Magenta Color Manager.  
Press the ◄► buttons to adjust the Hue, Saturation, and Gain. 
Yellow Select to enter the Yellow Color Manager.  
Press the◄► buttons to adjust the Hue, Saturation, and Gain. 
White Select to enter the White Color Manager.  
Press the ◄► buttons to adjust the Red, Green, and BlueK 
 
   
						

							— 25 — 
Settings 1 Menu  
Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 
menu. Press the ▲▼ buttons to move up and down in the Settings 1 menu. Press the ◄► buttons 
to enter and change setting values. 
 
ITEM DESCRIPTION 
Source Press the ◄► buttons to enter and select a source. 
Projection Press the ◄► buttons to enter and choose from four projection methodsK 
Aspect Ratio Press the ◄► buttons to enter and adjust the video aspect ratio. 
Keystone Press the ◄► buttons to enter and adjust the display keystone. 
Digital Zoom  Press the ◄► buttons to enter and adjust the Digital Zoom menu.  
Audio Press  (Enter) or ► to enter the Audio menu. See Audio on page 26. 
Advanced 1 Press  (Enter) or ► to enter the Advanced 1 menu. See Advanced 1 Features on 
page 27. 
Advanced 2 Press  (Enter) or ► to enter the Advanced 2 menu. See Advanced 2 Features on 
page 29. 
     
						

							— 26 — 
Audio 
Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 
menu. Press the ▼▲ buttons to move to the Audio menu and then press  (Enter) or ►. Press the 
▼▲ buttons to move up and down in the Audio menu. 
 
ITEM DESCRIPTION 
Volume Press the ◄► buttons to enter and adjust the audio volume.  
Mute Press the ◄► buttons to enter and turn on or off the speaker. 
   
						

							— 27 — 
Advanced 1 Features 
Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 
menu. Press the ▲▼ buttons to move to the Advanced 1 menu and then press  (Enter) or ►. 
Press the ▲▼ buttons to move up and down in the Advanced 1 menu. Press the ◄► buttons to 
enter and change setting values. 
 
ITEM DESCRIPTION 
Language Press the ◄► buttons to enter and select a different localization MenuK 
Security Lock  Press the ◄► buttons to enter and enable or disable the security lock functionK 
Blank Screen Press the ◄► buttons to enter and select a different color to blank the screen. 
Closed Captioning Press the ◄► buttons to enter and enable or disable Closed Captioning 
3D Setting Press  (Enter) or ► to enter the 3D menu. See page 28 for more information on the 
3D Setting. 
Keypad Lock Press ◄► to enter and enable or disable the keypad keys. 
Note:  
To enjoy the 3D function, first enable the Play Movie in 3D setting found in your DVD device under the 
3D Disc Menu. 
    
						

							— 28 — 
3D Setting 
 
ITEM DESCRIPTION 
3D Press the ◄► buttons to enter and select different 3D modesK 
3D Sync Invert Press the ◄► buttons to enter and enable or disable 3D Sync InvertK 
3D Format Press the ◄► buttons to enter and enable or disable different 3D formatsK 
 
Note: 
1. By default, if no 3D source is detected, the 3D OSD menu items will not be available. 
2. When the projector is connected to an appropriate 3D source, the 3D OSD menu items are available 
for selection. 
3. Use 3D glasses to view a 3D image. 
4. You need 3D content from a 3D DVD or 3D media file. 
5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature). 
6. You need DLP link 3D glasses. 
7. The OSD 3D mode needs to match the type of glasses (DLP link). 
8. Power on the glasses. Glasses normally have a power on -off switch.  
Each type of glasses has their own configuration instructions. Please follow the configuration 
instructions that come with your glasses to finish the setup process. 
  
						

							— 29 — 
Advanced 2 Features 
Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 
menu. Press the ▲▼ buttons to move to the Advanced 2 menu and then press  (Enter) or ►. 
Press the ▲▼ buttons to move up and down in the Advanced 2 menu. Press the ◄► buttons to 
enter and change setting values. 
 
ITEM DESCRIPTION 
Test Pattern Press the ◄► buttons to enter and select internal test patternK 
H Image Shift Press the ◄► buttons to enter and select H Image ShiftK 
V Image Shift Press the ◄► buttons to enter and select V Image ShiftK 
   
						

							— 30 — 
Settings 2 Menu  
Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Settings 2 
menu. Press the ▲▼ buttons to move up and down in the Settings 2 menu.  
 
ITEM DESCRIPTION 
Auto Source Press the ◄► buttons to enter and enable or disable automatic source detection.  
No Signal Power 
Off (min.) 
Press the ◄► buttons to enter and enable or disable automatic shutdown of lamp 
when no signal is detectedK 
Auto Power On Press the ◄► buttons to enter and enable or disable automatic power On when AC 
power is supplied. 
Lamp Mode Press the ◄► buttons to enter and select the lamp mode for higher brightness, or 
lower brightness if you wish to save lamp lifeK 
Reset All Press  (Enter) or ► to reset all settings to default values. 
Status Press  (Enter) or ► to enter the Status menu. See page 31 for more information on 
Status. 
Advanced 1 Press  (Enter) or ► to enter the Advanced 1 menu. See Advanced 1 Features on 
page 32. 
Advanced 2 Press  (Enter) or ► to enter the Advanced 2 menu. See Advanced 2 Features on 
page 41. 
Note:  
“Dynamic ECO”: Press the Blank button to activate the Dynamic ECO feature, which will dim the lamp 
30% when the image is black. 
      
						

							— 31 — 
Status 
Press the ▲▼ buttons to move up and down in the Settings 2 menu. Select the Status menu and 
press  (Enter) or ► to enter. 
 
ITEM DESCRIPTION 
Active Source Displays the current active source type. 
Video Information Displays resolution/video information for RGB sources and color standard for Video 
sources. 
Lamp Hours Lamp hour usage information is displayed. (Eco, Normal and Dynamic Eco) 
Serial Number Displays serial number of product. 
Software version Displays system software version. 
   
						

							— 
32  —   Advanced 
1 Features  Press the 
Menu button to open the OSD menu. Press the  ◄► buttons to move to the  Settings 2 
menu. Press the  ▲▼
 buttons to move to the  Advanced 1 menu and then press   (Enter)  or ►. 
Press the  ▲▼ buttons to move up and down in the  Advanced 1 menu. Press the ◄► buttons  to 
enter and change setting values.  I TEM   D ESCRIPTION  
Menu Position   Press  the  ◄►   button s   to   enter and   select different OSD location.  
Translucent Menu   Press  the  ◄►   button s   to   enter and   select OSD background translucent level. 
Low Power Mode   Press  the  ◄►   button s   to   enter and   turn Low Power Mode  Off, On, On by Lan.  
Fan Speed   Press the ◄► button s   to   enter   and   toggle between Normal and High fan speeds.    
Note : We recommend selecting high speed in high temperatures, high humidity, or 
high altitude   ( higher than  1500m/4921ft)   areas.  
Lamp Hour Reset   After replacing the lamp,  the lamp   should be reset. See page  33   for more information 
on   Lamp Hour Reset .  
Projector ID  Press  the  ◄►   button s   to   enter and   adjust  the   two digit projector ID from  0 0 through 
9 8 .  
Network   Press    (Enter)  or   ► to enter the Network menu. See page  33   for more information 
on   Network .  
Note:
   
When 
On by 
Lan is enabled, VGA Out is inactive when the projector is in standby mode.     
						

							— 
33  —   Lamp Hour Reset 
Please refer to 
Resetting the Lamp Timer  on page 45 to reset the lamp hour counter.  Network 
I TEM   D ESCRIPTION  
Network State   Displays the  n etwork connection status.  
DHCP   Press ◄► to turn DHCP On or Off.  
Note:   If  DHCP is turned Off , complete the IP Address, Subnet Mask, Gateway, and 
DNS fields.  
IP Address  Enter a valid IP address  when   DHCP is turned off.  
Subnet Mask   Enter a valid Subnet Mask  when   DHCP is turned off.  
Gateway   Enter a valid Gateway address  when   DHCP is turned off.  
DNS   Enter a valid DNS name  when   DHCP is turned off.  
Apply   Press    (Enter)  or   ►   to confirm settings.