InFocus Projector IN2126HDx User Manual

							1
Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon 
97223-8368 USA
We declare under our sole responsibility that
 this projector conforms to the following 
directives and norms:
ErP Directive 2009/125/EC
EMC Directive 2014/30/EU
Low Voltage Directive 2006/95/EC
EMC: EN 55024, EN EN55032, EN 61000-3-2, EN 61000-3-3
Safety: IEC 60950-1:2005 (2nd Edition) + A1: 2009 and EN 60950-1:2006 + 
A11:2009 + A1:2010 + A12:2011 + AM 2:2013
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple 
Computer, Inc. IBM is a trademark or regist ered trademark of International Business 
Machines, Inc. Microsoft, PowerPoint, an d Windows are trademarks or registered 
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered 
trademarks of Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo are 
registered trademarks of Texas Instruments  and BrilliantColor™ is a trademark of Texas 
Instruments. InFocus, In Focus, and INFOCUS (s tylized) are either registered trademarks or 
trademarks of InFocus Corporation in  the United States and other countries.
NOTE: This product is covered electrical and electronic equipment under 
the European Unions Waste from El ectrical and Electronic Equipment 
(WEEE) Directive (2002/96/EC). The WEEE Directive requires that covered 
equipment be collected and managed separately from typical household waste 
in all EU member states. Please  follow the guidance of your local 
environmental authority or ask the shop where you purchased the product 
for collection or recycling options.
FCC Warning
This device complies with part 15 of the FCC  Rules. Operation is subject to the following 
two conditions: (1) This device may not cause ha rmful interference, and (2) this device must 
accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B 
digital device, pursuant to part 15 of the FC C Rules. These limits are designed to provide 
reasonable protection against harmful interfer ence in a residential installation. This 
equipment generates, uses and can radiate radi o frequency energy and, if not installed and 
used in accordance with the instructions , may cause harmful interference to radio 
communications. However, there is no guaran tee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circ uit different from that to which the receiver 
is connected.
--Consult the dealer or an experien ced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void authority 
to operate the equipment.
Canada
This Class B digital apparatus complies with Ca nadian ICES-003. Cet appareil numérique de la 
classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
cMETus
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory models: P105, P106
Input ratings: 100-240Vac, 4.0A, 50-60Hz
InFocus reserves the right to alter product offe rings and specifications at any time without 
notice. 
						

							2
Table of Contents
Introduction 4
Positioning the projector  6
Connecting a computer source  7
VGA connection  7
Ethernet connection  7
HDMI connection  7
Connecting power  7
Optional computer connections  7
Displaying an image  8
Adjusting the image  9
Connecting a video device  10 LightCast Reader 10
HDMI connection  10
Composite video connection  10
VGA connection  10
Component video connection  10
S-video connection  10
Audio 10
Shutting down the projector  11
Troubleshooting your setup  11
Using the remote control  19
Using the audio  20
Using the keypad buttons  21
Optimizing computer images  22
Presentation features  22
Optimizing video images  22
Customizing the projector  22
Using the menus
 23
Basic Menu  24
Advanced Menu  25
LightCast Reader   28
Using Network Features  31 Maintenance 33
Cleaning the lens  33
Using the security lock  33
Replacing the projection lamp  34 
						

							3
Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 15 degrees off 
axis.
•

Locate the projector at least 4 (1.2m) away from any heating or cooling vents.
• Do not block ventilation openings. Locate the projector in a well-ventilated  area witho

ut obstructions to intake or exhaust vents. Do not place the 
projector on a tablecloth or other soft covering that may block the vents.
• Do not place the projector in direct sunlight, humid, greasy or dusty places or  in places 
 where the projector may come into contact with smoke or steam.
• Do not touch or block the projector lens with any objects as this can damage  the projec
 tor lens. Scratches, gouges and other lens damage are not covered 
by the product warranty.
• Do not look directly into the lens while the projector is being used.
• Do not drop the projector.
• Do not spill liquid on the projector. Spilled liquid may damage the projector.
• Use the power cord provided. Connect the power cord to a receptacle with a  protectiv e

 safety (earth) ground terminal. A surge-protected power strip is 
recommended.
• Do not overload wall outlets.
• When disconnecting the power cord, hold the plug, not the cord.
• Wash hands after handling the cables supplied with this product.
• The projector remote control uses batteries. Make sure the batteries’ polarity  (+/-) is  aligned 

correctly. Dispose of used batteries in accordance with local 
disposal laws.
• Use an InFocus approved ceiling mount kit for proper fitting, ventilation and  installati
 on.  The warranty does not cover any damage caused by use of non-
approved ceiling mount kits or by installing in an improper location. 
• When the projector is ceiling mounted, wear protective eyewear to prevent  eye 
 injury before opening lamp door. • Refer all service to qualified service personnel. Servicing your own projector 
can be  dange

rous to you and will void the warranty.
• Only use replacement parts specified by InFocus.  Unauthorized substitutions  may r
 esult in fire, electrical shock, or injury, and may void the warranty
• Only genuine InFocus lamps are tested for use in this projector. Use of non  InFocus lam
 ps may cause electrical shock and fire, and may void the projector 
warranty. 
• Hg – Lamp contains mercury. Ma nage in accordance with local 
disposal laws. See www.lamprecycle.org.
• The projector uses a high-pressure mercury glass lamp.  The lamp may fail 
prematurely, or it may rupture with a popping sound if jolted, scratched, or 
handled while hot.  The risk of lamp fa ilure or rupture also increases as the 
lamp age increases; please replace the lamp when you see the “Replace Lamp” 
message.
• In the unlikely event of a lamp rupture, particles may exit through the  projec tor v

ents. Please keep people, food, and drinks at least 3’ (1m) away 
from all projector vents. For ceiling applications, keep people, food and drinks 
out of the keep out area under and around the projector, as indicated by the 
illustration.
Follow these instructions to help ensure image quality and lamp life over the life of 
the pr o
jec

tor. Failure to follow these instructions may affect the warranty. For 
complete details of the warranty, see the Warranty Booklet.
5 ’
/1.5m8 ’/2.4m
3’ / 1 m3’ / 1 m
3’ / 1 m
3’ / 1 m 
						

							4
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to 
maintain. It is a versatile projector that is flexible enough for business 
presentations and home video viewing too. The IN2124x/IN2124xw has native 
XGA 1024 x 768 resolution, the IN2126x/IN2126xw has native WXGA 1280 x 
800 resolution, and the IN2128HDx/IN2128HDxw has native 1080p 1920 x 1080 
resolution. They are compatible with a wide variety of computers and video 
devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our 
website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the included 
Quick Start Guide. Optional accessories can be found on our website at 
www.infocus.com/support or at your retailer or dealer.
Online registration
Register your projector on our website at www.infocus.com/register to activate 
your warranty and receive product updates, announcements, and registration 
incentives.
lens
remote control 
receiver (IR) focus 
keypad 
security bar
lamp cover
S-VIDEOUSB-BUSB-A
connector 
panel
power cord 
connector
focus  
						

							5
Connector panel
The projector provides both computer and video connection options.
• VGA computer (2)
• Composite video 
•HDMI
•S-video
• USB connector for firmware upgrades, mouse control and Screen Save mode.
• USB type A (2): for standard wireless mouse/keyboard, USB storage devices 
to be accessed b

y LightCast. 
• Ethernet connection for projector status and control.
• Monitor out, for VGA pass through to an external monitor.
• Audio inputs for video and computer.
• Audio output to external speakers.
• RS-232 serial control. Command control codes are on our support website at  www
.in

focus.com/support. 
S-VIDEO
USB-B USB-A
RS232
computer
composite video
audio in/out
security lock
S-video
monitor 
out
HDMIUSB-B
EthernetUSB-A 
						

							6
Positioning the projector
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The 
projector must be at least 39.4” (1.0m) from the projection screen.
• If you are installing the projector on the ceiling, we strongly recommend using  InFocus a

pproved ceiling mounts for proper  fitting, ventilation and installation. 
Refer to the installation guide that come s with the InFocus Ceiling Mount Kit (p/n 
PRJ-MNT-UNIV) for more information. The warranty does not cover any damage 
caused by use of non-approved ceiling mount kits or by installing in an improper 
location. To turn the image upside down, see “Ceiling mount” on  page 26. We 
recommend using an InFocus authorized ceiling mount.
• Position the projector the desired distance from the screen. The distance from the  lens of

 the projector to the screen and the video format determine the size of the 
projected image.
Minimum Distance to Screen OffsetOffset for 60in. Image
39.4/1.0m 15%+-5%9/22.9cm
60 inches 
high image
bottom of image 9 
inches above center 
of lens Projection angle
lens center
Table 1: IN2124x/IN2124xw(XGA) Screen size Throw Ratio = 1.9 to 2.09
Diagonal Screen Size 
(inches/m)  Size of the Projected Image 
Width
(inches/m) Distance to screen
Minimum distance
(inches/m)
Maximum distance
(inches/m)
40”/1.0m 32”/0.8m 61”/1.6m67”/1.7m
60”/1.5m 48”/1.2m 91”/2.3m100”/2.6m
80”/2.0m 64”/1.6m 122”/3.1m134”/3.4m
100”/2.5m 80”/2.0m 152”/3.9m167”/4.3m
150”/3.8m 120”/3.1m 228”/5.8m251”/6.4m
Table 2: IN2126x/IN2126xw (WXGA) Screen size 
Throw Ratio = 1.5 to 1.8
Diagonal Screen Size 
(inches/m)  Size of the Projected Image 
Width
(inches/m) Distance to screen
Minimum distance
(inches/m)
Maximum distance
(inches/m)
40”/1.0m 38”/1.0m 58”/1.5m69”/1.8m
60”/1.5m 58”/1.5m 87”/2.2m104”/2.6m
80”/2.0m 77”/2.0m 115”/2.9m138”/3.5m
100”/2.5m 96”/2.4m 144”/3.7m173”/4.4m
150”/3.8m 144”/3.7m 216”/5.5m260”/6.6m
Table 3: IN2128HDx/IN2128HDxw (1080p) Screen size 
Throw Ratio = 1.15 to 1.5
Diagonal Screen Size 
(inches/m) Size of the 
Proje
c
ted Image 
Width
(inches/m) Distance to screen
Minimum distance
(inches/m)
Maximum distance
(inches/m)
40”/1.0m 43”/1.1m49”/1.3m 64”/1.6m
60”/1.5m 64”/1.6m74”/1.9m 96”/2.4m
80”/2.0m 85”/2.2m98”/2.5m 128”/3.3m
100”/2.5m 107”/2.7m123”/3.1m 160”/4.1m
150”/3.8m 160”/4.1m184”/4.7m 240”/6.1m 
						

							7
Connecting a computer source
VGA connection
Connect one end of the provided computer cable to the Computer 1/Computer 2 
connector on the projector and the other to the VGA connector on your 
computer. If you are using a desktop computer, you will need to disconnect the 
monitor cable from the computer’s video port first.
Ethernet connection
Ethernet connection for projector status and control.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI 
provides an interface between sources, such as set-top boxes, DVD players, and 
receivers and your projector. Plug an HDMI cable into the video-out connector on 
the video device and into the HDMI connector on the projector.
Connecting power
Connect the black power cord to the Power connector on the rear of the 
projector and to your electrical outlet. If the Power Saving Mode feature is off, the 
Power LED on the Status Indicator Panel ( page 11) blinks green. If the Power 
Saving Mode feature is on, the Power LED is steady amber. By default, this feature 
is off. Yo u can change 

the setting, see page 27. NOTE: Always use the power cord 
that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not 
included) to your computer and to the Audio 1/Audio 2 connector on the 
projector. You may also need an adapter.
If you are using a desktop computer and wa nt to 
see th
 e image on your computer 
screen as well as on the projection screen, connect to the desktop’s computer 
cable to Computer 1 and the desktop’s monitor cable to the Monitor Out 
connector on the projector. 
S-VIDEOUSB-B USB-Aconnect VGA cable
LANS-VIDEOUSB-BUSB-Aconnect Ethernet cable
S-VIDEOUSB-BUSB-Aconnect HDMI
S-VIDEOUSB-BUSB-Aconnect power
S-VIDEOUSB-BUSB-Aconnect audio cable 
						

							8
Displaying an image
Press the Power button.
The Power LED blinks green, and the fans start to  
 run. When the lamp comes on, 
the start up screen displays and the Power LED turns solid green. It can take up to 
a minute for the image to achieve full brightness. Note: When the feature, AC 
Power On, is enabled, the projector automatically turns on when power is 
connected. This allows control of ceiling mounted projectors with a wall power 
switch.
No start up screen? Get help on  page 12.
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the Source 
but ton o n the

 projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a 
pr oje c

tor is connected. Usually a key combination like FN + F8 or CRT/LCD key 
turns the external display on and off. Locate a function key labeled CRT/LCD or a 
function key with a monitor symbol. Press FN and the labeled function key 
simultaneously. 
Refer to your laptops documentation for more information about your laptops 
ke y co

mbination.
No laptop image? Try pressing the Auto Image button on the remote. Get 
help o n

 page 12.
press Power button
turn on computer or 
video device
activate laptop’s external port
monitor key or 
LCD/CRT key
FN key 
						

							9
Adjusting the image
If necessary, adjust the height of the projector by rotating the elevator foot to 
extend the foot.
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust v
 ent at the front of the projector.
Position the projector the desired distance from the screen at a 90 degree angle to 
the scr e

en.
See  page  6 for a table listing screen sizes and distances.
Adjust the focus.
If the image is not square, first make sure that the projector is perpendicular to the 
scr
 een. If the image is larger or smaller on the top or bottom edge of the screen, 
press the top Keystone button   to reduce the upper part of the image, and press 
the bottom Keystone button   to reduce the lower part.
If the left or right side of the screen is larger or smaller the other, you can turn the 
pr oje
c

tor to the left or to the right a few degrees to square the image.
Adjust the Contrast or Brightness in the Basic Menu. See  page 24  for help with 
these menu adjustments.
adjust height
elevator 
foot
S-VIDEOUSB-BUSB-A
adjust distance
S-VIDEOUSB-B USB-A
adjust focus
S-VIDEOUSB-BUSB-A
adjust keystone
adjust Basic Menu