InFocus Projector IN118HDxc User Manual

							30
TimerAuto Off Time : aut
 omatically turns the projector off after no signals are 
detected for a preset number of minutes. If an active signal is received before 
the projector powers down, the image will be displayed.
High Altitude Setting High Altitude : W
 e recommend you turn on the High Altitude Mode when 
your environment is between 5000' ( 1500m) and 10,000' (3000m) above sea 
level.
Status/Service:
Source Info : a read-only display of current source settings.
Projector Info : a read-only 
 display of current projector settings and lamp 
hours.
Reset Lamp Hours... : resets 
 the lamp hours used counter in the Projector Info 
menu to zero. Do this only after changing the lamp.
Factory Reset...: 
 restores all settings to their default.
Service Code... : only used by authorized service 
 personnel. 
						

							31
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Projector must be off and the le ns
  must be at room temperature.
• Avoid using an excessive amount of  cleaner, and don’t apply the cleaner 
directly to the lens. Abrasive cleane rs, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS: • Turn the projector off and unplug power cord before cleaning any part of the pro
 jector.
• Do not touch or block the projector lens  with any objects as this can damage 
the projector lens. Scratches, gouges a nd other lens damage are not covered 
by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this pr oduct yourself as opening and removing 
covers may expose you to dangerous vol tage and other hazards. Refer all 
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the 
information that came with the lock  for instructions on how to use it.
Security Lock 
						

							32
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the 
lamp has been in use.
• NOTE: Be su
 re to use the InFocus lamp module designed for this projector. 
You can order new lamps from  www.infocus.com (in select areas), your 
retailer or your dealer.  Only genuine InFocus lamps are tested for use in this 
projector.  Use of non InFocus lamps may cause electrical shock and fire, and 
may void the projector warranty.  InFocu s is not liable for the performance, 
safety or certificati on of any other lamps.
WARNINGS :
• The projector uses a high-pressure me r
 cury glass lamp.  The lamp may fail 
prematurely, or it may rupture with  a popping sound if jolted, scratched, or 
handled while hot.  The risk of lamp fa ilure or rupture also increases as the 
lamp age increases; please replace the lamp when you see the “Replace Lamp” 
message.
• To avoid burns, allow the projector to  cool 
 for at least 60 minutes before you 
replace the lamp.
• Do not touch or block the projector lens  with any objects 
 as this can damage 
the projector lens. Scratches, gouges a nd other lens damage are not covered by 
the product warranty. 
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass 
 may shatter and cause injury.
• Do not touch the glass surface of the  lamp module. 
 Fingerprints can obscure 
projection sharpness and may ca use the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event  that 
 the lamp ruptures, small glass fra gments may be generated. The lamp 
module is designed to contain most of  these fragments, but use caution when 
removing it. 
• Before replacing a ruptured lamp, clea n 
 the lamp compartment and dispose of 
cleaning materials. Wash hands  after lamp replacement. 
• When replacing the lamp while the  projector is 
 ceiling-mounted, wear 
protective eyewear to prevent eye injury.
Hg – Lamp contains  mercury. Manage in accordance with local disposal 
laws. See  www.lamprecycle.org . 
						

							33
1
Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly. 
3Remove the lamp door, loca
ted on top of the projector, by removing the screw 
on the side of the lamp door, sliding the door right, and lifting the lamp door off.
4Loosen the captive screws that attach  the lamp housing to the projector.  
NOTE: I
f the projector is installed on a  ceiling mount, be careful not to drop the 
lamp module once the captive screws are loosened.
5Carefully lift the lamp straight up, off of  the alignment pins; being careful not to 
pinch the lamp connector. Dispose of th e lamp in an environmentally proper 
manner.
6Install the new lamp module, aligning the  pins properly. Be careful not to pinch 
the lamp connector.
7Tighten the screws. ( NOTE: If the pins have not been aligned properly, the 
screws will not tighten securely.)
8Replace the lamp door by (a) putting the la mp door down and (b) sliding it until 
it locks.
9Replace the lamp door screw and tighten securely.
10Plug in the power cord and press the  Power button to turn the projector back on.
11To reset the lamp hour ti mer, navigate to the Advanced Menu > Status/Service 
menu and select  Reset Lamp Hours... .
turn off and unplug 
projector wait 60 minutes
loosen screws 
						

							34
Numerics
3D Sync Invert 27
A
AC Power On 29
Aspect Ratio 26
Audio 1/Audio 2 8
Auto Image 26
Auto Off Time 30
Auto Source 29
AV Mute 28
B
Blank Key 28
Blank Screen 28
Brightness 26
C
Cable box 11
Ceiling Mount 26, 28
Closed Captions 28
Color Space 27
Computer 1 28
Computer 1/Computer 2 8
Computer 2 28
ConnectingVideo device 11
Contacting InFocus 19
Contrast 26
Customer service contact information 19 D
Digital Zoom 28
E
Eco Blanking 29
F
Factory Reset 30
Focus 10
Freeze Screen 28
G
Gamma 27
H
HDMI 28
HDTV 26
High Altitude Setting 30
Horizontal Position 27
Horz Shift 28
I
Instant Power On 29
Internal Speaker 28
K
Keypad 28
Keypad buttons 22
Keystone 26
L
Lamp Low Power 29
M
Magnify Level 28
Menu Transparency 29 
						

							35
menu usage 25
Mute 28
O
Overscan 27, 28
P
Phase 27
PIN Protect 29
Power connector 8
Power cord 8
Power Saving Mode 29
Prevent PC Screen Saver 27
Programmed Dimming 29
ProjectorConnecting video devices 11
Keypad buttons 22
Menus 25
Positioning 6
Setting up 6
Troubleshooting problems 12
Projector Info 28, 30
R
Rear Project 28
Red/Green/Blue Gain 27
Red/Green/Blue Offset 27
remote control 20
Resetting the projector 30
S
Screen Aspect 11 Search Screen 29
Service 30
Sharpness 26
Show Messages 29
Source 28
Source Info 28, 30
Sync Threshold 27
T
Tint 27
Tracking 27
Troubleshooting 12
TV tuner 11
U
USB 5
V
Vert Shift 28
Vertical Position 27
Volume 26
Volume button 21
W
Warranty 19
Z
zoom 10