InFocus Projector IN212x User Manual

							30
To copy and paste a file or folder to another location:
1Press the Source button on either the remote or keypad.
2Navigate to LightCast and press the Select button on the remote or keypad.
3Navigate to the Local or USB directory tab that contains the item you wish to 
copy.
4Navigate to More and press Select.
5Navigate to Copy and press Select. 
6Navigate to the item you wish to copy and press Select. A green checkmark 
appears next to the selected item.
7Navigate to the Local or USB directory tab.
8Navigate to the location you wish to paste the item into and press Select.
9Navigate to Paste and press Select.  
						

							31
Using Network Features
Manage the projector from a computer using a web browser when the computer 
and the projector are properly connected to the same local area network.
Power Saving Mode must be turned Off in the Power menu for Ethernet control to 
w ork wh

en the projector is in standby.
Network Configuration
The network can be configured:
1. From the projector menu, navigate to Advanced Menu > Setup > Network.
DHCP is on by default. When connected to a network configured as a dynamic 
host all the
  IP addresses should be automatically populated. Turn DHCP off to set 
a fixed IP. Change the addresses by highlighting a configuration item and pressing 
Select. Use the up and down arrows to change the values, and the right and left 
arrows to navigate between values. Press Select when done with that item. To 
apply changes select Apply, display Yes, and press Select. 
2.  From the online menus in your browser.
Enter the IP address of the projector in Internet Explorer. Enter the default 
Admi nistrato r pass

word 0000 in the top menu.
  Click Network Settings to access the network configuration panel. 
						

							32
Email Notifications
The projector can send email notifications for a failed lamp/fan or over 
temperature condition. To configure click Email Notification in the top menu:
Projector Control
All projector operation and status can be accessed either by direct control from a 
browser or as part of an AMX or Crestron control system. 
Enable AMX device discovery in the Network Settings panel if the projector is 
co
ntr o

lled by an AMX control system. 
To control the projector in a browser click Projector Control in the top menu:
To configure the projector into a Crestron system, click Tools. 
						

							33
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•Projector must be off and the lens must be at room temperature.
• Av

oid using an excessive amount of cleaner, and don’t apply the cleaner 
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS: •Turn the projector off and unplug power cord before cleaning any part of 
the  pr

ojector.
• Do not touch or block the projector lens with any objects as this can 
damage the projector lens. Scratches, gouges and other lens damage are not 
covered by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing 
covers may expose you to dangerous voltage and other hazards. Refer all 
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the 
information that came with the lock for instructions on how to use it.
S-VIDEO
USB-B
USB-A
Security Lock 
						

							34
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the 
lamp has been in use.
• NOTE: Be sure to use the InFocus lamp module designed for this projector. You c

an order new lamps from www.infocus.com (in select areas), your 
retailer or your dealer. Only genuine InFocus lamps are tested for use in this 
projector. Use of non InFocus lamps may cause electrical shock and fire, and 
may void the projector warranty.  InFocus is not liable for the performance, 
safety or certification of any other lamps.
WARNINGS:
• The projector uses a high-pressure mercury glass lamp.  The lamp may fail  prematurel
 y, or it may rupture with a  popping sound if jolted, scratched, or 
handled while hot.  The risk of lamp failure or rupture also increases as the 
lamp age increases; please replace the lamp when you see the “Replace Lamp” 
message.
• To avoid burns, allow the projector to cool for at least 60 minutes before you  replac
e t

he lamp.
• Do not touch or block the projector lens with any objects as this can damage  the pr ojec

tor lens. Scratches, gouges and other lens damage are not covered 
by the product warranty. 
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can obscure  projec

tion sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event  that the lam

p ruptures, small glass fragments may be generated. The lamp 
module is designed to contain most of these fragments, but use caution when 
removing it. 
• Before replacing a ruptured lamp, clean the lamp compartment and dispose of  cleaning mat e

rials. Wash hands after lamp replacement. 
• When replacing the lamp while the projector is ceiling-mounted, wear  protec tiv

e eyewear to prevent eye injury.
Hg – Lamp contains mercury. Manage  in accordance with local disposal 
laws. See www.lamprecycle.org. 
						

							35
If your projector is BLACK, follow these instructions:
1
Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, located on top of the projector, by removing the screw 
on the side of the lamp door, sliding th e door right, and lifting the lamp door 
off.
4Loosen the captive screws that attach the lamp housing to the projector.   
NOTE: If the projector is installed on a ceiling mount, be careful not to drop 
the lam p

 module once the captive screws are loosened.
5Carefully lift the lamp straight up, off of the alignment pins; being careful not to 
pinch the lamp connector. Dispose of the lamp in an environmentally proper 
manner.
6Install the new lamp module, aligning the pins properly. Be careful not to pinch 
the lamp connector.
7Tighten the screws. (NOTE: If the pins have not been aligned properly, the 
screws will not tighten securely.)
8Replace the lamp door by (a) putting the lamp door down and (b) sliding it 
until it locks.
9Replace the lamp door screw and tighten securely.
10Plug in the power cord and press the Power button to turn the projector back 
on.
11To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service 
menu and select Reset Lamp Hours....
S-VIDEOUSB-B USB-Aturn off and unplug 
projector wait 60 minutes 
						

							36
If your projector is WHITE, follow these instructions:
1
Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, located on top of the projector, by removing the screw 
on the side of the lamp door, sliding th e door right, and lifting the lamp door 
off.
4Remove the screws that attach the light blocking plate and lamp housing to the 
projector. NOTE: If the projector is installed on a ceiling mount, be careful not 
to drop the lamp module once the captive screws are loosened.
5Remove the light blocking plate.
6Carefully lift the lamp straight up, off of the alignment pins; being careful not to 
pinch the lamp connector. Dispose of the lamp in an environmentally proper 
manner.
7Install the new lamp module, aligning the pins properly. Be careful not to pinch 
the lamp connector.
8Replace the light blocking plate.
9Tighten the screws. (NOTE: If the pins have not been aligned properly, the 
screws will not tighten securely.)
10Replace the lamp door by (a) putting the lamp door down and (b) sliding it 
until it locks.
11Replace the lamp door screw and tighten securely.
12Plug in the power cord and press the Power button to turn the projector back 
on.
13To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service 
menu and select Reset Lamp Hours....
S-VIDEOUSB-B USB-Aturn off and unplug 
projector wait 60 minutes
S-VIDEO
USB-B
USB-A
S-VIDEO
USB-BUSB-A
S-VIDEO
USB-BUSB-A
S-VIDEO
USB-BUSB-A 
						

							37
Numerics
3D Sync Invert 25
A
AC Power On 27
Aspect Ratio 24
Audio 10
Audio 1/Audio 2 7
Auto Image 24
Auto Off Time 27
Auto Source 27
AV Mute 26
B
Blank Key 26
Blank Screen 26
Brightness 24
C
Cable box 10
Ceiling Mount 24, 26
Closed Captions 26
Color Space 25
Computer 1 26
Computer 1/Computer 2 7
Computer 2 26
ConnectingVideo device 10
Connecting power 7
Contacting InFocus 18
Contrast 24 Customer service co
ntact information 18
D
Digital Zoom 26
E
Eco Blanking 27
Email Notifications 32
Ethernet connection 7
F
Factory Reset 28
Focus 9
Freeze Screen 26
G
Gamma 25
H
HDMI 26
HDMI connection 7, 10
HDTV 24
High Altitude Setting 27
Horizontal Position 25
Horz Shift 26
I
Instant Power On 27
Internal Speaker 26
K
Keypad 26
Keypad buttons 21
Keystone 24 
						

							38
L
Lamp Low Power 26
LightCast 5,19
LightCast Reader 10, 28
M
Magnify Level 26
Menu Transparency 26
menu usage 23
Mute 26
N
Network Configuration 31
O
Optional computer connections 7
Overscan 25, 26
P
Phase 25
PIN Protect 27
Power connector 7
Power cord 7
Power Saving Mode 27
Prevent PC Screen Saver 25
Programmed Dimming 26
ProjectorConnecting video devices 10
Keypad buttons 21
Menus 23
Positioning 6
Setting up 6 Troubleshooting problems 11
Projector Control 32
Projector Info 26, 27
R
Rear Project 26
Red/Green/Blue Gain 25
Red/Green/Blue Offset 25
remote control 19
Resetting the projector 28
S
Screen Aspect 10
Search Screen 27
Service 28
Sharpness 24
Show Messages 26
Source 26
Source Info 26, 27
S-video connection 10
Sync Threshold 25
T
Tint 25
Tracking 25
Troubleshooting 11
Troubleshooting the remote 19
TV tuner 10
U
USB 5
Using Network Features 31 
						

							39
V
Vert Shift 26
Vertical Position 25
VGA connection 7
Volume 24
Volume button 20
W
Warranty 18
Z
zoom 9