InFocus Projector In104 User Manual

Operation 31
Adjusting Color
Highlight Color in the PICTURE menu and adjust the values by pressing  / on 
the projector or remote control.
Lower setting produces less saturated colors. If the setting is too high, colors on the 
image will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight Tint in the PICTURE menu and adjust the values by pressing  / on 
the projector or remote control.
The higher the value, the more reddish the picture becomes. The lower the value, 
the more...

Operation 32
3D Color Management
In most installation situations, color management will not be necessary, such as in 
classroom, meeting room, or lounge room situations where lights remain on, or 
where building external windows allow daylight into the room. 
Only in permanent installations with controlled lighting levels such as boardrooms, 
lecture theaters, or home theaters, should color management be considered. 3D 
Color Management provides fine color control adjustment to allow for more 
accurate...

Operation 33
Saturation is the amount of that color in a video picture. Lower settings produce less 
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation 
is too high, that color will be overpowering and unrealistic.
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you 
achieve better time management when giving presentations. Follow these steps to 
utilize this function:
1. Go to the SYSTEM SETUP:...

Operation 34
To cancel the timer, perform the following steps.
1. Enter the SYSTEM SETUP: Basic > Presentation Timer menu and highlight 
Off. Press MODE/ENTER. A confirmation message displays.
2. Highlight Ye s and press MODE/ENTER to confirm. You will see the message 
“Timer is Off” displaying on the screen. 
Hiding the image
In order to draw the audiences full attention to 
the presenter, you can use BLANK on the 
projector or remote control to hide the screen 
image. Press any key on the projector or...

Operation 35
Freezing the image
Press   on the remote control to freeze the 
image. The word FREEZE will display in the 
upper left corner of the screen. To release the 
function, press any key on the projector or 
remote control.
Even if an image is frozen on the screen, the 
pictures are running on the video or other device. 
If the connected devices have active audio 
output, you will still hear the audio even though the image is frozen on screen.
Operating in a high altitude environment
We recommend...

Operation 36
Adjusting the sound level
To adjust the sound level:
1. Repeat steps 1-2 above.
1. Press  to highlight Volume and press  /  to select a desired sound level.
Personalizing the projector menu display
The On-Screen Display (OSD) menus can be set according to your preferences. 
The following settings do not affect the projection settings, operation, or 
performance. 
Menu display time in the SYSTEM SETUP: Advanced > Menu Settings 
menu sets the length of time the OSD will remain active after...

Operation 37
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal 
type selected.
The menu items are available when the projector detects at least one valid signal. If 
there is no equipment connected to the projector or no signal detected, limited 
menu items are accessible.
Main menu Sub-menu Options
1. 
DISPLAY
Wall ColorOff/Light Yellow/Pink/Light 
Green/Blue/Blackboard
Aspect Ratio Auto/Real/4:3/16:9
Keystone
Position
Phase
H. Size
Digital Zoom...

Operation 38
4. 
SYSTEM 
SETUP: 
Basic
Language
Projector PositionFront Table/Rear Table/Rear 
Ceiling/Front Ceiling
Auto Power OffDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Blank TimerDisable/5 min/10 min/15 min/20 
min/25 min/30 min
Panel Key Lock On/Off
Timer ControllerDisable/30 min/1 hr/2 hr/3 hr/4 
hr/8 hr/12 hr
Splash ScreenBlack/Blue/InFocus
5. 
SYSTEM 
SETUP: 
Advanced
Quick Cooling On/Off
High Altitude Mode On/Off
Audio SettingsMute On/Off
Volume
Menu SettingsMenu display 
time5 sec/10...

Operation 39
Description of each menu
FUNCTIONDESCRIPTION
Wall ColorCorrects the projected picture’s color when the projection 
surface is not white. See Using Wall Color on page 30 for 
details.
Aspect RatioThere are four options to set the images aspect ratio 
depending on your input signal source. See Selecting the 
aspect ratio on page 27 for details.
KeystoneCorrects any keystoning of the image. See Correcting 
keystone on page 26 for details.
Position
Displays the position adjustment page. To move...

Operation 40
FUNCTIONDESCRIPTION
Preset ModePre-defined picture modes are provided so you can optimize 
your projector image set-up to suit your program type. See 
Selecting a picture mode on page 29 for details.
BrightnessAdjusts the brightness of the image. See Adjusting Brightness 
on page 30 for details.
ContrastAdjusts the degree of difference between dark and light in the 
image. See Adjusting Contrast on page 30 for details.
ColorAdjusts the color saturation level -- the amount of each color in 
a...