InFocus Projector IN124STa User Manual

30
Timer
Auto Off Time: automatically turns the projector off after no signals are detected for 
a preset number of minutes. If an active signal is received before the projector powers 
down, the image will be displayed.
High Altitude Setting
High Altitude: We recommend you turn on the High Altitude Mode when your envi-
ronment is between 5000 (1500m) and 10,000 (3000m) above sea level.
Network
Wired LAN
DHCP: Abbreviation for Dynamic Host Configuration Protocol. This 
protocol automatically assigns IP...

31
Controlling the projector through a LAN 
environment
The projector supports Crestron® software. With correct settings for the  
Network  menu, you can manage the projector from a computer using a web 
browser when
 the computer and the projector are properly connected to the 
same local area network.
Wired connection
Internet
IP Router
1Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the 
projector and the other end to the RJ45 port .
2Press Menu on the keypad or remote and then...

32
Wireless connection
To connect to the projector wirelessly, you need to plug an optional InFocus 
wireless dongle (p/n SP-WIFIUSB-2) 
to the USB Type A connector on the 
projector.
InFocus wireless dongle
(p/n SP-WIFIUSB-2)
How to setup AP mode:
1Make sure the projector is turned on.
2Select Type-A from source list.
3Go to  Settings  > WiFi , select  AP Mode  and set it to  ON. See page 47. AP 
mode is set to  ON by default. 
4Press  Menu on the keypad or remote and then go to  Advanced Menu > Setup...

33
Web controlling the projector
Once you have the correct IP address for the projector and the projector is on or 
in
 standby mode, you can use any computer that is on the same local area network 
to
 control the projector.
• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or 
higher.
• The screenshots in this manual are for reference only, and may differ 
depending on your browser.
1Enter the address of the projector in  the address bar of your browser and 
press  Enter....

34
About Crestron e-Control®
1The Crestron e-Control® page provides a variety of virtual keys to control the 
projector or adjust the projector’s image. 
i
i
You can press  
to reveal more 
buttons.
i. These buttons function the same as the OSD menus and remote control  functions. 
• Source List:  To switch the source, click on the desired source. 
• Menu:  Use to go back to the previous OSD menu, exit and save menu 
settings. 
• When you use the projector control panel or remote control to change the...

35
Please pay attention to the input length and character limitations (including 
character and punctuation restrictions) listed below:
Category ItemInput-LengthMaximum Number of 
Characters
Crestron Control
IP Address15
IP ID2
Port5
Projector
Projector Name10
Location9
Assigned To9
Network 
Configuration
DHCP (Enabled)(N/A)
IP Address15
Subnet Mask15
Default Gateway15
DNS Server15
User Password
Enabled(N/A)
New Password20
Confirm2
Admin Password
Enabled(N/A)
New Password20
Confirm20
/ > < $ % +    are...

36
Crestron RoomView
From the Crestron RoomView software in the 
Edit Room page, enter the IP 
Address (or hostname) as shown on th e projector’s on-screen display (OSD) 
menu, “05” for IPID, and “41794” for  the reserved Crestron control port.
For the Crestron RoomView user guide and information about RoomView settings 
and commands, go to: 
 
http://www.crestron.com/products/
roomview_connected_embedded_projectors_devices/resources.asp
Displaying images through EZ Display
Installation for Windows and...

iiiiv
v
i
ii
37
Using EZ Display
i.Split Screen : Display up to 2 computers or mobile devices in Split Screen 
using the L and R buttons.
ii. Mirror/Extended Display : To duplicate your computer display onto the pro-
jector, click Mirror. To extend your desktop display onto the projector, click 
Extension .
iii.Video/Graphic Display : To display the best image quality, but with a slightly 
slower transmission speed, click  Video. To display images faster, but with 
slightly less quality, click  Graphic....

38
3Select WLAN  from source list. AP Info page displays.
AP InfoAP             IN124a-380343
IP              192.168.111.1
PSK PassCode
3522
4Establish WiFi connection with your source device first, and launch EZ Display/
EZ Remote app on your mobile device.
iOS screen
Android screen
EZ Remote
Launch EZ Remote. You will see the connected device shown on the device list. 
Click it to enable Remote control.
iOS screen
Android screen
*Skin button is reserved for future feature.
EZ Display
Launch EZ...

39
EZ Display: Streaming Doc
To stream your documents, transfer th
e documents you want from the computer 
to your mobile device and disconnect your mobile device. Documents will be 
organized by their format type.
Select a file to display it wirelessly. Click the Sketch icon to begin drawing and 
annotating your file. Click Save when you are done editing.
iOS screen
Android screen
EZ Display: Pix Viewer
To display your photos, select  Photo Gallery and select your photo. You can also 
draw on it with...