InFocus Projector IN1100 User Manual

							30
Advanced > Status/Service menu
Factory Reset: restores all settings to their default.
Projector Info: a read-only display  of
  current projector settings.
Reset Lamp Hours : resets the lamp h
 ours used counter in the Projector Info menu 
to zero. Do this only after changing the lamp.
Source Info : a read-only 
 display of current source settings.
Service Code : only used by 
 authorized service personnel.
Advanced > Status/Service menu 
						

							31
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of  cleaner,
  and don’t apply the cleaner 
directly to the lens. Abrasive cleane rs, solvents or other harsh chemicals 
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the 
information that came with the lock for instructions on how to use it.
USBcomputer inHDMIvideo 1video 2audio outaudio in
security 
lock 
						

							32
Replacing the projection lamp
The lamp hours used timer in the Projector Info menu counts the number of hours 
the lamp has been in use. Twenty hours before the lamp life expires, the message 
“Change lamp” appears on the screen at startup.
• NOTE:  Y

ou can order new lamps from  www.infocus.com (in select areas), 
your retailer or your  dealer. Only genuine InFocus  lamps are tested for use in 
this projector. InFocus is not liable for the performance, safety or certification 
of any other lamps. The use of other la mps violates the projector warranty and 
voids all certif ication marks on this projector.
WARNINGS :
• To avoid burns, allow the projector to  cool 
f
 or at least 60 minutes before you 
replace the lamp.
• Only genuine InFocus lamps are tested w ith 
thi
 s projector. Use of other lamps 
may cause electrical  shock and fire.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass  may shatter and 
 cause injury.
• Do not touch the glass lamp screen . Fingerpri
 nts can obscure projection 
sharpness.
• Be extremely careful when removing the lamp housing. In the unlikely event  that th
 e lamp ruptures, small glass fra gments may be generated. The lamp 
module is designed to contain most of  these fragments, but use caution when 
removing it. Before replac ing a ruptured lamp, clean the lamp compartment 
and dispose of cleaning  materials. Wash hands after lamp replacement.
Hg – Lamp contains mercury. Manage in  a
cco
 rdance with local disposal laws. 
See  www.lamprecycle.org .
Lamp hours
USBcomputer inHDMIvideo 1video 2audio outaudio inturn off and unplug 
projector
wait 60 minutes 
						

							33
1
Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly.
3Turn the projector upside down on a soft 
cloth so that the lamp door is facing 
you.
4Loosen the two captive screws on th e lamp door and lift the door off.
5Loosen the two captive screws that attach the lamp housing to the projector.
6Carefully remove the lamp housing. Dispos e of the lamp in an environmentally 
proper manner.
7Install the new lamp housing and tighten the screws.
8Replace the lamp door.
9Plug in the power cord and press the Power button to turn the projector back on.
10To reset the lamp hour ti mer, navigate to the Advanced > Status/Service  menu 
and select  Reset Lamp Hours . See page 30  for details.
USBcomputer inHDMIvideo 1video 2audio outaudio in
loosen screw
loosen screw 
						

							34
INDEX
Numerics
3D Control
3D 25
3D Sy

nc Invert 25
A
Advanced > Image > 3D Control Menu 25
B
Basic menu 24
Aspect Ratio 24
Auto Image 24
Brightness 24
Con

trast 24
Keystone 24
Preset 24
Sharpness 24
Volume 24
C
cleaning the lens 31
Color 25 Blue Gain 

25
Color 25
Color Space 25
Color Temp 25
Gamma 25
Green Gain 25
Red Gain 25
Tint 25
White Peaking 25
Computer In connector 6
connector panel 4 Audio in 4
Audio out 4
Composite video 4
HDMI 4 MINI USB Type B connector 4
S-video 4
VESA computer 4
contacting InFocus 17
Custom key 21
customer service c ontact information 17
customizing the projector 22
D
DVDs 24
F
Factory Reset 30
focus 8
H
HDTV 24
I
image optimizatio
 n 21
size 5
K
keypad buttons 20
Auto Image 
 20
Keystone 20
Menu 20
Power 20
Presets 20
Select 20
Source 20
Up/Down/Left/Right arrows 20
keystone, adjusting 8
L
lamp hours, resetting 33
laptop
  video port activation 7
LEDs 10
M
maintaining the projector 31
menu usage 
 23 
						

							35
O
optimizing images 21
optimizing video 
22
Overscan 25, 26, 27, 28, 29
P
PC 25 F
 orce Wide 25
PC Screen Saver 25
Phase 25
Tracking 25
positioning the projector 5
Power connector 6
power cord 6
presentation features 21
projection distance 5
projector connector panel 4
customization 22
image size 5
keypad buttons 20
maintenance 31
menus 23
offset 5
positioning 5
registering 3
reset 30
safety considerations 2
security lock 31
setting up 5
shutting down 10
Status Indicator Panel 10
troubleshooting problems 10
R
registering your projector 3
remote control 18
Auto Image 18 Blank 18
Custom 18
Mute 18
Pre

sets 18
Resize 18
Source 18
Volume 18
resetting the projector 30
S
security lock 31
Se
 rvice 30
Service Code 30
Settings menu 26
sharpness 24
shutting down the projector 10
Status Indicator Panel 10
S-video connector 9
T
troubleshooting 10
U
USB 6
V
Video 25 Over
 scan 25
video devices, connecting 9
video optimizing 22
Video Standard 26
Volume button 19
W
warranty 17
Z
zoom 8