InFocus Projector IN3128HD User Manual

30
Wireless connection
To connect to the projector wirelessly, you have to plug an InFocus wireless 
dongle (optional) to the USB Type A connector on the projector, and then only a 
few OSD configuration steps are required.
1Make sure the projector is turned on.
2Press 
Menu on the keypad or remote and then go to  Advanced Menu > Setup  
>  Network > Wireless LAN  menu.
3Make sure the Status is Connect .
4Make sure the  SSID information is displayed.
5In AP  mode, you need to use your computer’s...

31
iii. The Crestron (eControl) page displays the Crestron eControl user inter-
face. See page 31 for details.
3To access the Admin page, enter the password. The default password is 
“admin”. If you forget the password, please go to Advanced Menu > Setup > 
Network > Network Restart to restore the password to the default code.
•System Status:  Displays the system information.
• General Setup:  Allows you to turn on/off the projector, switch the input 
signal for the projector, and change  the password...

iiiii
i
32
i. This area is only used with a Crestron Control System. Please contact Cre-ston or refer to the Crestron user manual for setup information.
ii. This area is used for naming the projector, associating it with a particular location, assigning a responsible party  to it, and adjusting network settings.
iii. This area is used to set User and  Admin passwords. When password protec-
tion is enabled, unauthorized changes to the projector configuration will be 
avoided.
• To prevent errors, only...

33
3The Info page displays the information and status of this projector.
Press  exit to go back to the Crestron remote network operation page.
4After pressing the  Help button, the  Help Desk window will display in the 
upper right corner of the screen. Yo u will be able to send messages to 
RoomView™
 software administrato rs/users who are connected to the same 
local area network.
 
• For more information, visit  http://www.crestron.com and 
www.crestron.com/getroomview .
Crestron RoomView
From the...

34
Displaying images through ifPresenter
Downloading and installing ifPresenter
The ifPresenter is an application which can run on the host PC. It helps connect 
your computer to an available network projector and transfer the desktop content 
to the network projector via local network connection.
1Enter the main page of Network Control. See steps 1-2 on page 30 for details.
2Download ifPresenter.
3When the download is complete, install the software to your computer by 
clicking the exe file. Follow the...

35
4The Basic Setting page allows you to configure ifPresenter.
i. To change the ifPresenter interface language, click the down arrow to reveal 
a drop-down list and select a desired language. Click  Apply.
ii. Users can change the size  parameters of the frame in FixedSize capture 
mode by modifying width and height on this page and click  Apply to make 
changes take effect. 
iii. User can use the mirror driver for presenter capture image, if the system has  installed the mirror driver.
iv. To allow...

36
6You can manage the connected projectors listed under Device Management.
• Under a conference mode:
1 Only the administrator can take control.
2 A projector can display up to 4 computer screens.
• You can set the name of your computer under ifPresenter Management. • For details about the icons, please see the following:7Disconnect
To disconnect from the projector(s), click the 
Disconnect icon.
• Be sure to turn off other virtual ne twork control programs before using 
ifPresenter....

37
Displaying pictures with a USB storage device
The projector has a built-in application which can display images from a USB 
storage device. It can eliminate the need for a computer source.
The projector supports the following image formats:
File formatMaximum pixel size
JPEG8000 x 8000
GIF/TIFF/PNG/BMP1280 x 800
• Progressive JPEG files are not supported.
• Some JPEG files may not display clearly.
To display images from a USB storage device:
1Plug the USB storage device into the USB Type A...

38
approximately 8 seconds. Delay 5 displays each image for approximately 13 
seconds. NOTE: The actual display time varies based on the file size.
• Slide Right/Slide Up/Right Down/XLines/YLines/Blocks:  Sets the way the 
slide show is displayed.
• Repeat On/Off:  Sets whether to repeat the slide shows.
When viewing full screen images
•Thumbnail/Display/SlideShow:  Displays the selected image(s) in Thumbnail, 
Full Screen or SlideShow mode.
• Best Fit/Actual Size:  Sets the display size of the image.
•...

39
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•Projector must be off and the lens must be at room temperature.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner 
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
•Turn the projector off and unplug power cord before cleaning any part of 
the projector.
•...