InFocus Projector IN1501 User Manual

Regulatory models: P1501, P1503
IN1501, IN1503
009-1313-00 

1
Declaration of Conformity
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon 
97070-8238 USA
We declare under our sole responsibility that this projector conforms to the 
following directives and norms:
EuP Directive 2005/32/EC
EMC Directive 2004/108/EC
EMC: EN 55022
 EN 55024
 EN 61000-3-2
 EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 2005 (MOD)
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are...

2
Table of Contents
Introduction 3
Positioning the projector  5
Projector and device connector guide  6
Connecting a computer source  9
Required computer connections  
(DisplayLink or VGA)  9
Optional computer connections  9
Displaying an image  10
Adjusting the image  11
Connecting a video device  12
Video device connections  13
Composite video connection  13
HDMI 1.3 connection  13
VGA connection  13
Component video connection  13
Shutting down the projector  14
Troubleshooting your setup  14
Using the...

3 Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 15 degrees off 
axis.
• Locate the projector at least 4 (1.2m) away from any heating or cooling 
vents.
• Do not block ventilation openings. Locate the projector in a well-ventilated 
area without obstructions to intake or exhaust vents. Do not place the...

4
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward 
to maintain. It is a versatile projector that is flexible enough for business 
presentations and home video viewing too. The IN1501 has native XGA 1024x768 
resolution, and the IN1503 has WXGA 1280x800 resolution. This guide applies to 
all products. They are compatible with a wide variety of computers and video 
devices.
Product specifications
To read the latest specifications on your multimedia projector,...

5
Connector panel
The projector provides both computer and video connection options, including:
• VGA computer
•HDMI
• Composite video
• USB DisplayLink connector, for computer audio/video input. This USB 
connection also provides slide advance (and mouse control when used with 
an optional remote control only)
• LitePort, for connecting a USB flash drive containing images.
• Audio input for video and computer.
audio in
DisplayLink
security lock computer composite 
video
HDMILitePort (IN1503 only) 

6
Positioning the projector
To determine where to position the projector, consider the size and shape of your 
screen, the location of your power outlets, and the distance between the projector 
and the rest of your equipment. Here are some general guidelines:
• Position the projector on a flat surface at a right angle to the screen. The 
projector must be at least 4.9 feet (1.5m) from the projection screen.
• Position the projector within 10 feet (3m) of your power source and within 6 
feet (1.8m) of...

7
Connecting a computer source
DisplayLink
If you have a Windows or Macintosh computer, connect the USB cable between 
your computers USB port and the projectors DisplayLink connector*. Then to 
begin installation of the DisplayLink software:
Windows: Follow the instructions on the screen.
Macintosh: A folder will open containing a file named DisplayLink Installer.pkg. 
Open that file and follow the instructions on the screen. 
* For detailed DisplayLink instructions and troubleshooting, and to download...

8
Displaying an image
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp comes 
on, the start up screen displays and the Power button is steady green. It can take a 
minute for the image to achieve full brightness.
? No start up screen? Get help on page 13.
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the Source 
button on the projector’s keypad or remote.
If you are using a VGA cable to connect...

9
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot release 
button to extend the foot.
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the side of the projector.
Position the projector the desired distance from the screen at a 90 degree angle to 
the screen.
See page 6 for a table listing screen sizes and distances.
Adjust the zoom or focus.
If the image is not square,...