InFocus Projector IN3134a User Manual

							— 14 — 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Ensure the cables are in a safe location. You could trip over them.  
 
To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired 
angle has been achieved. 
 
 
 
    
						

							— 15 — 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom  
control (on the projector 
only) to resize the 
projected image and 
screen size . 
 
2.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image . 
3.  Use the KEYSTONE 
buttons on the remote 
control to correct 
trapezoid image issues 
(wider top or bottom). 
 
4.  The keystone control 
appears on the display.  
Adjusting the Volume 
1.  Press the Volume +/- 
buttons on the remote 
control.  
The volume control 
appears on the display. 
 
 
2.  Press the MUTE button 
on the remote control to 
turn off the volume. 
       
						

							— 16 — 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control arrow buttons to navigate and make changes to the OSD.  
 
1. To enter the OSD, press the 
MENU button.  
2. There are three menus. 
Press the ◄► buttons to 
move through the menus.  
3. Press the ▲▼ buttons to 
move up and down in a 
menu.  
4. Press the ◄► buttons to 
change setting values. 
5. Press the MENU button to 
close the OSD or leave a 
submenu. 
 
Note: 
Depending on the video source, not all items in the OSD are available. For example, the 
Horizontal/Vertical Position items in the Computer menu can only be modified when connected 
to a PC. Items that are not available cannot be accessed and are grayed out.  
 312645
78
1
2
2
3
3
4
5
6
6
7
7
8  
						

							— 17 — 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the ◄► buttons to navigate to Settings 1. Press the ▲▼ 
buttons to move to the Advanced 1 menu. 
 
2. Press  (Enter) or ► to enter the Advanced 1 sub menu. Press the ▲▼ buttons until 
Language is highlighted.  
 
3. Press the arrow buttons until the language you want is highlighted.  
4. Press the MENU button four times to close the OSD.   
   
						

							— 18 — 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
MAIN 
MENU 
 
SUB MENU   
 
SETTINGS 
Image  Display Mode    Presentation, Bright, Game, 
Movie, TV, sRGB, Blackboard, 
User 
  Brightness    0~100 
  Contrast    0~100 
  Computer  Horizontal Position  -5~5 (depend on Autolock) 
    Vertical Position  -5~5 (depend on Autolock) 
    Frequency  0~31 
    Tracking  -5~5 
  Auto Image     
  Advanced  Brilliant Color  0~10 
    Sharpness  0~31 
    Gamma  1.8, 2.0, 2.2, 2.4, B&W, Linear 
    Color Temperature  Warm, Normal, Cold 
    Video AGC  Off, On 
    Video Saturation  0~100 
    Video Tint  0~100 
  Color Manager  Red Hue, Saturation, Gain 0~100 
    Green Hue, Saturation, Gain 0~100 
    Blue Hue, Saturation, Gain 0~100 
    Cyan Hue, Saturation, Gain 0~100 
    Magenta Hue, Saturation, Gain 0~100 
    Yellow Hue, Saturation, Gain 0~100 
    White Red, Green, Blue 0~100 
  
						

							— 
19  —   M AIN
M ENU   S UB  M ENU   S ETTINGS  
S ettings 1     Source   Source   reference Input Source Select (IR/Keypad)  
Projection   Normal, Real, Ceiling, Real+Ceiling  
Aspect Ratio   Fill, 4:3, 16:9, Letter Box, Native, 2.35:1  
Keystone   - 40~40  
Digital Zoom   - 10~10  
Audio   Volume   0 ~10  
Mute   Off, On  
Advanced 1   Language   English, Français, Deutsch, Españ ol, 
Portuguê s,  簡体中文 ,  繁體中文 , Italiano, 
Norsk, Svenska, Nederlands,  Русский, 
Polski, Suomi,  Ελληνικά,  한국어 ,  Magyar, 
Čeština,  ةيبرعلا , Tü rkçe, Vi ệ t,  日本語 ,  ไทย , 
یسراف ,  תירבע , Bahasa Indonesia  
Security Lock   Off, On  
Blank Screen   Blank, Red, Green, Blue, White  
Closed Captioning   Off, On  
3D Setting   3D   Off, DLP - Link, IR  
3D Sync Invert   Off, On  
3D Format   Frame  Sequential , Top/Bottom,  Side - By -
Side, Frame  Packing   (3D Frame   Packing 
HDMI source only)  
Keypad Lock   Off, On  
Advanced 2   Test Pattern   None, Grid, White, Red, Green, Blue, 
Black  
H Image Shift  - 50~50  
V Image Shift   - 50~50   
						

							— 20 — 
MAIN 
MENU 
 
SUB MENU   
 
SETTINGS 
Settings 2  Auto Source    Off, On 
  No Signal 
Power Off 
   0~180 
  Auto Power 
On 
   Off, On 
  Lamp Mode    ECO , Normal, Dynamic ECO 
  Reset All     
  Status  Active Source   
    Video Information   
    Lamp Hours(ECO, Normal, 
Dynamic ECO) 
  
    Serial Number   
    Software Version   
  Advanced 1  Menu Position  Center, Down, Up, Left, Right 
    Translucent Menu  0%, 20%, 40%, 60%, 80% 
    Low Power Mode  Off, On, On By Lan 
    Fan Speed  Normal, High 
    Lamp Hour Reset   
    Projector ID  0-98 
    Network Network State Connect, Disconnect 
     DHCP On, Off 
     IP Address  0~255, 0~255, 0~255. 0~255 
     Subnet Mask 0~255, 0~255, 0~255. 0~255 
     Gateway 0~255, 0~255, 0~255. 0~255 
     DNS 0~255, 0~255, 0~255. 0~255 
     Apply Ok / Cancel 
  Advanced 2  Sleep Timer  0~600 
    Source Filter HDMI1/MHL Disable, Enable 
     HDMI2 Disable, Enable 
     VGA1 Disable, Enable 
     VGA2 Disable, Enable 
     S-Video Disable, Enable 
     Composite Video Disable, Enable 
  
						

							— 21 — 
Image Menu  
 Attention ! 
When image options are changed, the Display Mode changes to User. 
Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Image Menu. 
Press the ▲▼ buttons to move up and down in the Image menu. Press the ◄► buttons to enter and 
change setting values. 
 
ITEM DESCRIPTION 
Display Mode 
Press the ◄► buttons to enter and set the Display Mode.  
Note: Display Mode must be set to User in order to access the other Image menu 
items. 
Brightness Press the ◄► buttons to enter and adjust the display brightnessK 
Contrast Press the ◄► buttons to enter and adjust the display contrastK 
Computer Press  (Enter) or ► to enter the Computer menu. See Computer Menu on page 
22. 
Auto Image Press  (Enter) or ► to automatically adjustment for phase, tracking, size and 
positionK 
Advanced Press  (Enter) or ► to enter the Advanced menu. See Advanced Feature on page 
23. 
Color Manager Press  (Enter) or ► to enter the color manager menu. See page 24 for more 
information on Color Manager.       
						

							— 22 — 
Computer Menu 
Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Image menu. 
Press the ▲▼ buttons to move to the Computer menu and then press  (Enter) or ►. Press the 
▲▼ buttons to move up and down in the Computer menu. 
 
ITEM DESCRIPTION 
Horizontal Position Press the ◄► buttons to enter and adjust the display position to left or right.  
Vertical Position Press the ◄► buttons to enter and adjust the display position to up or down.  
Frequency Press the ◄► buttons to enter and adjust the A/D sampling clock. 
Tracking Press the ◄► buttons to enter and adjust the A/D sampling dot. 
   
						

							— 23 — 
Advanced Features 
Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Image menu. 
Press the ▼▲ buttons to move to the Advanced menu and then press  (Enter) or ►. Press the 
▼▲ buttons to move up and down in the Advanced menu. 
 
ITEM DESCRIPTION 
Brilliant Color Press the ◄► buttons to enter and adjust the Brilliant Color valueK 
Sharpness Press the ◄► buttons to enter and adjust the display sharpnessK 
Gamma Press the ◄► buttons to enter and adjust the gamma correction of the displayK 
Color Temperature Press the ◄► buttons to enter and adjust the color temperature. 
Video AGC Press the ◄► buttons to enter and enable or disable the Automatic Gain Control for 
video sourceK 
Video Saturation Press the ◄► buttons to enter and adjust the video saturation. 
Video Tint Press the ◄► buttons to enter and adjust the video tint/hue.