InFocus Projector IN124STx User Manual

30
Projector Control
All projector operation and status can be accessed either by direct control from a 
browser or as part of an AMX or Crestron control system. 
Enable AMX device discovery in the Network Settings panel if the projector is 
controlled by an AMX control system. 
To control the projector in a browser click Projector Control in the top menu:
To configure the projector into a Crestron system, click Tools. 

31
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•Projector must be off and the lens must be at room temperature.
•Avoid using an excessive amount of cleaner, and don’t apply the cleaner 
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
•Turn the projector off and unplug power cord before cleaning any part of 
the projector.
•Do...

32
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the 
lamp has been in use.
• NOTE: Be sure to use the InFocus lamp module designed for this projector. 
You can order new lamps from www.infocus.com (in select areas), your 
retailer or your dealer. Only genuine InFocus lamps are tested for use in this 
projector. Use of non InFocus lamps may cause electrical shock and fire, and 
may void the projector warranty.  InFocus is not liable for the...

33 If your projector is BLACK, follow these instructions:
1Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, located on top of the projector, by removing the screw 
on the side of the lamp door, sliding the door right, and lifting the lamp door 
off.
4Loosen the captive screws that attach the lamp housing to the projector.  
NOTE: If the projector is installed on a ceiling mount, be careful not to drop 
the lamp module...

34 If your projector is WHITE, follow these instructions:
1Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, located on top of the projector, by removing the screw 
on the side of the lamp door, sliding the door right, and lifting the lamp door 
off.
4Remove the screws that attach the light blocking plate and lamp housing to the 
projector. NOTE: If the projector is installed on a ceiling mount, be careful not 
to drop...

35
Numerics
3D Sync Invert 27
A
AC Power On 29
Aspect Ratio 26
Audio 1/Audio 2 8
Auto Image 26
Auto Off Time 30
Auto Source 29
AV Mute 28
B
Blank Key 28
Blank Screen 28
Brightness 26
C
Cable box 11
Ceiling Mount 26, 28
Closed Captions 28
Color Space 27
Computer 1 28
Computer 1/Computer 2 8
Computer 2 28
Connecting
Video device 11
Contacting InFocus 19
Contrast 26
Customer service contact information 19D
Digital Zoom 28
E
Eco Blanking 29
F
Factory Reset 30
Focus 10
Freeze Screen 28
G
Gamma 27
H
HDMI 28...

36
menu usage 25
Mute 28
O
Overscan 27, 28
P
Phase 27
PIN Protect 29
Power connector 8
Power cord 8
Power Saving Mode 29
Prevent PC Screen Saver 27
Programmed Dimming 29
Projector
Connecting video devices 11
Keypad buttons 22
Menus 25
Positioning 6
Setting up 6
Troubleshooting problems 12
Projector Info 28, 30
R
Rear Project 28
Red/Green/Blue Gain 27
Red/Green/Blue Offset 27
remote control 20
Resetting the projector 30
S
Screen Aspect 11Search Screen 29
Service 30
Sharpness 26
Show Messages 29
Source 28...