InFocus Projector In2114 User Manual

Regulatory models: V2000, M2100
IN2112, IN2114, IN2116
010-0735-00 

1
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, 
Oregon 97070 USA
We declare under our sole responsibility that this projector conforms to the 
following directives and norms:
EMC Directive 2004/108/EC
EuP Directive 2005/32/EC
EMC: EN 55022
 EN 55024
 EN 61000-3-2
 EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety:  IEC 60950-1:2005, MOD
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks 
of Apple Computer, Inc. IBM is a...

2
Table of Contents
Introduction 4
Positioning the projector  6
Ceiling Mount 7
Connecting power  8
Connecting a computer source  8
Optional computer connections 9
Displaying an image  10
Adjusting the image  11
Connecting a video device  12
Video device connections  12
Shutting down the projector  14
Troubleshooting your setup  14
Using the remote control  22
Using the audio  23
Using the keypad buttons  24
Optimizing computer images  24
Presentation features  24
Optimizing video images  25
Customizing...

3
Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 8 degrees off 
axis.
• Locate the projector at least 4 (1.2m) away from any heating or cooling 
vents.
• Do not block ventilation openings. Locate the projector in a well-
ventilated area without obstructions to intake or exhaust vents. Do not 
place the...

4
Introduction
Your new digital projector is simple to connect, easy to use, and 
straightforward to maintain. It is a versatile projector that is flexible enough 
for business presentations and home video viewing, too. The IN2112 has 
native SVGA 800 x 600 resolution, the IN2114 has native XGA 1024x768 
resolution, and the IN2116 has WXGA 1280x800 resolution. This guide 
applies to both products. They are compatible with a wide variety of 
computers and video devices.
Product specifications
To read the...

5
Connector panel
The projector provides both computer and video connection options, 
including:
•VGA computer (2)
•S-video
•Composite video
• Separate audio inputs for video and computer
The projector also provides the following connectors:
• Monitor out, to provide an image on your desktop computer as well as 
on the projection screen.
• Audio out, to provide sound for external speakers.
• 5 volt DC output
• RS-232 connector for serial control. Command control codes are 
available on our support...

6
Positioning the projector
To determine where to position the projector, consider the size and shape of 
your screen, the location of your power outlets, and the distance between the 
projector and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The 
projector must be at least 4.9’ (1.5m) from the projection screen.
• Position the projector within 10’ (3m) of your power source and within 
6’ (1.8m) of your video...

7
Ceiling Mount
If you wish to install the projector on the ceiling:
• We strongly recommend using InFocus approved ceiling mounts for 
proper fitting, ventilation and installation.  Refer to the installation 
guide that comes with the InFocus Ceiling Mount Kit (p/n SP-CEIL-
UNIV) for more information.  The warranty does not cover any dam
-
age caused by use of non-approved ceiling mount kits or by installing 
in an improper location.
• The ceiling must be strong enough to support the projector and the...

8
Connecting power
Connect the black power cord to the Power connector on the rear of the 
projector and to your electrical outlet. The Power light on the Status 
Indicator Panel (
page 14) turns amber.
NOTE: Always use the power cord that shipped with the projector.
Connecting a computer source
VGA connection
Connect one end of the provided computer cable to the VGA 1 or VGA 2 
connector on the projector and the other to the VGA connector on your 
computer. If you are using a desktop computer, you will...

9
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not 
included) to your computer and to the Audio 1 or Audio 2 connector on the 
projector. (Default settings are as follows: Audio 1 is used with VGA 1 and 
VGA 2; Audio 2 is used with S-video and composite.) You can also assign a 
your source to a different audio in connector, see 
page 23 and page 30. You 
may also need an adapter.
If you are using a desktop computer and want to see the image on...