InFocus Projector IN114STa User Manual

20
Using the remote control
The remote uses two (2) AAA batteries (not provided). They are easily installed 
by removing the cover from the remote’s back, aligning the + and - ends of the 
batteries, sliding them into place, and then replacing the cover.
Caution: 
• When replacing the remote batteries, be aware that using batteries other 
than
  AAA batteries may risk severe damage to the remote. When disposing 
of the batteries, be sure to do so in an enviromentally proper manner.
• If the remote...

21
Using the audio
Using the projector’s speakers
Connect the audio source to the Audio 1/Audio 2 connectors to hear audio 
through the projector speakers.  
Amplified speakers may also be connected to the projector using the Audio Out 
co
 nnector.
To adjust the volume, press the  Vo
 lume buttons on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
• Make sure the audio cable is connected to the  Audio 1/
 Audio 2 connector on 
the projector, and that the other end...

22
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of 
their functions:
Power–turns t
 he projector on and off (page  9).
Right arrow  - Whe
 n the menu is displayed, the right arrow button navigates 
through the menu.
Up arrow/Keystone  - Whe
 n the menu is displayed, the up arrow button navigates 
through the menu. When the menu is not displayed, this button adjusts the 
squareness of the image ( page 10).
Down arrow/Keystone  
 - When the menu...

23
Optimizing computer images
After the projector is running and the image is on the screen, you can optimize the 
image using the onscreen menus. For general information on using the menus, see 
page 25.
• Select default image settings using a preset appropriate to your environment.
• Adjust the Keystone, Contrast, or Brightness ( page 26).
• Change the Aspect Ratio. Choose the option that best fits your input source  (page  26).
• Adjust the Color Temperature ( page 27).
• Adjust the Phase, Tracking,...

24
Optimizing video images
After your video device is connected properly and the image is on the screen, you 
can optimize the image using the onscreen menus. For general information on 
using the menus, see page 25.
• Adjust the Keystone, Contrast, Brightness, Color, or Tint ( page 26 ).
• Change the Aspect Ratio. Choose the option that best fits your input source  (page  26).
• Select a Sharpness setting ( page 26).
• Adjust the Color Temperature. Select a listed warmth value ( page 27).
• Turn on...

25
Using the menus
1To open the menus, press the Menu button on the keypad or remote. (The 
menus automatically close after 60 seconds if no buttons are pressed.) Use the 
arrow buttons to move up and down to review the menu options.
2To enter a submenu, highlight the desi red submenu and press > on the keypad 
or Select on remote.
3To adjust a menu setting, highlight the desired menu option and press < or > 
to scroll through the available adjustments. 
4Press the  Menu button to exit the menu system....

26
Basic Menu
To adjust the following settings, highlight the setting, use the right and left arrows 
to adjust the values.
Aspect Ratio: Aspe
 ct ratio is the ratio of the image width to image height. TV 
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the 
unmodified inp
 ut with no resizing by the  projector. Select 16:9 to watch enhanced 
widescreen DVDs.
Auto Image : 
 resets the projector to the source.
Brightness :...

27
Advanced Menu
Image: 
3D Control:3D: allow
s you to enjoy 3D (stereoscopic) content. Your projector supports 
Auto, Top-Bottom, Frame Sequential, Frame Packing, Side-by-Side for con -
trolling LCD shutter glasses. In addition to the projector, you will need a pair 
o
 f 3D shutter glasses, 3D content, and 3D compatible source (and emitter).  
Ensure the glasses you choose are cons istent with the synchronization mode 
you will be using.
3D Sync Invert:  If the
  image appears to flutter,  look odd or...

28
Setup:
Audio Setup...
Internal Speaker : 
 turns the internal speaker on or off.
Computer 1: 
 selects the audio input for Computer 1 signal.
Computer 2: 
 selects the audio input for Computer 2 signal.
Video :
 selects the audio input for video source.
HDMI : select the
  audio input for HDMI signal.
Closed Captioning... Closed Captions
: controls closed captioning. If the source is NTSC and 
contains captions on the selected channel, then the projector will display 
caption text overlaid on the...

29
Lamp...Programmed Dimming : When enabled, Program
 med Dimming enhances con-
trast ratios in dark scenes and disables Lamp Low Power. Programmed Dim -
ming will impact lamp life and system noise performance. Programmed 
Dim
 ming works in conjunction with the lamp. If Lamp Low Power is enabled, 
Programmed Dimming is unavailable.
Lamp Low Power :
  toggles between on and off. Turn it on to lower the light 
output of the lamp. This also lowers the fan speed, making the projector qui -
eter.
OSD...