InFocus Projector IN2100 User Manual

30
Audio Inputs: Assign an audio input to a specific video/computer source 
input. (Default settings are as follows: Audio 1 is used with VGA 1 and 
VGA 2; Audio 2 is used with S-video and composite.)
Press up or down to highlight the source you want to change, then press 
select or the left and right arrow keys to change that source’s audio input. 
Press menu when done changing audio inputs.
Auto Source: When this feature is On, the projector automatically finds the 
active source, checking the selected...

31
PIN Protect: The PIN (personal identification number) feature allows you to 
password protect your projector. Once you enable the PIN feature, you 
must enter the PIN before you can project an image. The default PIN on this 
projector is Menu-Up-Down-Select-Source. Use the navigation buttons on the 
remote or keypad to enter the correct 5-button press sequence. When all 5 
numbers are entered correctly, press the Select button on the remote or 
keypad to select OK. If the message “Wrong PIN” appears,...

32
Status and Service menu
Source Info: Displays current source settings (read-only).
Projector Info: Displays current projector settings (read-only).
Reset Lamp Hours: Resets the lamp hours used counter in the Projector Info 
menu to zero. Do this only after changing the lamp.
Factory Reset: Restores all settings to their default.
Service Code: Only used by authorized service personnel.
Help
Press Help (on the keypad or remote) at any time to get interactive help for 
solving common, picture, sound, and...

33
Using Network Functions (IN2114 & IN2116 only)
IMPORTANT: To enable network functions at all times (even when the pro-
jector is powered off), the Network item in the Always-On Functions sub-
menu in the Setup menu must be set to Yes (not No).
Projector network functions include:
• Configuring and controlling the projector via a web browser.
• Failure and warning alerts via email.
• Projector Management via SNMP.
• Controlling the projector via Scheduling.
NOTE: Projector web pages and emails sent by...

34
3Start a web browser on your computer.
4Enter the projectors IP address or host name (preceded by http://) into 
the web browsers address bar. Example: If the IP address is 
192.168.1.10, enter http://192.168.1.10 into the browsers address bar.
5The Log In to Projector Control page will be shown in the browser.
6Select Access type: Basic User or Administrator.
7Click Log In.
Navigating Projector Web Pages
The left side of every page shows a navigation bar. Click the links in the 
navigation bar to go...

35
Event Notifications Page (administrators only)
This page lets you configure the projector to automatically send email when 
specific events occur. 
E-Mail Settings tab: In the Account Used… section, enter the information 
needed for your projector to connect to an email sending (SMTP) server. 
Then in the Recipient E-Mail Addresses section, enter the email addresses of 
people who will receive emails, and for each address, select whether that 
address receives reminders and/or warnings and errors...

36
Custom: Click this link to show custom command entry options. With cus-
tom commands, you can perform additional commands not shown in the 
Available Commands list. The RS-232 command codes are available on our 
website at www.infocus.com/support. NOTE: Custom commands you enter 
here should be in write format (do not include ?), and should use < and > 
instead of ( and ). Example: to turn on the ceiling mount setting, use the 
custom command .
Security Settings Page (administrators only)
This page...

37
Using LitePort (IN2114 & IN2116 only)
LitePort displays a slide show of JPEG images stored on a USB flash drive 
connected to the projector. This feature eliminates the need for a computer 
source and can be integrated with common wall plates and conference room 
input/output panels.
Image File Types
LitePort displays image files in JPEG format only (file extensions .JPEG and 
.JPG). Other file types including PDF, BMP, TIFF, PNG, GIF, etc. are 
ignored.
Viewing a Slide Show
To view your pictures as a...

38
(For remaining items below, highlight the setting, then press Select one or 
more times to change the setting value.)
Auto Start: Select On to have the player start the slide show when the USB 
flash drive is first connected. Select Off to have the player display thumb
-
nails when the USB flash drive is first connected.
Show All Folders: Select On to have the slide show display all images in all 
folders. Select Off to have the slide show display images only from the cur
-
rent folder.
Fill Screen:...

39
Troubleshooting LitePort
• If images load slowly: Make sure you are using a newer USB 2.0- 
compatible (high speed) USB flash drive. Larger image file sizes may 
also slow down the player; to reduce file size, use an image editing pro
-
gram on your computer to resize images smaller; for the best balance 
between image quality and speed, resize images to be 1024 pixels wide.
• If no images are found, or some images are not shown, or you only see 
folder thumbnails but no images: Make sure that images...